COOLON STELLAR-500-MP Series STELLAR Luminaire 522mm with Mounting Bracket Instruction Manual
- June 13, 2024
- COOLON
Table of Contents
STELLAR-500-MP Series STELLAR Luminaire 522mm with Mounting Bracket
Instruction Manual
STELLAR INDUSTRIAL LED MANUAL
STELLAR-500-MP Series STELLAR Luminaire 522mm with Mounting Bracket
STELLAR Luminaire with Mounting Bracket
Technical Specification
| POWER| VOLTAGE IN| IP/IK RATING| OPERATING TEMP.
---|---|---|---|---
STELLAR-500-MP230| 520W Max| 100 – 240VAC 50/60Hz 127 – 250VDC| IP66 / IK09|
-20 to +60°C
STELLAR-500-MP415| 520W Max| 277 – 440VAC 50/60Hz 352 – 500VDC| IP66 / IK09|
-20 to +50°C
MOUNTING BRACKET INSTALLATION
Note
The mounting bracket allows the STELLAR high bay luminaire to be installed on
angled surfaces between 0° and 45°.
Luminaire should remain perpendicular to the ground. It is also recommended to
use a safety lanyard installed in 1 of 4 suspension points.
Step 1
Mount the luminaire with mounting bracket to appropriate location using 2x M12
bolts or 2x 1/2” (12.7mm) bolts. Bolts not supplied by Coolon.
Step 2
Adjust the angle of the luminaire and once done, tighten the bolts on both
sides until the luminaire is fully locked in thedesired position.
ATTENTION
- Length and structural grade of fasteners to be determined by installer.
- Corrosion resistant fasteners recommended.
Customers must select an appropriate method and material for the mounting of
luminaires/equipment.
Avoid mixing materials which may lead to premature equipment failure or
insecure mounting due to corrosion or accelerated wear and tear.
Customers should account for environmental factors such as temperature, wind,
vibration, shock, impact, etc. when identifying appropriate mounting.
A periodic inspection and maintenance plan should be established in accordance
with environmental and other relevant factors affecting the long term
luminaire/equipment operation and secure mounting.
A secondary fall arrest kit is recommended for all suspended
luminaires/equipment.
SUSPENSION MOUNTING INSTALLATION
Step 1
To prepare the STELLAR high bay for suspension mounting, remove the bolts on
both sides of the luminaire and remove the mounting bracket.
Step 2
Suspend the luminaire at the 4x suspension points as marked on the lifting
bracket. It is recommended to use a safety lanyard.
ATTENTION
- Suspension hardware (chains, shackles, carabiners and safety lanyard) not supplied by Coolon.
- Suspension hardware grade (structural grade certified) to be determined by installer. MUST be suitable for contact with SS316.
- Minimum load recommended per chain: 100kg (certified).
STELLAR-500-MP230 WIRING
Cable glands not included.
Size: M25 x 1.5.
230VAC nominal input voltage.
STELLAR-500-MP415 WIRING
Cable glands not included.
Size: M25 x 1.5.
415VAC nominal input voltage. Use any 2 phases and connect to A and N.
IMPORTANT
Primary use: commercial and industrial applications.
- Read through this manual before installation
- Handle the product with care
- Class I products must be grounded
- The product must be installed by a suitably qualified person
- Do not stare at operating lamp, may be harmful to the eyes
- Turn OFF the power before installation and maintenance
- Make sure the product is securely installed
- The housing might become hot after operation
- Keep optical face clean
www.coolon.com.au
support@coolon.com.au
aus. 1300 287 533
intl. +613 8681 3633
www.coolon.com.au
As a matter of continual improvement, the requirements and recommendations in
our manuals evolve to reflect new industry requirements and the latest feedback
from the field.
The Coolon team is working hard to ensure optimal product operation and the
safety of all users, please check our website periodically to ensure you are
up to date with the latest information.
Product must be installed by a suitably qualified person. All documentation is
subject to change without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>