COOLON 10 DC Plume LED Lighting Installation Guide
- June 1, 2024
- COOLON
Table of Contents
COOLON 10 DC Plume LED Lighting
Specifications:
- Dimensions with Ball Joint Mounting Bracket: 153mm x 14mm x 50mm
- Ball Joint Mounting Bracket Rotation: 131mm
- Packaging Dimensions: 260mm x 290mm x 90mm
- Packaged Weight: 1.1kg (contents can vary)
Product Usage Instructions
Wiring Diagrams (Power):
Refer to the provided wiring diagrams for power connections. Splitters and extensions can be used within specified limits.
Wiring Diagrams (Control):
- CASAMBI Installation: Plume not recommended for Classic Casambi Networks. Supports up to 249 Plumes in an evolution Casambi mesh network.
- DALI Installation: Supports expandable DALI installations. Consult the manual for detailed instructions.
- DMX Installation: Supports DMX as Casambi scene trigger. Limited by the DALI network.
Spot Visor Accessory Installation:
- Slide spot visor over spotlight body until the end stop is in contact.
- Insert screw with star washer and tighten with hex key (1.5Nm).
Ball Joint Mounting Bracket Installation:
- Pick up base plate and select 2 suitable screws, refer to the provided table for details.
- Pick up base cover and align with base plate. Slot must be parallel to base plate edge.
FAQ
- Q: Can I use extensions beyond the specified limits?
- A: It is recommended to stay within the specified limits to ensure proper functionality and safety.
- Q: How many Plumes can be connected in a DALI network?
- A: The maximum number of luminaires and input devices allowed in a DALI network is determined by the DALI master device. Consult the manual for specific details.
- Q: Is the product compatible with all types of Casambi networks?
- A: The product is not recommended for Classic Casambi Networks but supports Casambi Mesh Networks. Refer to the provided instructions for more information.
PROFILE DIMENSIONS
With Ball Joint Mounting Bracket
Ball Joint Mounting Bracket Rotation
ATTENTION
- Please observe/follow the instructions methodically.
- Please ensure the units are handled with extreme care.
- Do not remove the product from the packaging prematurely. Only remove from packaging when ready for installation.
- Failure to observe installation instructions and handling will void the warranty of the product.
- Fittings must be installed by a licensed electrician.
- Before installing, make sure the power supply is switched off or mains cable is disconnected.
PACKAGING DIMENSIONS
WIRING DIAGRAMS (POWER)
SUPPLYSplitters and extensions can be used as required within the following limits:
- DC wiring from power supply to last unit: Up to 20 metres @48V / Up to 5 metres @24V.
- Max. # of units per run: Up to 35 Units @ 48V / Up to 30 Units @ 42V / Up to 25 Units @ 30V / Up to 10 Units @ 24V. Uncoil all cables. 10A max through current. Consult Coolon for special wiring requirements.
WIRING DIAGRAMS (CONTROL)
CASAMBI INSTALLATION
- SceneDMXcas provides scene and intensity selection for up to 20 pre-defined Casambi scenes.
- The DMX Start Address for each SceneDMXcas is user-selectable.
- SceneDMXcas can be configured with the Casambi app.
- SceneDMXcas requires an external 12 – 24VDC Class 2 power supply.
- Please refer to SceneDMXcas documentation for detailed instructions.
SPOT VISOR ACCESSORY
-
STEP 1
Align spot visor with Plume Spotlight. Spot visor can be mounted at 0° or 90°. -
STEP 2
Slide spot visor over spotlight body until the end stop is in contact. -
STEP 3
Insert screw with star washer and tighten with hex key (1.5Nm).
BALL JOINT MOUNTING BRACKET
STEP 1
Pick up base plate and select 2 suitable screws, refer to the table below for details.
LENGTH
Dependant on installation conditions. Requirement: centre of ball head must
withstand a vertical load of 20N and torque of 2.5Nm Locate and install base
plate on wall/surface. Ensure screws are fully secured.
STEP 2
Pick up base cover and align with base plate. Slot must be parallel to base plate edge. Snap base cover onto base plate as shown.
STEP 3
Loosen the adjustment screw until bracket arms fit over the ball head stud.
STEP 4
Move/rotate spotlight to the desired position, hold tight and fasten
adjustment screw (recommended torque 10Nm
SPIKE MOUNTING
STEP 1
Install Spike Accessory to the luminaire.
STEP 2
Insert the assembly into the ground
STEP 3
Aim the spotlight to desired position, hold tight and fasten adjustment screw
(recommended torque 10Nm)
CASAMBI READY
- Casambi is designed specifically for lighting and allows the user to easily control/automate a space using their phone, tablet or wireless switch.
- For more information, please visit https://casambi.com/
- For a range of switches please visit https://casambi.com/ecosystem/ and explore the options.
For use with a tablet and smartphone, download the Casambi app and follow the easy-to-use instructions to pair with your luminaire.
- How to use Casambi for the first time
- How to create a basic scene
- How to create an animation scene
archsales@coolon.com.au aus. 1300 287 533 intl. +613 8681 3633 www.coolon.com.au
All documentation is subject to change without notice. Refer to our website for the latest information.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>