COOLON PLG32 AC2 Industrial LED User Manual
- June 12, 2024
- COOLON
Table of Contents
COOLON PLG32 AC2 Industrial LED
Product Information
The AC2 Industrial LED is a fixed/stationary installation luminaire designed for commercial and industrial applications. It is not intended to be used as a hand-held work light. The product is polarity insensitive and can be connected securely with or without a plug. It is important to note that damage resulting from misuse is not covered by warranty.
The luminaire has a power consumption that varies depending on the nominal voltage. The voltage range for the product is not specified in the manual. The power factor of the AC supply should be considered during installation. The cable diameter required for installation is not mentioned, but a minimum of 40mm of free space must be available at the cable entry end to ensure proper cable placement. The luminaire comes with a 2-core cable (black and white) for exposed units.
When the product reaches the end of its life cycle, it should be disposed of following local e-waste laws and regulations. Theseproducts should not be disposed of as unsorted municipal waste and should be taken for recycling. For information on the nearest recycling point, contact the local waste authority.
For the most up-to-date information, it is recommended to periodically check the Coolon website as the product documentation is subject to change without notice.
Product Usage Instructions
- Ensure that there is a minimum of 40mm of free space away from the luminaire at the cable entry end for proper cable placement.
- Do not use the product as a hand-held work light; it is designed for fixed/stationary installation only.
- If the unit is supplied with a PLG32 – 492/32 VAC Plug, followthe installation instructions provided for connecting the plug.
- If the unit is not equipped with a plug, securely connect the wires.
- Dispose of the product in accordance with local e-waste laws or regulations. Do not treat it as unsorted municipal waste; take it for recycling.
- For any further information or updates, visit the Coolon website.
Dimension
ATTENTION
Cable entry end must have minimum 40mm of free space away from the luminaire to ensure sufficient room for cable placement. This product is designed for fixed/stationary installation, it is not designed to be used as a hand held work light. Damage sustained by the units as a result of misuse is not covered by warranty.
INSTALLATION INSTRUCTIONS
PLG32 – 492/32 VAC Plug
Units supplied with PLG32 – 492/32 VAC Plug.
WR2OS – 2 Core Cable Exposed
Units supplied with exposed 2 core cable.
Units are polarity insensitive. Units not equipped with a plug must have the wires connected securely.
Technical Specifications
- Power Consumption: 18 – 20W Typical
- Nominal Voltage: 24 VDC 30 VAC
- Voltage Range: 23 – 50 VDC 23 – 35 VAC 50Hz
- Power Factor (AC supply): 0.5
- Cable Diameter: 7.5mm
- Cable Length: 3 Metres
Once the product has reached end of life, unit is to be disposed of in accordance to local e-waste laws or regulations. Do not dispose of these products as unsorted municipal waste: take them for recycling. For information on your nearest recycling point, check with your local waste authority.
IMPORTANT
Primary use: commercial and industrial applications.
- Read through this manual before installation
- Handle the product with care
- Class I products must be grounded
- The product must be installed by a suitably qualified person
- Do not stare at operating lamp, may be harmful to the eyes
- Turn OFF the power before installation and maintenance
- Make sure the product is securely installed
- The housing might become hot after operation
- Keep optical face clean
- support@coolon.com.au
- aus. 1300 287 533
- intl. +613 8681 3633
- www.coolon.com.au.
As a matter of continual improvement, the requirements and recommendations in our manuals evolve to reflect new industry requirements and the latest feedback from the field. The Coolon team is working hard to ensure optimal product operation and the safety of all users, please check our website periodically to ensure you are up to date with the latest information. Product must be installed by a suitably qualified person. All documentation is subject to change without notice.