FORTIN 95191 2008 Ford Taurus Regular Key Remote Starters and Alarm Systems Installation Guide

REV.: 20220127
Guide # 95191
REGULAR, THAR-FOR4 & THAR-FOR1 INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION

FIRMWARE VERSION
VERSION LOGICIELLE
71.[52] MINIMUM
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.

Program bypass option:

UNIT OPTION
OPTION UNITE| DESCRIPTION
---|---
A5| AUX.1
Par défaut with OEM alarm
AUX.1
without OEM alarm

IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:

C1| OEM Remote status (Lock/Unlock)
monitoring
---|---
A11| | Hood trigger (Output Status).

MANDATORY INSTALL

• HOOD PIN

HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

A11| | Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.| THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
---|---|---|---

DESCRIPTION

| Parts required (Not included)
---|---
WIRE TO WIRE DIAGRAM| 1x 7.5 Amp. fuse 1x fuse
2x 1Amp. Diodes (w ith OEMalarm)
1x 1Amp. Diodes (without OEM alarm)
THARNESS DIAGRAM|
THARNESS THAR-FORD4| 1x THAR-FOR4
1x 7.5 Amp. fuse 2x 1Amp. Diodes (with OEM alarm)
THARNESS THAR-FORD1| 1x THAR-FOR1 1x 7.5 Amp. fuse
2x 1Amp. Diodes (with OEM alarm)
1x 1Amp. Diodes (without OEM alarm)

T-HARNESS: 12V BATTERY

ATTENTION THE T-HARNESS CURRENT IS LIMITED AT 10 AMP MAXIMUM.
If the parking lights (+) require more than 10Amp. connect the remote- starter’s power directly to the vehicles battery with the appropriate fuse.
Some remote starters can not be powered through Data-Link. In these cases connect the remote starter’s fused 12V power wire directly to the T-Harness.

WIRING CONNECTION

THAR-FOR4 – INSTALLATION WIRING

THAR-FOR1 – INSTALLATION WIRING

KEY BYPASS PROGRAMMING PROCEDURE 1/2

2 key programming.

2 KEY REQUIRED

1. Press and hold the programming button:
   Connect the 4-PIN Data-link harness (Black connector).
   ↳ The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.

2. Release the programming button when the LED is RED.
   If the LED is not solid RED disconnect the 4 Pin connector (Data-Link) and go back to step 1.

3. Insert the required remaining connectors.

4. Turn the first functional key to the Ignition ON/RUN position.
   Wait 3 seconds.

5. Turn the key to the OFF position.
   Remove the first key.

KEY BYPASS PROGRAMMING PROCEDURE 2/2

6. Wait 3 seconds.
   Turn the second functional key to the Ignition ON/RUN position.

7. Turn the key to the OFF position.
   Remove the second key.

8. CAUTION The following step must be completed within 5 seconds.
   Otherwise disconnect all connectors and go back to step 1.
   5 sec. max
   Press and release the programming button.
   The vehicle ignition turn ON.

↳ The RED LED will flash rapidly 10x times.
Key bypass programmed.
↳ The BLUE LED will flash rapidly.
CAN-Bus programmed.
If the LED is solid RED disconnect the 4 Pin connector (Data-Link) and go back to step 1.
The vehicle ignition will turn OFF.

The module is now programmed.
Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

DCRYPTOR PROGRAMMING PROCEDURE

Parts required (not included)
FLASH LINK UPDATER,
FLASH LINK MANAGER
SOFTWARE | PROGRAMME
Microsoft Windows Computer with Internet connection Ordinateur Microsoft Windows avec connection Internet
OR

FLASH LINK MOBILE

FLASH LINK MOBILE APP

Smartphone Android or iOS with Internet connection (Internet provider charges may apply)
BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.

1. Press and hold the Insert programming button: the 4-Pin (Data-Link) connector.
   ↳  The Blue, Yellow, Red and Blue & Red LEDs will alternatively illuminate.

2. Release the programming button when the LED is RED.
   If the LED is not solid RED disconnect the 4-Pin connector (Data-Link) and go back to step 1.

3. Insert the required remaining connectors.

4. Press and release the programming button once (1x).
   ↳ The RED LED will flash once.

5. Turn the key to the Ignition ON/RUN position.
   ↳ The RED LED will turn OFF.
   ↳ The YELLOW LED will turn on.

KEY BYPASS PROGRAMMING PROCEDURE 2/3

6. Turn the key to the OFF position Remove the key from the ignition barrel.
   ↳ The YELLOW LED will turn OFF.
   ↳ The RED LED will turn on.

7. Turn the key to the
   Ignition ON/RUN position.
   ↳ The RED LED will turn OFF.
   ↳ The YELLOW LED will turn on.

8. Turn the key to the OFF position Remove the key from the ignition barrel.
   ↳ The YELLOW LED will turn OFF.
   ↳ The RED LED will turn on.

9. Turn the key to the Ignition ON/RUN position.
   ↳ The YELLOW LED will turn on and off.
   ↳ The RED LED will turn OFF.
   ↳  WAIT, the BLUE LED to flash rapidly.

10. Turn the key to the OFF position Remove the key from the ignition barrel.
    ↳ The RED and YELLOW LEDs will alternate.

KEY BYPASS PROGRAMMING PROCEDURE 3/3

11. Disconnect all the connectors and after the Data-Link (4-pins) connector.

12. Microsoft Windows Computer with Internet connection*

Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.

Smartphone (Internet provider charges may apply)
Parts required (not included) 13. AFTER DCRYPTOR PROGRAMMING COMPLETED Go back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.

The module is now programmed.
REMOTE STARTER / ALARM VERIFICATION
Test the remote starter. Remote start the vehicle.

REMOTE STARTER FUNCTIONALITY

| All doors must be closed.
---|---
| Remote start the vehicle.
| Unlock the doors with the remote-starter remote or the OEM remote.
| Insert and Turn the key to the Ignition ON/RUN position.
| Press the brake pedal.
| The vehicle can now be put in to gear and driven.

www.fortinbypass.com
Module label

Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
Made in canada
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE
This guide may change without notice. See www.fortin.ca for latest version.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>