FORTIN THAR-CHR5 EVO-ALL Plug and Play Harness Instruction Manual
- June 13, 2024
- FORTIN
Table of Contents
THAR-CHR5
THARNESS INSTALLATION
INSTALLATION HARNAIS
ADDENDUM – SUGGESTED WIRING CONFIGURATION
HARDWARE VERSION
MINIMUM 6
FIRMWARE VERSION
74.[38] CHRYSLER
To add the firmware version and the options, use the
FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
Program bypass option:
UNIT OPTION | DESCRIPTION |
---|---|
C1 | OEM Remote status (Lock/Unlock) monitoring |
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:
A11 | Hood trigger (Output Status). |
---|
Program bypass option
(If equiped with OEM alarm):
D2 | Unlock before / Lock after (Disarm OEM alarm) |
---|
Parts required (Not included)
1X Fuse
1X THAR-CHR5
NOTES 12V BATTERY | 12V BATTERIE
ATTENTION THE T-HARNESS CURRENT IS LIMITED AT 10 AMP MAXIMUM.
If a parking lights (+) wire is use : that require more than 10Amp. Connect
the remote-starter’s power directly to the vehicles battery with the
appropriate fuse.
Some remote starters can not be powered through Data-Link. In these cases
connect the remote starter’s fused 12V power wire directly to the T-Harness.
MANDATORY INSTALL
* HOOD PIN HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE
VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
Notice: the installation of safety elements are mandatory. The hood pin
is an essential security element and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION
CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
This guide may change without notice. See
www.fortin.ca for latest version.
WIRING CONNECTION
PROGRAMMING PROCEDURE
Press and hold the programming button:
Connect the 4-PIN Data-link hamness (Black connector). +The Blue, Red, Yellow
and Blue & Red LEDS will alternatively iluminate.
Release the programming button when the LED is BLUE. Ifthe LED s not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1.
Insert the required remaining connectors.
Turn the key to the Ignition ON/RUN position.
+The BLUE LED will flash rapidy.
Turn the key to the OFF position. +The BLUE LED will flash rapidy.
The module is now programmed.
Use the remote of the remote: starter or security system to test all of the
supported features to ensure proper programming.
Notice: Updated Firmware and Installation Guides Updated firmware and
installation guides are posted on our web site on a regular basis. We
recommend that you update this module to the latest firmware and download the
latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit
before connecting to it. Only a computer safe logic probe or digital
multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no
liability or responsibility whatsoever pertaining to the accuracy or currency
of the information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualified technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest
version.
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>