FORTIN 75141 EVO ALL Instruction Manual

REV.: 20230629
GUIDE # 75141
THAR-NIS1
ADDENDUM – SUGGESTED WIRING CONFIGURATION
THARNESS INSTALLATION
INSTALLATION HARNAIS

75141 EVO ALL

ONLY COMPATIBLE WITH AUTOMATIC TRANSMISSION VEHICLES.

Immobilizer bypass Contournement d’immobilisateur

| T-Harness| Lock| Unlock| Arm| Disarm| RAP Disable| Parking Light| Tachometer| Door Status| Trunk Status| Hood Status*| Hand-Brake Status| Foot- Brake Status| Push-to-Start Control| OEM Remote monitoring
NFINITI
M35 Hybrid| Push-to-Start| 2012-2013| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •
M37| Push-to-Start| 2011-2013| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •
M56| Push-to-Start| 2011-2013| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •
Q70| Push-to-Start| 2014-2017| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •
Q70L| Push-to-Start| 2015-2017| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •
FIRMWARE VERSION VERSION LOGICIELLE| To add the firmware version and the options, use the  FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
---|---
72.| [ 43 ]
NISSAN/INFINITI| MINIMUM
| Program bypass option:| UNIT OPTION OPTION UNITE| DESCRIPTION
---|---|---|---
C1| OEM Remote status (Lock/Unlock) monitoring
 | D6| Push-to-Start
Push-to-Start
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:

| A11| | Hood trigger (Output Status).
Contact de capot (état de sortie).

NOTES

| The vehicles OEM remote and SmartKey are still operable during remote start.
---|---
| Parts required (Not included)
1X Fuse
1X multimeter
1X Diode

MANDATORY INSTALL

• HOOD PIN

CONTACT
DE CAPOT

| HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED
IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
---|---

Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
This guide may change without notice. See www.fortin.ca for latest version.

WIRING CONNECTION

WIRING CONNECTION WITHOUT DATA-LINK

KEY BYPASS PROGRAMMING PROCEDURE 1/2

| Remove the valet key from the back of the OEM remote.
Remove the battery from the OEM remote.
Keep the other OEM remotes at least 3 meters (10 feet) away from the vehicle to proceed.
---|---
| Press and hold the Insert  programming button: the 4-Pin (Data- Link)connector.
 The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
| Release the programming button when the LED is YELLOW.
If the LED is not solid YELLOW disconnect the 4-Pin connector (Data-Link) and go back to step 1.
| Insert the required remaining connectors.
| Press and release the programming button three (3x) times.
 The YELLOW LED will flash 3 times each second.
 WAIT for the YELLOW LED to turn ON solide.
| Place the OEM remote (no battery) close to the front of Start/StOP BUTTON Exactly as shown.
Transponder is located behind the logo.

| Press and release the foot-brake pedal.
 The RED LED will turns ON.
 The YELLOW LED turns OFF

Wait until the message ”press brake” disappears.
(This may take up to 12 seconds).

| Hold the OEM remote close to the front of START/STOP button Press and release the foot-brake pedal.
 The RED LED is ON.
 The BLUE LED turns ON.
If the BLUE LED flash rapidly, wait until the LED turns OFF.
| Press the START/STOP button twice to turn ON the ignition.
 The BLUE LED will Flash rapidly.
 The RED LED will turns OFF.
| Press the START/STOP button once to turn OFF the ignition.
 Wait until the BLUE LED flash slowly.
| Disconnect all the connectors and after the Data-Link (4-pins) connector.
| Use the tool: FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
| AFTER DCRYPTOR PROGRAMMING COMPLETED Go back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.
| REMOTE STARTER

REMOTE STARTER FUNCTIONALITY

If the vehicle is not unlocked with one of these conditions the remote-starter will shut down as soon as any door is opened.

Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE

References

• Remote Car Starters, Car Alarms, Immobilizer Bypass and Connected Vehicle Solutions | Fortin Electronic Systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>