FORTIN THAR-CHR7 EVO ONE Instruction Manual

: June 13, 2024
: FORTIN

Table of Contents

THAR-CHR7 EVO ONE
DESCRIPTION
THAR-CHR7 | WIRING CONNECTION
DCRYPTOR PROGRAMMING PROCEDURE
KEY BYPASS PROGRAMMING PROCEDURE 2/3
KEY BYPASS PROGRAMMING PROCEDURE 3/3
REMOTE STARTER PROGRAMMING PROCEDURE
REMOTE STARTER FUNCTIONALITY
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

THAR-CHR7 EVO ONE
Instruction Manual FORTIN THAR-CHR7 EVO ONE 1 THAR-CHR7 INSTALLATION
REV.: 20230531
Guide # 109611

THAR-CHR7 EVO ONE

ADDENDUM – SUGGESTED WIRING CONFIGURATION
Vehicle functions supported in this diagram (functional if equipped)
FORTIN THAR-CHR7 EVO ONE VEHICLE
YEARS
Immobilizer bypass

Lock
Unlock
Arm
Disarm
Parking Lights
Hatch (Open)
Tachometer
Door Status
Hood Status
Hand-Brake Status
Foot-Brake Status
OEM Remote monitoring
R.S. OEM remote Stand Alone compatible

BYPASS FIRMWARE VERSION
VERSION LOGICIELLE CONTOURNEMENT
69.[04] MINIMUM
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately. Program bypass option:

UNIT OPTION	DESCRIPTION
C1	OEM Remote status (Lock/Unlock) monitoring
D6	Push-to-Start

IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:

11	OFF	Hood trigger (Output Status).
D2		Unlock before / Lock after (Disarm OEM alarm)

Program remote starter option for R.S. OEM REMOTE STAND ALONE:

FUNCTION	MODE	DESCRIPTION
38	2	Enable : Press 3x Lock to remote start with the OEM remote.

MANDATORY INSTALL
HOOD PIN
HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED)
MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
A11……………… OFF
SECURITY STICKER
** WARNING …………………… Included
Notice:** the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

DESCRIPTION

FORTIN THAR-CHR7 EVO ONE - fig 2

THAR-CHR7 | WIRING CONNECTION

FORTIN THAR-CHR7 EVO ONE - fig 3

DCRYPTOR PROGRAMMING PROCEDURE

FORTIN THAR-CHR7 EVO ONE - fig 4 BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE. Press and hold the programming button:
Connect the 4-PIN Data-link harness (Black connector).
The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.

FORTIN THAR-CHR7 EVO ONE - fig 6 Release the programming button when the LED is BLUE. If the BLUE LED is not ON solid disconnect the 4-PIN Data-link harness (Black connector) and go back to step

Insert the required remaining connectors.

FORTIN THAR-CHR7 EVO ONE - fig 8 Do not press the brake pedal. Press the START/STOP button twice to turn ON the ignition. Press and release the programming button once (1x).
→ The BLUE LED will turn off.
→ The BLUE LED will flash rapidly (CAN1 detection).
→ The RED LED will flash rapidly (CAN2 detection). ![FORTIN THAR-CHR7 EVO ONE

fig 10](https://manuals.plus/wp-content/uploads/2023/09/FORTIN-THAR-CHR7 -EVO-ONE-fig-10.jpg)Press and release the START/STOP button once (1x) to shut off the ignition.
→ The RED and BLUE LED will continued to flash rapidly.

KEY BYPASS PROGRAMMING PROCEDURE 2/3

FORTIN THAR-CHR7 EVO ONE - fig 10 Press and release the START/STOP button once (1x) to shut off the ignition.
→ The RED and BLUE LED will continued to flash rapidly. FORTIN THAR-CHR7 EVO
ONE - fig 11 Press the UNLOCK button on the OEM remote.
→ The RED and BLUE LED will turns OFF.
→ Wait, the YELLOW LED will turns ON solide. FORTIN THAR-CHR7 EVO ONE - fig
12 Remove the battery from the OEM remote Place the OEM remote (no battery) close to the front of START/STOP button exactly as shown.
Do not move the OEM remote for the following step. FORTIN THAR-CHR7 EVO ONE -
fig 14 Press the Start/Stop button twice to turn ON the ignition.
→ The YELLOW LED will turns OFF.
→ The RED LED will turns ON. Press and release the START/STOP button once to shut off the ignition. Place the OEM remote (no battery) close to the front of START/STOP button as shown.
Do not move the OEM remote for the following step.

KEY BYPASS PROGRAMMING PROCEDURE 3/3

FORTIN THAR-CHR7 EVO ONE - fig 17 Press the Start/Stop button twice to turn ON the ignition.
→ The BLUE LED will turn off.
→ The BLUE LED will turns ON.
→ The RED and YELLOW LEDs will alternated.Press and release the START/STOP button once to shut off the ignition.
→ The RED and YELLOW LEDs will continued to alternated. FORTIN THAR-CHR7 EVO
ONE - fig 19 Reinsert the battery in the OEM remote. FORTIN THAR-CHR7
EVO ONE - fig 20 Disconnect all connectors and after the 4-PIN Data- link harness (Black connector). FORTIN THAR-CHR7 EVO ONE - fig
21 Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
*Parts required (not included)AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the the 4-PIN Data-link harness (Black connector) and after all the remaining connector.

FORTIN THAR-CHR7 EVO ONE - fig 23 The module is now programmed.
REMOTE STARTER / ALARM VERIFICATION PROCEDURE
Test the remote starter. Remote start the vehicle.

REMOTE STARTER PROGRAMMING PROCEDURE

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.
FORTIN THAR-CHR7 EVO ONE - fig 26

REMOTE STARTER FUNCTIONALITY

All doors must be closed.|
---|---
Remote start the vehicle.|
Unlock the doors with either:
• The OEM remote
• The remote-starter remote.|
Enter the vehicle with the Intelligent SmartKey.|
The vehicle can now be put in to gear and driven.|

FORTIN THAR-CHR7 EVO ONE - fig 32 Module label
Notice: Updated Firmware and Installation Guides
Updated ﬁ rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest ﬁ rmware and download the latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualiﬁ ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.