FORTIN 80961 Mazda RX-8 2010 Standard-Key Remote Starters and Alarm Systems Installation Guide

FORTIN 80961 Mazda RX-8 2010 Standard-Key Remote Starters and Alarm

Systems

Product Information

Product Usage Instructions

If the Vehicle is Not Equipped with Functional Hood Pin:
To add the firmware version and options, use either the Flash Link Updater or Flash Link Mobile tool, sold separately.

Hood Pin Installation:
If the vehicle can be remote started with the hood open, the hood pin switch (included) must be installed. Set function A11 to OFF.
WARNING: This module must be installed by a qualified technician. A wrong connection can cause permanent damage to the vehicle.

Wiring Connections

Note: Cut the loop for automatic transmission mode.
Optional: Back view. 8-pin white connector at steering.
Optional: Back view. 4-pin green connector at transponder.

MANDATORY INSTALL
HOOD PIN
HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) A11
MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

SECURITY STICKER
WARNING
Included
Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

DESCRIPTION

AUTOMATIC TRANSMISSION WIRING CONNECTION

MANUAL TRANSMISSION WIRING CONNECTION

KEY BYPASS PROGRAMMING PROCEDURE 1/2

Make sure to have two valide vehicle кеу.

Press and hold Insert the programming button: the 6-Pin Main connector. The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.

Release the programming button when the LED is RED. If the LED is not solid RED disconnect the 6 Pin connector (Main-Harness) and go back to step 1.

Insert the required remaining connectors.

Turn the first functional key to the ON/RUN position. Wait 3 seconds or until the security light turns OFF.
CAUTION: The following step must be completed within 5 seconds. Otherwise disconnect all connectors and go back to step 1.

Turn the ignition to the OFF position and remove the first key. Wait 3 seconds.

Turn the second functional key to the ON/RUN position. Wait 3 seconds or until the security light turns OFF.

Turn the ignition to the OFF position and remove the second key.
CAUTION: The following step must be completed within 5 seconds. Otherwise disconnect all connectors and go back to step 1.

AUTOMATIC TRANSMISSION

Activate the remote starter.

MANUAL TRANSMISSION

Press and hold the programming button until the LED flashes once than release the programming button. The RED LED will flash once (1x). Using a jumper wire, apply power (12v) to the vehicle’s ignition1.

The RED LED will flash rapidly ten (10) times and after the BLUE LED will flash rapidly. If the LED is solid RED disconnect the 6 Pin connector (Main- Harness) and go back to step 1.

MANUAL TRANSMISSION
Remove the jumper.

The BLUE LED will turn off.

Manual transmission: Remove the jumper.
The module is now programmed. Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

DCRYPTOR PROGRAMMING PROCEDURE

Parts required (not included)
1x FLASH LINK UPDATER,
1x FLASH LINK MANAGER
SOFTWARE | PROGRAMME
Microsoft Windows Computer with Internet connection
1x FLASH LINK MOBILE
1x FLASH LINK MOBILE APP
Smartphone Android or iOS with Internet connection
(Internet provider charges may apply)

BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.

Press and hold Insert the programming button: the 6-Pin Main connector. The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.

Release the programming button when the LED is RED.

If the LED is not solid RED disconnect the 6 Pin connector (Main-Harness) and go back to step 1.

Insert the required remaining connectors.

Press and release the programming button once (1x). The RED LED will flash once.

Turn the Ignition to the ON/RUN position. WAIT the RED LED will turn OFF.  The YELLOW LED will turn on.

Turn the Ignition to the OFF position. WAIT the YELLOW LED will turn OFF.

KEY BYPASS PROGRAMMING PROCEDURE 2/2

Turn the Ignition to the ON/RUN position. The RED and YELLOW LEDs will alternate.

Turn the Ignition to the OFF position.

Disconnect all connectors and after the 6-Pin (Main-Harness) or the 4-Pin Data-link connector.

Microsoft Windows Computer with  Internet connection*

Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.

• Parts required (not included)

Smartphone* (Internet provider  charges may apply)

AFTER DCRYPTOR PROGRAMMING COMPLETED Go back to the vehicle and reconnect the 6-Pin (Main-Harness) or the 4-pins (Data-Link) connector and after all the remaining connector.
The module is now programmed.

REMOTE STARTER  ALARM  VERIFICATION
Test  the remote  starter. Remote start  the vehicle.

REMOTE STARTER FUNCTIONALITY

MANUAL TRANSMISSION: READY MODE
BY DEFAULT

CHOICE 2

CHOICE 3

TAKE OVER AUTOMATIQUE TRANSMISSION

REMOTE STARTER PROGRAMMING
PROCEDUREREFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.

Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.
Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>