FORTIN THAR-CHR5 EVO-ONE Plug and Play Harness Instruction Manual

June 13, 2024
FORTIN

FORTIN THAR-CHR5 EVO-ONE Plug and Play Harness Instruction Manual
Plug and Play Harness

| Vehicle functions supported in this diagram (functional if equipped)
---|---
VEHICLE| YEARS| Immobilizer bypass| T-Harness available (sold separately)| Lock| Unlock| Arm| Disarm| Hatch (open)| Trunk (open)| RAP Disable| Tachometer| Door Status| Trunk Status| Hand-Brake Status| Foot-Brake Status| OEM Remote monitoring| R.S.  OEM  remote Stand Alone compatible
CHRYSLER
200| 2011-2014| | | | | | | | | | | | | | | |
Sebring (Sedan & Convertible)| 2008-2010| | | | | | | | | | | | | | | |
DODGE
Avenger| 2008-2014| | | | | | | | | | | | | | | |

HARDWARE VERSION
7 MINIMUM

BYPASS
FIRMWARE VERSION
74.[38]

MITSUBISHI MINIMUM

To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool,

Program bypass option

**** Program bypass option: UNIT OPTION DESCRIPTION
DESCRIPTION C1 OEM Remot  status (Lock/Unlock
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN: A11 **OFF
NON** Hood trigger (Output Status).
Program bypass option (If equiped with OEM alarm): D2 Unlock before / Lock

after (Disarm OEM alarm)
**** Program remote starter option:| FUNCTION| | DESCRIPTION
---|---|---|---
Program remote starter option for R.S. OEM REMOTE STAND ALONE:| 31| 4| (+) Parking Light (E1) (+) Accessory (E2)
38| 2| Enable Press 3x Lock to remote start with the OEM remote.

Parts required (Not included)
1X Fuse

MANDATORY INSTALL

HOOD NON PIN


HOOD STATUS
: THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OF A11 OFF

SECURITY STICKER

Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.

WARNING
Included
THIS MODULE MUST BE INSTALLED BY A  QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

This guide may change without notice. See www.fortin.ca for latest version.

WIRING CONNECTION
IF OUTPUT E1 IS USED TO POWER THE PARKING LIGHTS, THEN MAKE SURE TO CONNECT A POWER SOURCE TO TERMINAL E3 THAT CAN SUPPORT 10A MINIMUM
Waring Connection
2 Driver kick panel
3 Driver kick panel
1 Vehicle transponder connector\ Back view

Warning IconCAUTION
TAKE CARE WHEN DISCONNECTING THE HARNESS FROM THE IMMOBILISER CONNECTOR. IT IS VERY FRAGILE AND CAN EASIL
Using Instruction

KEY BYPASS PROGRAMMING PROCEDURE

  1. Press and hold Connect the programming button: the 6-PIN Main harness (White connector)
    The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate
    Using Instruction

  2. Release the programming button when the LED is BLUE.
    If the LED is not solid BLUE the 6-Pin connector (Main-Harness) and go back to step1. disconnect
    Using Instruction

  3. Insert the required remaining connectors.
    Using Instruction

  4. Turn the key to the Ignition ON/RUN position
    The BLUE LED will flash rapidly
    Using Instruction

  5. Turn the key to the OFF position
    The BLUE LED will flash rapidly
    Using Instruction

  6. Press the LOCK button on the vehicles OEM remote.

  7. Press and release the programming button on the once
    Using Instruction

The BLUE LED will turn off
Using Instruction
The module is now programmed.
Like Icon Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING
Programming

Module lab
Module lab
Notice:
Updated Firmware and Installation Guides Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

Contact IconTECH SUPPORT
Tél: 514-255-HELP (4357) 1-877-336-7797


ADDENDUM GUIDE
WEB UPDATE INTERNET www.fortinbypass.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

FORTIN User Manuals

Related Manuals