Mitzi H689704 Elsa Textured White 4 Light Pendant Installation Guide

Mitzi H689704 Elsa Textured White 4 Light Pendant

Product Information

This product is an Elsa H689704 fixture from Hudson Valley Lighting Group. It is designed for installation and usage in indoor spaces.

Product Usage Instructions

1. Feed the wire through the stem (L) and twist it tightly onto the fixture assembly (N). Add additional stems until the desired hanging height is achieved.
2. Attach the nipple (G) onto the stem (L) and insert the check ring (H) onto the nipple (G). Attach the canopy (I) on top of the stem (L) and secure it using hex nuts (K) and tooth washer (J).
3. Pull the wire out from the junction box and install the mounting plate (A) onto the junction box using the mounting screws (B). The junction box must be securely mounted to the building structure. Thread the studs (C) onto the mounting plate (A) and adjust their threads so that 136 of threads extend beyond the canopy (I). Secure them using small hex nuts (D).
4. Trim off the excess wire to a minimum of 6 beyond the stem (L) and strip each wire 85.
5. Attach the ground wire (green) to the ground inside the outlet box (generally green or bare copper wire) or the ground screw (E) on the mounting plate (A). Never connect the ground wire to the hot wire as it could result in serious injury or death.
6. Connect the white fixture lead to the neutral (generally white) wire in the outlet box. Fasten the wires together with a wire nut (F). Starting 1 inch below the wire nut, tightly wrap the connection with electrical tape to seal the end of the fastener. Ensure there are no exposed wires or strands that could cause a dangerous short circuit.
7. Connect the black fixture leads to the hot (generally black) wire in the outlet box. Fasten the joined wires same as the previous step. Never reverse hot and neutral wires as it could result in serious injury or death.
8. Push the wires back into the junction box. Lift up the canopy (I) up to the ceiling and secure it with barrel nuts (M).
9. Screw the bulb (O) into the socket of the fixture assembly (N). This fixture is rated for a 60-watt Type B lamp (G16.5 recommended). Do not exceed the recommended wattage.
10. Finally, restore power to the outlet at the breaker or fuse box.

For more information and replacement parts, visit www.hvlgroup.com.

Precautions

WARNING/CAUTION

• DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
• TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
• CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
• UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
• PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.

FIXTURE INSTALLATION

1. Feed the wire through the STEM (L) and twist tightly onto the FIXTURE ASSEMBLY (N). Keep adding additional stems until your desired hanging height is met.
2. Attach the NIPPLE (G) onto the STEM (L) then insert the CHECK RING (H) onto the NIPPLE (G). Attach the CANOPY (I) on top of the STEM (L), and secure using HEX NUTS (K) and TOOTH WASHER (J).
3. Pull the wire out from the junction box, and install the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted to the structure of the building. Thread the STUDS (C) unto the MOUNTING PLATE (A), adjust its threads so that 3 16″ of threads extend beyond the CANOPY (I), secure using SMALL HEX NUTS (D)
4. Trim off the excess wire to a minimum 6″ beyond the STEM (L) and strip each wire 58″.
5. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bare copperwire) or the GROUND SCREW (E) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT” WIRE. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
6. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (F). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT.
7. Connect the black fixture leads to the hot (Generally black) wire in the outlet box. Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
8. Push the wires back into the junction box. Lift up the CANOPY (I) up to the ceiling, and secure with the BARREL NUTS (M).
9. Screw the BULB (O) into the SOCKET of the FIXTURE ASSEMBLY (N). THIS FIXTURE IS RATED FOR 60 WATTS TYPE B LAMP (G16.5 RECOMMENDED). DO NOT EXCEED THE RECOMMENDED WATTAGE?
10. Restore power to the outlet at the breaker or fuse box.

www.hvlgroup.com

References

• Hudson Valley Lighting Group

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>