FORTIN 109621 EVO ALL Instruction Manual

THAR-CHR7 INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION
VEHICLE YEARS

109621 EVO ALL

Vehicle functions supported in this diagram (functional if equipped)
Immobilizer bypass

FIRMWARE VERSION VERSION LOGICIELLE

To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.

MANDATORY INSTALL

• HOOD PIN
  CONTACT DE CAPOT| | HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
  ---|---|---

Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
This guide may change without notice. See www.fortin.ca for latest version.
NOTES

(Output Status).
Program bypass option (If equipped with OEM alarm):| D2| Unlock before / Lock after (Disarm OEM alarm)
D6| Unlock before / Lock after (Disarm OEM alarm )

NOTES 12V BATTERY

ATTENTION THE T-HARNESS CURRENT IS LIMITED AT 5 AMP MAXIMUM.
If a parking lights (+) wire is use : that require more than 5Amp. Connect the remote-starter’s power directly to the vehicles battery with the appropriate fuse.
Some remote starters can not be powered through Data-Link.
In these cases connect the remote starter’s fused 12V power wire directly to the T-Harness.

DESCRIPTION

WIRING CONNECTION

DCRYPTOR PROGRAMMING PROCEDURE

BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE

1| | Press and hold the Insert
programming button: the 4-Pin (Data-Link) connector.
→ The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
---|---|---
2| | Release the programming button when the LED is BLUE.
If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1.
3| | Insert the required remaining connectors.
4| | Do not press the brake pedal.
Press the START/STOP button twice to turn ON the ignition.
5| | Press and release the programming button once (1x).
→The BLUE LED will turn off.
→ The BLUE LED will flash rapidly (CAN1 detection).
→The RED LED will flash rapidly (CAN2 detection).
6| | Press and release the START/STOP button once (1x) to shut off the ignition.
→ The RED and BLUE LED will continued to flash rapidly.
7| | Press the UNLOCK button on the OEM remote.
→ The RED and BLUE LED will turns OFF.
→ Wait, the YELLOW LED will turns ON solidi.
8| | Remove the battery from the OEM remote
9| | Place the OEM remote (no battery) close to the front of START/STOP button exactly
as shown.
Do not move the OEM remote for the following step.
10| | Press the Start/Stop button twice to turn ON the ignition.
→ The YELLOW LED will turns OFF.
→ The RED LED will turns ON.
11| | Press and release the START/STOP button once to shut off the ignition.
12| | Place the OEM remote (no battery) close to the front of START/STOP button as shown.
Do not move the OEM remote for the following step.
13| | Press the Start/Stop button twice to turn ON the ignition.
→ The BLUE LED will turn off.
→ The BLUE LED will turns ON.
→ The RED and YELLOW LEDs will alternated.
14| | Press and release the START/STOP button once to shut off the ignition.
→ The RED and YELLOW LEDs will continued to alternated.
15| | Reinsert the battery in the OEM remote.
16| | Disconnect all the connectors and after the Data-Link (4-pins) connector.
17| | Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE to visit the Cryptor menu.
*Parts required (not included)
18| | AFTER DCRYPTOR PROGRAMMING COMPLETED Go back to the vehicle and reconnect the 4-Pin (Data- Link) connector and after, all the remaining connector.
| The module is now programmed.
---|---
| REMOTE STARTER / ALARM VERIFICATION
Test the remote starter. Remote start the vehicle.

REMOTE STARTER FUNCTIONALITY

| All doors must be closed.
---|---
| Remote start the vehicle.
| Unlock the doors with either:
• The OEM remote
• The remote-starter remote.
| Enter the vehicle with the Intelligent Smart Key.
| The vehicle can now be put in to gear and driven.

www.fortinbypass.com
Module label

Notice: Updated Firmware and Installation Guides
Updated fi rewire and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rewire and download the latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT
Tel: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>