LeoVince 14387E LV One EVO Slip On Exhaust Instruction Manual

: June 13, 2024
: LeoVince

Table of Contents

14387E LV One EVO Slip On Exhaust
LIST OF COMPONENTS
FITTING INSTRUCTION
INSTALLATION:
MAINTENANCE:
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TECHNICAL INFORMATION
ART. 14387E – 14387EB – 14388E SLIP-ON \
HONDA NC 750 X
(fits with original panniers) (also fits 35kW versions)
(Fits with original center stand)
TYPE: RH09; 1/1; 1CV/1; 2/1; 2CV/1

14387E LV One EVO Slip On Exhaust

ART. 14387E – 14387EB – 14388E
Given name
Surname
Address
Vehicle registration plate
Tel.
Date and seller’s stamp

LIST OF COMPONENTS

| STAINLESS S.| BLACK| CARBON FIBER
---|---|---|---
1 – Muffler| cod. 308402481| cod. 3014346485| cod. 308403481
2 – Link pipe| cod. 3014387201| cod. 3014387201| cod. 3014387201
3 – Clamp| cod. 303984502| cod. 303984502| cod. 303984502
4 – Fitting kit| cod. 3014387601| cod. 3014387601| cod. 3014387601
PESO – WEIGHT – POIDS – GEWICHT (Kg)

ORIGINALE – STOCK – ORIGINE – ORIGINAL 3,36 (Kg)
| Stainless steel| S.s black| Carbon
Leo Vince| 2,63| 2,63| 2,23

LeoVince 14387E LV One EVO Slip On Exhaust - Figure 2

ART. 14387E
HONDA NC 750 X (Also fits 35kW version)
(Fits with original panniers) (Fits with original centre stand)
SLIP-ON – LV ONE EVO – STAINLESS STEEL – APPROVED

LeoVince 14387E LV One EVO Slip On Exhaust - Figure 5

ART. 14387E – SPARE PARTS
HONDA NC 750 X (Also fits 35kW version)
(Fits with original panniers) (Fits with original centre stand)
A FITTING KIT cod.3014387601R LeoVince 14387E LV One EVO Slip On Exhaust -
Figure 6

ART. 14387EB
HONDA NC 750 X (Also fits 35kW version)
(Fits with original panniers) (Fits with original centre stand)
SLIP-ON – LV ONE EVO – STAINLESS STEEL BLACK – APPROVED LeoVince 14387E LV
One EVO Slip On Exhaust - Figure 7

ART. 14387EB – SPARE PARTS
HONDA NC 750 X (Also fits 35kW version)
(Fits with original panniers) (Fits with original centre stand)
A FITTING KIT cod.3014387601R LeoVince 14387E LV One EVO Slip On Exhaust -
Figure 3

ART. 14388E
HONDA NC 750 X (Also fits 35kW version)
(Fits with original panniers) (Fits with original centre stand)
SLIP-ON – LV ONE EVO – CARBON – APPROVED LeoVince 14387E LV One EVO Slip On
Exhaust - Figure 4

ART. 14388E – SPARE PARTS
HONDA NC 750 X (Also fits 35kW version)
(Fits with original panniers) (Fits with original centre stand)
A FITTING KIT cod.3014387601R

FITTING INSTRUCTION

LIST OF SUPPLIED PARTS:
Refer to the list of components and the product drawing included in this booklet.
WARNING:
before carrying out any work on the exhaust, check that its surface has cooled so that it will not damage components, which are not heat-resistant (such as fairing, hoses, rubber sleeves, etc.), or the operator.

INSTALLATION:

Remove the OE silencer.
Check that the mating surfaces are in good clean condition, slide the link pipe on to the original header, taking care not to damage the graphite bushing (if supplied) which should replace the OE bushing. Partially tighten the securing strap to allow a degree of further adjustment.
Slide the Leovince silencer onto the link pipe, check the alignment of the mounting eyes for the springs and the alignment of the exhaust outlet to the rear of the silencer, and then link the parts together with the springs provided
Fit the clamp to the silencer. Mount spacers, washers and brackets (if any) as shown on the drawing and then secure by tightening nuts and bolts. (Photo 1)
Tighten the various clamps which join the Leovince link pipe to the OE exhaust headers.
Start the engine, wait a few minutes until it reaches operating temperature, and check that there are no gas leaks.

IMPORTANT:
During the first km of running, the exhaust system needs breaking-in; therefore, slight gas leakage might occur. After approximately 100 Km, check all the fasteners.
ADJUSTEMENT:
This silencer has been developed by Leovince on an electronic dynamometer using a vehicle in perfect condition, and in standard trim

MAINTENANCE:

From time to time, check all the brackets and fasteners, which could be affected by use (sound-deadening material, seals and other rubber parts) and replace them periodically.
The silencer may be cleaned using gasoline, diesel oil or alcohol. Absolutely avoid the use of any kind of solvent. It is normal for there to be some discoloration of the silencer, which is the result of heat and the nature of the materials used. IT IS FORBIDDEN to modify silencers. Whatever form this may take, Belgrove Sp. z o.o. declines any responsibility for defects, problems, or malfunction, arising from the use of any product which has been modified or tampered with.
We suggest the fitting to be made by professionals LeoVince 14387E LV
One EVO Slip On Exhaust - Figure 1