Osaki Titan-Pro 3D Cascade Massage Chair Instruction Manual

Titan Pro – 3D Cascade
MASSAGE CHAIR
OPERATION INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Thank you for purchasing this product. Before you use it, please read the Operation Instructions in detail for the correct usage of this product, especially the important safety warnings. Keep the Operation Instructions properly for future reference.
Note: Our company reserves the right to change and explain any product design without prior notice. Product colors are subject to the actual products.

Safety and Maintenance

Important Safety Warnings

• Do not allow children to touch any movable part of this product.
• Use the well-grounded power supply unit suitable for this product.
• Pull out the plug after use or before cleaning to avoid any physical injury or damage to the product.
• Operate this product as instructed in this manual.
• Do not use any parts or accessories which are not recommended.
• Do not use this product outdoors.
• Please read the Operation Instructions carefully before operation.
• Never use this product for any other purpose not listed herein.
• 20 minutes of usage each time is recommended.
• Do not use this product if the leather is broken or damaged.
• Do not use this product if the cover or leather is broken or damaged.
• Do not use this product if the radiator hole is covered or blocked.
• Do not drop anything into this product.
• Never fall asleep while using this product.
• Do not use this product if you are drunk or feel unwell.
• Do not use this product within one hour after a meal.
• Do not use this product with excessive force to avoid any injury.
• Do not carry any fragile, explosive, or combustible material in your pocket, such as a mobile phone and lighter when using the massage chair.

Operating Environment

• Do not use this product in a very moist environment such as the bathroom.
• Stop using this product immediately when the ambient temperature changes sharply.
• Do not use this product in any heavily-dusty or caustic environment.
• Do not use this product in a small space or a place without good ventilation.
• The normal room temperature ranges from 0 °C to 35 °C.
• Do not use this product in an excessively humid room such as a bathroom. Use it at a relative humidity between 20% and 80%.
• Do not use this product outdoors.
• Avoid direct sunlight.
• Keep this product away from any heat source such as a stove and air outlet of an air conditioner.
• Do not use this product during thunder or lightning weather.
• Do not use this product in dusty places.

The following populations should not use this product

• Patients with osteoporosis.
• Patients with heart disease or wearing electronic medical devices such as a pacemaker.
• People who have a fever. ·Pregnant women or women on their menstrual period.
• Patients who are injured or have a skin disease.
• When unsupervised, any children are under the age of 14 and those unconscious are not allowed to use this product.
• People who are told by their physicians to have rest or who feel unwell.
• People whose bodies are wet are forbidden to use this product.
• This product has a hot surface. Persons insensitive to heat must pay attention when using this product.

Safety Precautions

• Check whether the voltage is consistent with the specification of this product.
• Never insert or pull out the plug with a wet hand.
• Do not let water flow into this product to avoid electric shock or cause damage to this product.
• Do not pull the power cord when plugging or unplugging it. Rough handling is forbidden.
• Do not damage the wire or modify the circuit of this product.
• Do not clean live parts of this product with a wet cloth such as a power switch and plug.
• Be away from this product in case of power failure to avoid any injury if power is restored suddenly.
• Stop using this product at once while it works abnormal, and consult your local supplier.
• Stop using this product if you feel unwell, and consult your health care practitioner.
• This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of this product by the personnel responsible for their safety. Children should be supervised to ensure that they do not play with this product. ·If the power cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified staff in order to avoid hazards.

Product Service and Maintenance

• This product should be maintained by the service center designated by the manufacturer only. No user should disassemble or maintain it without permission.
• Do not forget to turn off the main power switch after usage.
• Do not use this product if the power socket becomes loose.
• If this product will be left unused for a long period of time, it is necessary to roll up the power cord of this product and store this product in a dry and dust-free environment.
• Do not store this product at a high temperature or near open flame. Avoid prolonged exposure to direct sunshine.
• Please clean this product with a dry cloth. Never use thinner, benzene or alcohol.
• The mechanical components of this product are specially designed and manufactured, so no special maintenance is needed.
• Do not use a sharp object to stab at this product.
• Do not roll or pull this product on any uneven ground. Instead, it should be lifted before moving.
• Please use this product intermittently. Do not keep it working continuously for a long period of time.

Solutions to Ordinary Malfunctions

• If the motor sounds during the operation of this product, this is the normal operation sound.
• If the controller cannot work normally, check whether the plug and the power socket are connected reliably and whether the power switch is turned on.
• If the rated working time is over, this product will automatically activate the power-off button; If this product keeps operating for a long period of time, the temperature protector will stop this product automatically.
• The product can be used again after half an hour.
• Storage Conditions ·Storage room temperature: -5 °C to 35 °C.
• Relative humidity (RH) between 20% and 80%; free of corrosive gases, and a well-ventilated room.

Safety Warning

Warning
When the leg rest of the massage chair is lifted, nobody should apply pressure on the legrest to prevent the massage chair from falling forward which will damage this product or result in personal injuries.
Warning
Before sitting on the massage chair, make sure that the massage chair manipulator does not stay in the seat cushion position to avoid discomfort to the buttocks during the body pressing down and any damage to the massage chair manipulator.
Warning
Do not remove or pull out the remote controller cable or the power cord in the standby or power-on state to avoid any damage to this product or accidental electric shock of a body part. You are advised to unplug the remote controller cable and the power cord and put them away after you use the massage chair.
Warning
When the zero-gravity lying function is enabled, be sure to check whether there is any child or pet staying or playing under the bottom of the leg rest and backrest, in order to avoid any damage to this product or physical injury.

Warning
Before using the massage chair, remove any hard objects in your pocket(s) or any jewelry carried with you (e.g. key, watch, other similar portable hard objects) to avoid any damage to this product or physical injury during the massage. Warning
Do not unplug the power cord, or directly turn off the power switch on the back of the massage chair during massage, in order to avoid any damage to this product or physical injury.
**Warning
In order to allow the calf frame and backrest frame of the massage chair to move freely, the rear of the backrest frame of the massage chair needs to keep a distance of more than 6cm from the wall, which can conveniently adjust the inclination angle of the massage chair.
Warning
The massage chair should not be used by more than one person at the same time to avoid product failure or personal injury. In addition, do not let children play on the massage chair or climb onto the lower leg, seat cushion, foot, backrest or armrest. Otherwise, accidents or injuries may be caused.
Name of Components**

1. Head Cushion
2. 3D Digital Audio
3. Upper Arm Airbag
Assembly
4. Arm Airbag Assembly
5. Controller Placement Slot
6. Controller
7. USB Socket
8. Bump Massage and Magnetic Therapy
9. Human health detection sensor
10. Seat Cushion
11. Calf Frame
12. Back Cushion| 13. Armrest Shortcut Keys (built-in voice control microphone)
14. Armrest Decoration
15. Slot for Mobile Phone
16. Armrest
17. Side Cover
18. Backrest Cover
19. LED Mood Light
20. Power Back Cover
21. Mobile Wheel
22. Power Cord and Plug
23. Fuse
24. Power Switch
25. Power Input
---|---

Function

• This product has been designed by a group of AI intelligent core message manipulators that can walk up and down, stretch back and forth, and be silent in design.
• It is designed with the function of automatic detection and micro-adjustment of shoulder position and the automatic detection function of the human body curve and massage shiatsu point to automatically adjust the stretch back and forth of the manipulator according to the detected human body curve and massage shiatsu point, making massage more humanized and scientific.
• There are six automatic massage functions, i.e. Comfort massage, Relax massage, Neck & shoulder massage, Stretch massage, Back &waist massage, and full body massage.
• There are four personalized massage functions, i.e., Massage the shoulder, Massage the back, Massage the waist & buttocks, Massage the legs & feet.
• It is provided with five manipulator message scopes for manual selection, i.e., Spot, Partial, Full, Upper, and Lower.
• It is provided with eleven manipulator massage functions for manual selection, i.e., eight massage methods such as Knead, Tap (Tap I, Tap II), Knead & Tap, Shiatsu (Shiatsu I, Shiatsu II), Grab and 3D (3D I, 3D II, 3D III, 3D IV).
• It is provided with massage adjustment functions: including five massage adjustment functions for selection, i.e., air compression force, massage intensity, massage speed, massage width and roller speed, with a total of five levels for adjustment.
• It is provided with an air compression massage function: upper arm air compression massage function (built-in 6 airbags), arm air compression massage function (built-in 8 airbags), palm air compression massage function (built-in 8 airbags), and calf air compression massage function (built-in 16 airbags), with five levels of air compression intensity for adjustment.
• It is provided with waist and calf heating functions: carbon fiber is used as a far-infrared heat source.
• Slide rail technology is adopted for lying down of the backrest frame to keep zero distance between backrest and wall, thus saving space to the greatest extent.
• The guide rail of the backrest frame adopts curved guide rail technology, which conforms to the back of the human body and makes people enjoy a massage from the head to the thigh.
• It is provided with an intelligent voice control recognition function (built-in voice control microphone beside the left armrest shortcut keys).
• The USB charging function is provided in front of the slot for the right armrest controller.
• The left armrest is equipped with an Automatic key, Voice Control Wake-up key (this key is only effective when the voice control switch in the hand controller is turned on), Calf Up key, Calf Down key, Linkage Lying key, Linkage Up key, Standby key and other shortcut keys.
• Bump massage and magnetic therapy functions are provided in the left and right palm airbag pockets.
• The front end of the right armrest is provided with the human health detection feature to detect the current human heart rate, blood oxygen saturation, and fatigue index.
• It is provided with Thai stretch massage function: the calf and backrest are lifted to form automatic lying down in a cyclic manner. At the same time, the calf air compression and the back manipulators cooperate together to massage and the legs can be stretched for a stretch massage.
• It is provided with a separate lifting adjustment function for the calf rame, zero-gravity I and zero-gravity II automatic lying angle adjustment function, and linkage lifting adjustment function for the backrest frame.
• It is provided with the sole roller massage function. A group of rollers roll to 1 massage, with five levels of speed for adjustment.
• The calf frame is provided with a retractable adjustment function. The user uses his/her foot to push out his/her calf and foot. The length for the user to stretch out his/her foot is dependent on the length of his/her calf, and the user stretches back his/her foot by spring force. It is adapted to different people’s heights.
• Music playing system, with built-in 3D digital audio in the left and right upper arms. The Bluetooth function of intelligent devices can be used for wireless connection to play music. ·The left and right armrests are equipped with LED mood lights.
• Equipped with TFT color screen hand controller.
• Automatic sit-up function when the power is off and manipulator automatic re-set function.
• The head cushion adopts two independent designs, one large and one small, which can be used according to one’s own needs to reduce the massage strength of the neck and shoulders; the head cushion can be expanded to extend to the back to reduce the strength of the back massage. It is suitable for different people to use and can be freely selected.

Introduction to the Remote Controller

1. Display screen:
   ·TFT color liquid crystal display screen displays the massage function in the operating status.

2. Standby key:
   ·Turn the massage chair on or off.

3. Menu key:
   ·Enter the main menu selection interface. Please refer to page 15 of this manual for detailed function descriptions.

4. Automatic key:
   ·Enter the automatic function mode selection interface. Please refer to page 16 of this manual for a detailed function description.

5. Up key:
   ·Navigate the Up key, select the object upward in the menu or adjust the massage position upward.

6. OK key:
   ·Confirm the selected massage function to perform confirmed massage.

7. Left key:
   ·Navigate the Left key, select the object to the left or enter the left menu.

8. Down key:
   ·Navigate the Down key, select the object downward in the menu or adjust the massage position downward.

9. Zero-gravity I key:
   ·The calf frame and backrest will be automatically adjusted to the zero- gravity I position.

10. Calf frame ascending key:
    ·According to the user’s own massage requirements, the calf frame is ascended to
    the most comfortable massage posture.

11. Calf frame descending key:
    · According to the user’s own massage requirements, the calf frame is descended to the most comfortable massage posture.

12. Zero-gravity II key:
    ·The calf frame and backrest will be automatically adjusted to the zero- gravity II
    position.

13. Pause key:
    ·Pause all currently running massage functions and press this key again to continue running all massage functions before the pause.

14. Back key:
    ·Return to the function information interface in the current operating status or
    return to the previous interface.

15. Right key:
    ·Navigate the Right key to enter the sub-menu or select the object to the right.

16. Linkage sit-up key:
    ·According to the desired message angle, the backrest frame, and the calf frame
    are adjusted for linkage sit-up at the same time to the most comfortable linkage sit-up massage posture.

17. Linkage lying key:
    ·According to the desired message angle, the backrest frame and the calf frame are adjusted for linkage lying at the same time to the most comfortable linkage lying massage posture.

Method of Usage
I. Turn on the power supply of this product:

II. Massage Function Control Operation:
·After the massage chair is powered on and off and in the standby state, (LED lamp) can be awakened by the hand controller or shortcut key (LED lamp lights up), the backrest frame and calf frame can be adjusted and voice-activated awakening can be carried out and other functions cannot be used.
2. Start massage (on/off key)

• Press the on/off key, start the massage, enter the startup screen, keep the backrest frame at the default position, lift the calf frame slightly, wait for any one of the automatic function programs to be selected and start to automatically detect the full-body shape and shoulder position. If the automatic function is not selected within 5 minutes, the massage chair will automatically shut down.
• To select a personalized program, press the “Menu” key to enter the main menu interface, and use the navigation “Up” or “Down” key to select the “Personalized Program” function and press the “OK” key to enter the personalized program selection.

Method of Usage

1). Shoulder position and body shape detection

• After any automatic function is selected, the position of the backrest frame and calf frame will be adjusted to the set angle.
• After the angle is adjusted, the massage chair automatically enters the state of automatic detection of the body shape and shoulder position (Note: If you want to skip the detection of shoulder position and body shape, you can press the “OK” key to cancel the body shape detection and start massage).

2). Shoulder position adjustment

• After detecting the shoulder position, the buzzer prompts with a “beep.” If there is any difference from the actual shoulder position, adjust to the appropriate position by pressing “Up” or “Down.” The shoulder position is adjustable in 11 gears. If there is no shoulder position adjustment within 10 seconds, it will automatically enter the massage function. If you press the “OK” key directly, you will enter the massage immediately. If the shoulder position cannot be detected, massage is performed at the default shoulder position height.
• Note: During the massage, from the information interface, you can press the “Up” key or “Down” key to select the “Shoulder Position” button, then press the “OK” key to enter the shoulder position adjustment interface, and then press “Up” key or “Down” key to adjust the shoulder position.
  

Move the massage balls downward to a suitable shoulder position

·After entering the massage program, if the shoulder position needs to be adjusted from the operation status information interface, you can directly select the “Shoulder Position” key with the “Up Key” or “Down” key, then press the “OK” key to enter the shoulder position section interface, and press the “Up” key or “Down” key to adjust the shoulder position height; Press the “Back” key to return to the previous menu, or wait for 10 seconds to automatically return to the information interface.

3). Adjustment

• After entering the massage program, if massage position adjustment is required, Press the “Menu” key on the hand controller to enter the main menu interface, select the adjustment icon with the “Up” key or “Down” key or “Left” key or “Right” key, press “OK” key to enter the adjustment function interface, and then press “Left” key or “Right” key to select the massage function to be adjusted.
• You can also directly press the “Up” key or “Down” key to select the adjustment button from the operation status information interface, and press the “OK” key to enter the adjustment interface to select the massage function to be adjusted.
• From the message position interface, if the massage position is a fixed point or local, you can directly press the “Up” or “Down” key to move the manipulator up and down for adjustment.
• From the manual program interface, if the massage position is not fixed point or local, you need to adjust the message position as a fixed point or local, then press the “Left” key to select the adjustment function and enter the massage position interface, and then press the “Up” or “Down” key to move the manipulator up or down for adjustment.

3. Pause key
·When the massage function is operating, press the “Pause” key to temporarily stop all massage functions; press the “Pause” key again to continue the massage function before the pause. If the pause lasts for more than 20 minutes, all massage functions will be automatically turned off.

4. Menu key (main menu)
·Press the “Menu” key to enter the main menu massage function selection interface, including automatic program, fatigue detection, personalized program, manual program, adjustment function, setting, etc. ·Press “Up” key or “Down” key or “Left” key or “Right” key to select the massage function, and press the “OK” key to enter the massage function selected. Press the “Back” key to return to the operation status information interface.

5. Manual program (main menu – automatic program)

• Press the “Menu” key to enter the main menu interface, and press the “Up” key or “Down” key or “Left” key or “Right” key to select the automatic program; The automatic program includes six automatic massage modes, i.e. Comfort massage, Relax massage, Neck and shoulder massage, Stretch massage, Back and waist massage and Full body massage; Note: You can directly press the “Automatic” key to enter the automatic program interface.
• Press the “Up” or “Down” key to select any of the automatic massage functions, and press the “OK” key to enter the automatic massage function selected. Press the “Back” key to return to the operation status information interface.

Method of Usage

fatigue and relax the body.
Neck& shoulder massage| According to the unique neck and shoulder massage method, through effective massage of cervical spine and scapula, neck and
shoulder pain can be relieved and neck and shoulder fatigue can
be improved.
Stretch massage| The calf frame and the backrest frame are lifted and lowered for stretching and traction of the calf and waist, effectively relieving tiredness, relieving joint soreness, and restoring vitality.
Back& waist massage| Focus on the back and waist to relieve back and waist soreness.
Full body massage| Deep massage. which can revive body vitality.

Note: If the automatic function has been selected and used, it will be displayed in the status bar of massage function. You can directly press the “Back” key to view it
6. Fatigue detection (main menu – fatigue detection)

• Press the “Menu” key to enter the main menu screen, press the “Up” key or “Down” key or “Left” key or “Right” key to select the fatigue detection icon, and press the “OK” key to pop out the fatigue detection box. At this time, do not place your finger on the fatigue detection sensor or it cannot detect.
• After entering the fatigue detection box, press the “Left” or “Right” key to select the “Yes” menu in the box and then press the “OK” key to start the fatigue detection. At this time, the finger pulp can be placed on the fatigue detection sensor and the finger should be still and not move. The fatigue detection can be completed in about 40-60 seconds and the currently measured heart rate, blood oxygen saturation and fatigue index can be displayed in the pop-up box. After 10 seconds, the system recommends executing the corresponding fatigue recovery automatic program according to the detected human body fatigue index (you can also press the “Right” key to select the “No” menu in the box, and then press the “OK” key to skip the fatigue recovery automatic program and continue to run the normal massage program). If the human body is detected to be free from fatigue, the normal massage program will run.

• After the fatigue detection is completed, select “Yes” or “No” again to select the exclusive massage program and then press the “OK” key to confirm. Press the “Back” key to return to the previous menu interface.
• If the fatigue detection is unsuccessful, you can select “Yes” again to start the detection or select “No” to cancel the fatigue detection.

Note: During the detection, you cannot move or press down hard. The body should be in a relaxed state. Otherwise, the detection data may be inaccurate.
7. Personalized program (main menu – personalized program)

• Press the “Menu” key to enter the main menu interface and press “Up” key or “Down” key or “Left” key or “Right” key to select the personalized program; under the personalized program, there are four personalized massage modes: Massage shoulder, Massage the back, Massage waist and buttocks, and Massage legs and feet.
• Press the “Up” or “Down” key to select any of the personalized massage functions and Press the “OK” key to enter the personalized massage function selected. Press the “Back” key to return to the operating status information interface.

kneading and kneading and tapping.
Massage the back| Massage with massage, tapping and other techniques, mainly on
the back, sometimes on the shoulders and waist.
Massage waist& buttocks| Massage the waist and buttocks with kneading and tapping.
Massage legs & feet| Wrap feet with an airbag + sole roller and massage the legs and
feet with a calf airbag.

8. Manual program (main menu – manual program)

• Press the “Menu” key to enter the main menu interface, press the “Up” key or “Down” key or “Left” key or “Right” key to select the manual program and press the “OK” key to enter the manual program interface.
• Manual program: including massage technique, massage position, air compression, and other massage functions. ·After entering the manual program interface, press the “Left” or “Right” key to select the sub-menu to the left or to the right and press the “Up” or “Down” key to select the desired massage function option, and press the “OK” key to confirm; press the “Back” key to return to the operation status information interface.

1). Manual program (main menu – massage technique)

• It is provided with manual massage techniques: including 11 manual massage techniques, i.e., Stop, Knead, Tap I, Tap II, Knead and Tap, Shiatsu I, Shiatsu II, Grab, 3D I, 3D II, 3D III, and 3D IV.
• After entering the manual function interface, press the “Up” key or “Down” key to select the desired manual massage technique, press the “OK” key to confirm (there are seven modes of kneading, press the “OK” key to switch in cycles), and the information interface will not be automatically returned after the technique is selected. Press the “Back” key to return to the previous level interface. After returning to the information interface, you will find that you have entered the information interface with a manual function.

Function| Massage ball adjustment|
---|---|---
Kneading| Speed.| Five levels of speed for adjustment
Five levels of width for adjustment
Five levels of 3D massage intensity for adjustment
Tapping| Speed and width.
Kneading and tapping| Speed.
Shiatsu| Speed and width.
Grab| Speed.
3D| Speed, width, and intensity.

Note: 1. In 3D massage technique mode, the width cannot be adjusted for 3D and 3D;
2. Air compression force and massage intensity are adjusted by decreasing cycle.
2). Manual program (main menu – massage position)

• Manual massage position: including Spot, Partial, Full, Upper, Lower, etc.
• After entering the manual program interface, press the “Left” key or “Right” key to select the massage position function sub-menu. Then press the “Up” or “Down” key to select the desired massage position function option, and press the “OK” key to confirm; press the “Back” key to return to the operating status information interface.

and local massage positions, adjust the massage position by “Up” key or “Down” key of ” massage position” in the “adjustment function.”
Full back| Full back massage back and forth
Upper back| Upper back massage back and forth
Lower back| Lower back massage back and forth

3). Manual program (main menu – air compression)
·Manual air compression massage: including upper body air compression and lower body air compression. ·After entering the manual program interface, press the “Left” key or “Right” key to select the air compression massage function sub-menu. Then press the “Up” or “Down” key to select the desired air compression massage function option, and press the “OK” key to turn on or off the air compression massage function; Press the “Back” key to return to the operation status information interface.

function.

4). Manual program (main menu – other)

• Other manual functions: including waist heating function, leg heating function, and sole roller function.
• After entering the manual program interface, press the “Left” key or “Right” key to select other function sub-menus. Then press the “Up” or “Down” key to select the desired other massage function option, and press the “OK” key to turn on or off the selected massage function; press the “Back” key to return to the operation status information interface

01). Manual program (other – waist heating function)

• Waist heating function: It will be warm after turning on the heating function for 3 minutes.
• After entering the manual program interface, press the “Left” key or “Right” key to select other function sub-menus. Then press the “Up” or “Down” key to select the waist heating function option, and press the “OK” key to turn on or off the waist heating function; press the “Back” key to return to the operation status information interface.

02). Manual program (other – calf heating function)

• Leg heating function: It will be warm after turning on the heating function for 3 minutes.
• After entering the manual program interface, press the “Left” key or “Right” key to select other function sub-menus. Then press the “Up” or “Down” key to select the leg heating function and press the “OK” key to turn on or off the leg heating function; press the “Back” key to return to the operating status information interface.

03). Manual program (other – sole roller)

• Sole roller function: with five levels of speed for adjustment.
• After entering the manual program interface, press the “Left” key or “Right” key to select other function sub-menus. Then press the “Up” or “Down” key to select the sole roller function option and press the “OK” key to turn on or off the sole roller function; press the “Back” key to return to the operation status information interface.

9.Adjustment function (main menu – adjustment function)

• Press the “Menu” key to enter the main menu interface, press the “Up” key or “Down” key or “Left” key or “Right” key to select the adjustment function and press the “OK” key to enter the adjustment function interface. ·Adjustment function: including adjustment functions such as massage parameters, massage position, and others.
• After entering the adjustment program interface, press the “Left” or “Right” key to select the sub-menu to the left or to the right and press the “Up” or “Down” key to select the massage function option to be adjusted, and press the “OK” key to confirm; press the “Back” key to return to the operating status information interface.

1).Adjustment function (massage parameters)

• Adjustment function (massage parameters): including air compression force, massage intensity, massage speed, massage width, and roller speed.
• After entering the adjustment function interface, press the “Left” key or “Right” key to select the message parameters sub-menu. Then press the “Up” or “Down” key
  to select any of the message parameters, and press the “OK” key to adjust the speed, width or intensity; press the “Back” key to return to the operating status information interface.

• Air compression force: five levels of intensity for adjustment.
• Massage intensity: five levels of ejection intensity of the massage machine core for adjustment.
• Massage speed: five levels of massage speed for adjustment.
• Massage width: the width can be adjusted under the massage techniques including
•  tapping, shiatsu, and knocking, with five levels for adjustment.
• Roller speed: five levels of speed for adjustment.

2). Adjustment function (massage position)

• Adjustment function (massage position): in the state of fixed point or local massage area.
• After entering the adjustment function interface, press the “Left” key or “Right” key to select the massage position sub-menu. Press and hold the “Up” key and do not release the massage manipulator to walk up; If it is released, it will stop; press and hold the “Down” key and do not release the massage manipulator to walk down. If it is released, it will stop. Press the “Back” key to return to the operating status information interface

3). Adjustment function (other)

• Adjustment function (other), the time for each adjustment is increased by 5 minutes, with a minimum of 5 minutes and a maximum of 40 minutes, cycling in turn.
• After entering the adjustment function interface, press the “Left” key or “Right” key to select other sub-menus. Press the “Up” or “Down” key to adjust the time and press the “Back” key to return to the operating status information interface.

10. Setting (main menu – setting)

• Press the “Menu” key to enter the main menu interface, press the “Up” key or “Down” key or “Left” key or “Right” key to select the setting program and press the “OK” key to enter the setting program interface.
• Setting program: including language, screen locking, intelligent voice control, equipment and other setting functions.
• After entering the adjustment program interface, press the “Left” or “Right” key to select the sub-menu to the left or to the right and press the “Up” or “Down” key to select the function option to be set, and press the “OK” key to confirm; press the “Back” key to return to the operating status information interface.

1). Setting (language)

• Setting (language): including Simplified Chinese and English.
• After entering the setting function interface, press the “Left” key or “Right” key to select the language sub-menu. Then press the “Up” or “Down” key to select the language, and press the “OK” key to confirm; press the “Back” key to return to the operation status information interface.

2). Setting (screen locking)

• Setting (screen locking): The screen locking time can be adjusted for 1-20 minutes, and the screen locking time can be increased by 1 minute, 2 minutes, 3 minutes, 4 minutes, and 5 minutes, in turn, can be increased to 20 minutes at most.
• After entering the setting function interface, press the “Left” key or “Right” key to select the screen locking sub-menu. ·Press the “Up” or “Down” key to select screen locking time, and press the “Back” key to return to the operation status information interface.

3). Setting (intelligent voice control)

• Setting (intelligent voice control): intelligent voice control massage chair.
• After entering the setting interface, press the “Left” key or “Right” key to select the intelligent voice control sub-menu and press the “OK” key to turn the intelligent voice control function on or off. Press the “OK” key to confirm; press the “Back” key to return to the operating status information interface.

4). Setting (equipment information)
·After entering the setting function interface, press the “Left” key or “Right” key to select the equipment information sub-menu to display the current equipment information, and press the “OK” key to confirm. Press the “Back” key to return to the operating status information interface.

11. Back key
·When adjusting the massage function, if you need to return to the main interface, press this key to return to the operating status information interface.

12. Zero-gravity key
·Press the “Zero-gravity key” to activate the zero-gravity adjustment function, and you can select “Zero-gravity I” or “Zero-gravity II” position according to your own needs

to the zero-gravity I position.
Zero-gravity II: the calf frame and backrest will be automatically adjusted to the zero-gravity II position.

13. Lying angle adjustment key Key

frame and release it to stop rising.
Calf frame descending key: press and hold this key to slowly lower the calf frame and release it to stop lowering.
Linkage sit-up key: press and hold this key to slowly rise the backrest frame while slowly lowering the calf frame and releasing it to stop rising of the backrest frame and lowering of the calf frame.
Linkage lying key: press and hold this key to slowly lower the backrest frame while slowly rising the calf frame and releasing it to stop lowering of the backrest frame and rising of the calf frame.

.Description of armrest shortcut keys

1. Voice Control Microphone: built-in voice control microphone.
2. Linkage Sit-up key: adjust the linkage up angle.
3. Linkage Lying key: adjust the linkage lying angle.
4. Calf Frame Up key: adjust calf frame-up.
5. Calf Frame Down key: adjust calf frame down.
6. Voice Control Wake-up key: Short press this key to wake up the voice control, long press for 3 seconds to turn on/off the voice control function.
7. Autokey: switch from/to the automatic massage function in cycles.
8. On/Off key: turn on/off the massage chair.

Linkage Sit-up key: press and hold this key to slowly raise the backrest frame while slowly lowering the calf frame and release it to stop rising of the backrest frame and lowering of the calf frame.
Linkage Lying key: press and hold this key to slowly lower the backrest frame while slowly rising the calf frame and release it to stop lowering of the backrest frame and rising of the calf frame.
Calf Frame Ascending key: press and hold this key to slowly rise the calf frame, and release it to stop rising.
Calf Frame Descending key: press and hold this key to slowly lower the calf frame and release it to stop lowering.
Voice Control Wake-up key: short press this key to wake up the voice control function, long press for 3 seconds to turn on/off this function. If no valid voice words are identified within 10 seconds, it is necessary to wake up the voice control function again (this key is only enabled when the voice control switch is on).
Auto Mode key: switch from/to the automatic massage function for each press.

IV. Voice Control Mode

• When the massage chair is turned on or in standby mode, the sound “Hi Alice” or”Hey Alice”will be produced to enable the voice control function. Alternatively, you can press the voice control button on the right armrest to enable the voice control function.
• Long press 3 seconds to turn on or off the voice control function.
• After such function is enabled successfully, the massage chair will reply “I am here”
• At this moment, once a corresponding voice control entry to be implemented is given within six seconds, the corresponding voice control function can be performed after a reply is received from the massage chair; if no correct voice control entry is given within six seconds, the voice control function automatically will be off automatically and needs to be enabled again.
• Note: When the voice control function is enabled, please speak English. The speaking speed cannot be too fast. The speech instruction should be issued according to the voice control entry.

Voice Control Entry

Entry: “1-11Alice” or ‘Hey Alice”. Answer: I am here.

No.| Voice control entry| Answer entry
1| Massage on| Answer: Ok, massage on
2| Massage close| Answer: Ok, massage close
3| Comfort Massage| Answer: Ok, comfort massage
4| Relax massage| Answer: Ok, relax massage
5| Full body massage| Answer: Ok, full body massage
6| Neck and shoulder massage| Answer: Ok, neck and shoulder massage
7| Back and waist massage| Answer: Ok, back and waist massage
8| Stretch massage| Answer: Ok, stretch massage
9| Fixed massage| Answer: Ok, fixed massage
10| Change the other mode| Answer: Ok, change the other mode
11| Go little down| Answer: Ok, go little down
12| Go little up| Answer: Ok, go little up
13| Open the air pressure| Answer: Ok, open the air pressure
14| Close the air pressure| Answer: Ok, close the air pressure
15| Up the seat position| Answer: Ok, up the seat position
16| Down the seat position| Answer: Ok, down the seat position
17| Stop adjustment| Answer: Ok, stop adjustment

V.Turn off the power and stop massage

• If the power button is pressed during a massage, it will stop all the massage functions immediately, and the backrest, the legrest, and massage chair manipulators will go back to the default positions. When the preset massage time is up, all the massage functions will be off. The backrest and the leg rest will not go back to the default positions.
• Shut off the power supply of this product, as shown in the attached figure (Power Shut-off Diagram of the Product).

1. Schematic diagram of the whole machine power turned off.
2. Schematic diagram of unplugging the whole machine wiring.
3. Schematic diagram of unplugging the power plug.

VI.Operation Instructions for Bluetooth Speaker Play

1. Enter the smart device main menu. Open “Settings” and select the “Bluetooth” option. Open “Bluetooth”, and Bluetooth will automatically “Search for a New Bluetooth Device”.
2. The smart device will search for the corresponding Bluetooth model (e.g. IMCMXXXX). Click the “Match” button. If you are asked whether to match with the device, you just select “Match” to complete matching.
3. Turn on “Music Player” in the smart device and select the song to play.

VII.lnstallation Instructions for Legrest

• After connecting the calf and the air tube on the massage chair with the wire harness, untie the fixed pipeline belt and insert the connecting part into the seat frame (Figure
• Place the round tubes on the left and right sides of the calf on the calf frame seat (Figure 2).
• Turn over the calf fixing cover to cover the round tubes on both sides of the calf (Figure 3).
• Fasten the calf on the massage chair with 2 M4 screws (1 on the left and 1 on the right). Check whether or not there is any abnormality in the up-and-down turning and whether the pipeline is folded. The calf installation is now complete (Figure 4).

VIII. Instructions for Removal and Use of Head Cushion and Backrest

• The use of the head cushion can reduce the intensity of kneading massage on the neck and shoulders. You can decide whether to use the head cushion according to your own needs (the head cushion is recommended). The backrest and the back cushion are connected by a zipper (1). The head cushion and the backrest are connected by a zipper (2).

IX.Floor Protection

• The prolonged heavy pressure on the massage chair may cause scratches on the floor. Thus, put a carpet or cushion on the floor where the massage chair is placed to avoid this damage. Note: Do not move the massage chair with its wheels on the rough ground or in a narrow space. At least two persons are required to lift it. During lifting, take the legrest sealing plate and backrest cover grooves as the acting points. (Do not lift the armrest directly.)

X.Instruction for movement
·Make sure that all the wires are pulled away from the massage chair surface; then press the backrest down to a certain angle (with the center of gravity resting on the wheels), you can push the massage chair forward with your hands, move it to a suitable position and gently restore it to the normal angle.
(Note: During movement, you must turn off the power button first and then unplug the power cord and the remote controller connection wire.)

Warning : The rear moving wheels of the massage chair are only suitable for short distance and slow movement. For long-distance transportation, please use other auxiliary moving tools to move this massage chair!

Product Specification

Model: Titan Pro – 3D Cascade
Name: Massage Chair
Rated voltage: 110-120V~ 60Hz
220-240V~ 50Hz/60Hz
Rated power: 150W
Rated time: 20min
Safety structure: Class I
Material description: PVC, PA, steel parts, electric and electron components

MATERIAL……………..
PU…………………………..
LEATHER……………………
CLOTH…………………
WOOD……………………………….

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>