FORTIN 91311 GMC Canyon 2020 Standard Key Remote Starters and Alarm Systems Installation Guide
- June 13, 2024
- FORTIN
Table of Contents
THAR-GM7 THARNESS INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION
91311 GMC Canyon 2020 Standard Key Remote Starters and Alarm Systems
Vehicle functions supported in this diagram (functional if equipped)
| BYPASS FIRMWARE VERSION| To add the firmware version and the options, use
the
FLASH LINK UPDATER or FLASH LINK MOBILE tool,
sold separately.
---|---|---
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:| A11| | Hood trigger
(Output Status).
---|---|---|---
| Program bypass option:| UNIT OPTION| DESCRIPTION
---|---|---|---
C1| OEM Remote status (Lock/Unlock) monitoring
| Program bypass option
(If equiped with OEM alarm):| D2| Unlock before / Lock after (Disarm OEM
alarm)
---|---|---|---
ATTENTION!| | E5| | By default DEACTIVATED
---|---|---|---|---
| MANUFACTURED MODULES
BETWEEN: 04/2018 TO04/2019
| Program remote
starter option for R.S. OEM
REMOTE STAND ALONE:| FUNCTION| MODE| DESCRIPTION
---|---|---|---|---
38| 2| Enable: Press 3x Lock to remote start with the OEM remote.
The vehicles Flip-key remote will not be functional during remote start.
Parts required (Not included)
1X 180 Ohm resistor (Manual transmission)
1X 1Amp. diode (Manual transmission)
MANDATORY INSTALL
*HOOD PIN HOOD STATUS: THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED
IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO
OFF. SECURITY STICKER
Notice: the installation of safety elements are mandatory. The hood pin and
the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION
CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
DESCRIPTION
AUTOMATIC TRANSMISSION WIRING CONNECTION
MANUAL TRANSMISSION WIRING CONNECTION
DCRYPTOR PROGRAMMING PROCEDURE
Parts required (not included)
FLASH LINK UPDATER,
FLASH LINK MANAGER
SOFTWARE | PROGRAMME
Microsoft Windows Computer with Internet connection
OR
OU
FLASH LINK MOBILE
FLASH LINK MOBILE APP
Smartphone Android or iOS with Internet connection (Internet provider charges
may apply) BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE. Press and
hold the programming button:
Connect the 4-PIN Data-link harness (Black connector).
The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes. Release
the programming button when the LED is YELLOW.
If the LED is not solid YELLOW disconnect the 4 Pin connector (Data-Link) and
go back to step 1. Insert the required remaining connectors. Press and release
the programming button five times (5x).
The YELLOW LED will alternate between 5x flashes and a pause. Wait until the
YELLOW LED turns ON. Turn the Ignition to the ON/RUN position.
The RED LED will turns ON.
The YELLOW LED turns OFF.
If the LED is not solid RED disconnect the 4 Pin connector (Data-Link) and go
back to step 1. Turn the Ignition to the OFF position. Remove the key from the
ignition barrel.
CONTINUED NEXT PAGE Wait 5 seconds. If the LEDs do not react as shown,
the 6-Pin disconnect connector (Main-Harness) and go back to step 1. WITHOUT
ON-STAR®
Press and release the programming button once (1x). Turn the key to the OFF
position.
the BLUE LED flash slowly.
REMOTE STARTER FUNCTIONALITY
MANUAL TRANSMISSION: READY MODE TAKE OVER AUTOMATIQUE TRANSMISSION
REMOTE STARTER PROGRAMMING PROCEDURE
REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE
STARTER PROGRAMMING. Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a
regular basis. We recommend that you update this module to the latest fi rmware
and download the latest installation guide(s) prior to the installation of
this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever. It is the sole
responsibility of the installer to check and verify any circuit before
connecting to it. Only a computer safe logic probe or digital multimeter
should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or
responsibility whatsoever pertaining to the accuracy or currency of the
information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualifi ed technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest version.
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE
Copyright © 2006-2018, FORTIN AUTO RADIO INC
ALL RIGHTS RESERVED PATENT PENDING
This guide may change without notice. See
www.fortin.ca for latest version.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>