FORTIN 80471 2017 Mazda 5 Remote Starters Regular Key And Alarm Systems Installation Guide

REGULAR INSTALLATION
REV.: 20220107
Guide # 80471

80471 2017 Mazda 5 Remote Starters Regular Key And Alarm Systems

VEHICLE

ADDENDUM – SUGGESTED WIRING CONFIGURATION

YEARS:2011-2017

1. 2KEY Programming
2. 1KEY Programming

• Immobilizer bypass
• Lock
• Unlock
• Arm
• Disarm
• Parking Light
• Tachometer
• Door Status
• Trunk Status
• Hand-Brake Status
• Foot-Brake Status

“Vehicle functions supported in this diagram (functional if equipped)

FIRMWARE VERSION VERSION LOGICIELLE 71.[44] FORD MINIMUM To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.

Program bypass option
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:

Contact de capot (état de sortie).

MANDATORY INSTALL

• HOOD PIN CONTACT DE CAPOT HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

A11
Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

This guide may change without notice. See www.fortin.ca for latest version.

DESCRIPTION

AUTOMATIC TRANSMISSION WIRING CONNECTION

MANUAL TRANSMISSION WIRING CONNECTION

KEY BYPASS PROGRAMMING PROCEDURE 2/3

Make sure to have two valide vehicle key.

1. Press and hold Insert the programming button:
   the 4-Pin (Data-Link) connector.
   The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.

2. Release the programming button when the LED is RED.
   If the LED is not solid RED disconnect the 4-Pin connector (Data-Link) and go back to step 1.

3. Insert the required remaining connectors.

4. Turn the first functIonal key to the ON/RUN position.
   Wait 3 seconds or until the security light turns OFF.

5. CAUTION The following step must be completed within 5 seconds.
   Otherwise disconnect all connectors and go back to step 1.
   5 sec. max
   Turn the ignition to the OFF position and remove the first key.
   Wait 3 seconds.

6. Turn the second functIonal key to the ON/RUN position.
   Wait 3 seconds or until the security light turns OFF.

7. Turn the ignition to the OFF position and remove the second key.

8. AUTOMATIC TRANSMISSION
   Activate the remote starter. MANUAL TRANSMISSION**** Press and hold the programming button until the LED flashes once than release the programming button.The RED LED will flash once (1x).

9. Using a jumper wire, apply power (12v) to the vehicle’s ignition1.

10. The RED LED will flash rapidly ten (10) times and after the BLUE LED will flash rapidly.If the LED is solid RED disconnect the 6 Pin connector (Main-Harness) and go back to step 1.

11. MANUAL TRANSMISSION
    Remove the jumper.

12. The BLUE LED will turn off. Manual transmission:
    Remove the jumper.
    The module is now programmed.
    Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.
    This guide may change without notice. See www.fortin.ca for latest version.

DCRYPTOR PROGRAMMING PROCEDURE

Parts required (not included)

FLASH LINK UPDATER,
FLASH LINK MANAGER SOFTWARE | PROGRAMME
Microsoft Windows Computer with Internet connection Ordinateur Microsoft Windows avec connection Internet

FLASH LINK MOBILE
FLASH LINK MOBILE APP
Smartphone Android or iOS with Internet connection (Internet provider charges may apply)
BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.

1. Press and hold Insert the programming button:
   the 4-Pin (Data-Link) connector.
   The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.

2. Release the programming button when the LED is RED.

3. Insert the required remaining connectors.

4. Press and release the programming button once (1x).
   The RED LED will flash once.

5. Turn the Ignition to the ON/RUN position.
   WAITthe RED LED will turn OFF.
   The YELLOW LED will turn on.

6. Turn the Ignition to the OFF position.
   WAITthe YELLOW LED will turn OFF. KEY BYPASS PROGRAMMING PROCEDURE 2/2
   

7. Turn the Ignition to the ON/RUN position.
   The RED and YELLOW LEDs will alternate.

8. Turn the Ignition to the OFF position.

9. Disconnect all the connectors and after the Data-Link (4-pins) connector.

10. Microsoft Windows Computer with Internet connection
    Ordinateur Microsoft Windows avec connection Internet
    Use the tool:
    FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.Smartphone
    (Internet provider charges may apply)
    Parts required (not included)

11. AFTER DCRYPTOR PROGRAMMING COMPLETED
    Go back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.The module is now programmed.
    The module is now programmed. REMOTE STARTER / ALARM VERIFICATION Test the remote starter. Remote start the vehicle.
    
    

Notice: Updated Firmware and Installation Guides Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.

HARDWARE VERSION FIRMWARE VERSION
EVO-ALL
Date: xx-xx
INTERFACE MODULE
PATENTS PENDING US: 2007-228827-A1
Made in Canada
www.fortinbypass.com

WARNING

The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797

ADDENDUM GUIDE

www.fortinbypass.com
WEB UPDATE MISE À JOUR INTERNET

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>