FORTIN 63791 Mazda 5 2007 Standard-Key Remote Starters and Alarm Systems Installation Guide

FORTIN 63791 Mazda 5 2007 Standard-Key Remote Starters and Alarm Systems

Product Information

Product Usage Instructions

Program Bypass Option

If the vehicle is not equipped with a functional hood pin, follow these steps:

1. Use the FLASH LINK UPDATER or FLASH LINK MOBILE tool to add the firmware version and options (sold separately).
2. Program the bypass option by setting function A11 to OFF.

Note: The installation of safety elements is mandatory. The hood pin is an essential security element and must be installed. This module must be installed by a qualified technician. A wrong connection can cause permanent damage to the vehicle.

Description

Parking Lights Harness

Connect the following wires:

• (-) Parking Lights
• OBD-II connector (~) CAN HIGH
• OBD-II connector (~) CAN LOW

Ignition Harness

Connect the following wires:

• (+) 12V
• (+) ACCESSORY
• (+) STARTER
• (+) IGNITION
• (-) LOCK
• (-) UNLOCK

At Brake Switch

Connect the following wire:

• (+) FOOT BRAKE

At Ignition Barrel

Connect the following wires:

• (~) RX
• (~) TX

HOOD PIN CONTACT CAPOT

Connect the following wires:

• A14 (-) HOOD
• A14 (-) HAND BRAKE
• IN RS8 IN RS9 A12 (+/-) TACHOMETER
• IN RS12 (+) FOOT BRAKE
• A8 (-) GROUND OUT WHILE RUNNING OUT RS14
• A5 (-) TRUNK IN RS15
• A4 (-) DOOR IN RS16
• (-) UNLOCK OUT RS17
• (-) LOCK OUT RS18

Data-Link

Always required with data-link:

• RS7 OUT STARTER (+)
• RS6 IN/OUT IGNITION (+)
• RS5 OUT ACCESSORY (+)
• RS3 OUT PARKING LIGHTS (-)
• RS2 IN 12V BATTERY (+)
• RS1 Ground | Masse (-)

Not required with data-link:

• RS13 (+) FOOT BRAKE
• RS17 (-) UNLOCK
• RS18 (-) LOCK

Wiring Diagram

Vehicle functions supported in this diagram (functional if

MANDATORY INSTALL

HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.

THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

DESCRIPTION

AUTOMATIC TRANSMISSION WIRING CONNECTION

MANUAL TRANSMISSION WIRING CONNECTION

PROGRAM.1 KEY BYPASS PROGRAMMING PROCEDURE

BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE

PROGRAMMING PROCEDURE

1. Press and hold the programming button:
   Connect the 4-PIN Data-link harness (Black connector).
   The Blue, Red, Yellow and Blue & Red LEDs will alteratively illuminate.

2. Release the programming button when the LED is BLUE.
   If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1.

3. Insert the required remaining connectors.

4. Turn the key to the Ignition ON/RUN position.
   The BLUE LED will flash rapidly.

5. Turn the key to the OFF position.
   The BLUE LED will tum off.

6. REMOTE STARTER

7. Disconnect the 4-Pin (DataLink) connector and after all the remaining connector.

8. Press and hold the programming button:
   Connect the 4-PIN Data-link harness (Black connector).
   The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate

9. Release the programming button when the LED is RED.
   If the LED is not solid RED disconnect the 4 Pin connector (Data-Link) and go back to step 1.

10. Insert the required remaining connectors.

11. Press and release the programming button once (1x).
    The RED LED will flash once.

12. Turn the key to the Ignition ON/RUN position.
    WAIT the RED LED will turn OFF.
    The YELLOW LED will turn on.

13. Turn the key to the OFF position.
    WAIT the YELLOW LED will turn OFF.

14. Turn the key to the Ignition ON/RUN position.
    The RED and YELLOW LEDs will alternate.

15. Turn the key to the OFF position.

PROGRAM. 2

1. Press and hold the programming button:
   Connect the 4-PIN Data-link harness (Black connector).
   The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate

2. Release the programming button when the LED is RED
   If the LED is not solid RED disconnect the 4 Pin connector (Data-Link) and go back to step 1.

3. Insert the required remaining connectors.

4. Turn the first functional key to the Ignition ON/RUN position.
   Wait 3 seconds.

5. Turn the key to the OFF position.
   Remove the first key.

6. Turn the second functional key to the Ignition ON/RUN position.
   Wait 3 seconds.

7. Turn the key to the OFF position.

8. Press and hold the programming button until the LED flashes once.
   The RED LED will flash once (1x).
   Release the programming button.

9. The RED LED will flash rapidly ten (10) times.

If the LED is solid RED disconnect the 4 Pin connector (Data-Link) and go back to step 1.

Manual transmission: Remove the jumper.

The module is now programmed.
Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING

TECH SUPPORT

Tél: 514-255-HELP (4357) 1-877-336-7797
ADDENDUM GUIDE

www.fortinbypass.com

References

• Remote Car Starters, Car Alarms, Immobilizer Bypass and Connected Vehicle Solutions | Fortin Electronic Systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>