FORTIN THAR-NIS1 Harness for 2007 Push To Start Infiniti Installation Guide
- June 13, 2024
- FORTIN
Table of Contents
Guide # 84431
THAR-NIS1 THARNESS INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATIONNISSAN
VEHICLE
YEARS
Maxima
Push-to-Start (AT) 2009-2014
THAR-NIS1 Harness for 2007 Push To Start Infiniti
Vehicle functions supported in this diagram (functional if equipped)
- Immobilizer bypass
- T-Harness
- Lock
- Unlock
- Arm
- Disarm
- RAP Disable
- Parking Light
- Tachometer
- Door Status
- Trunk Status
- Hood Status*
- Hand-Brake Status
- Foot-Brake Status
- OEM Remote monitoring
- Push-to-Start Control
| BYPASS FIRMWARE VERSION
72.[48] MINIMUM| To add the firmware version and the options, use the FLASH
LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
---|---|---
| Program bypass option:| UNIT OPTION| DESCRIPTION
---|---|---|---
C1| OEM Remote status (Lock/Unlock) monitoring
| | D6| Push-to-Start
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:| A11 | Hood trigger
(Output Status).
| Program remote| FUNCTION| MODE| DESCRIPTION
---|---|---|---|---
32| 3| DK.Blue (GWR) Shut Down After
MANDATORY INSTALL
* HOOD PIN
HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE
CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
SECURITY STICKER
WARNING
Included
Notice: the installation of safety elements are mandatory. The hood pin and
the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION
CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
This guide may change without notice. See
www.fortin.ca for latest version.
DESCRIPTION
WIRING CONNECTION
KEY BYPASS PROGPROGRAMMING PROCEDURE 1/2
| Insert
the key in to the key port.
---|---
| Press
and hold the programming button:
Insert the 4-Pin DATA-LINK connector.
| Release
the programming button when the YELLOW LED is ON.
If the YELLOW LED is not ON solid disconnect the 4-Pin DATALINK connector and
go back to step 1.
| Insert
the required remaining connectors.
| Press
and release the programming button twice (2x).
↪The YELLOW LED will flash 2 times each second.
↪WAIT for the YELLOW LED to turn ON solid.
| Press
and release the Push-to-Start button once (x1).
↪ The RED LED will turn ON.
If the YELLOW and RED LED’s are not ON solid, press and release the PTS button
twice to turn OFF the Ignition and then press and release the PTS button once
again to turn the Accessory ON.
Repeat this step until the YELLOW and RED LED’s are ON solid.
| Press
and release the Push-to-Start button once (x1).
↪ The BLUE LED will flash rapidly.
REMOTE STARTER PROGRAMMING PROCEDURE
REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE
STARTER PROGRAMMING.
REMOTE STARTER FUNCTIONALITY
| | | |
---|---|---|---|---
All doors must be closed.| Remote start the vehicle.| Unlock the doors with
either:
• The OEM remote
• The remote-starter remote
• Or the proximity remote| Enter the vehicle with the Intelligent Key.| The
vehicle can now be put in to gear and driven.
If the vehicle is not unlocked with one of these conditions the remote-starter will shut down as soon as any door is opened.
REMOTE STARTER PROGRAMMING PROCEDURE
REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE
STARTER PROGRAMMING.
REMOTE STARTER FUNCTIONALITY
| | | |
---|---|---|---|---
All doors must be closed.| Remote start the vehicle.| Unlock the doors with
either:
• The OEM remote
• The remote-starter remote
• Or the proximity remote| Enter the vehicle with the Intelligent Key.| The
vehicle can now be put in to gear and driven.
If the vehicle is not unlocked with one of these conditions the remote-starter
will shut down as soon as any door is opened.
Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a
regular basis. We recommend that you update this module to the latest fi rmware
and download the latest installation guide(s) prior to the installation of
this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever. It is the sole
responsibility of the installer to check and verify any circuit before
connecting to it. Only a computer safe logic probe or digital multimeter
should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or
responsibility whatsoever pertaining to the accuracy or currency of the
information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualifi ed technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest
version.
Copyright © 2006-2018, FORTIN AUTO RADIO INC
ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>