HQ POWER VDPLPS36BP PAR36 LED Pinsport User Manual

HQ POWER VDPLPS36BP PAR36 LED Pinsport

Introduction

To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules. If in doubt, contact your local waste disposal authorities. Thank you for buying the VDPLPS36BP! This is a DMX-controlled LED PAR36. If the device was damaged in transit, don’t install or use it and contact your dealer. Please read the manual thoroughly before bringing this device into service.

Safety Instructions

• Be very careful during the installation: touching live wires can cause life-threatening electroshocks.
• Keep this device away from rain and moisture.
• Unplug the mains lead before opening the housing.
• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
• A qualified technician should install and service this device.
• Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device against damage by leaving it switched off until it has reached room temperature.
• This device falls under protection class II. It is therefore essential that the device be earthed. Have a qualified person carry out the electric connection.
• Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.
• Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if necessary.
• Disconnect the device from the mains to clean it or when it is not in use. Handle the power cord by the plug only.
• Shields, lenses or UV screens shall be replaced if they become visibly damaged (e.g. cracks, scratches) to such extent that their effectiveness is impaired.
• Do not look directly at the light source as sensitive people may go into epileptic seizure if they do.
• Note that damage caused by user modifications to the device is not covered by the warranty.
• Keep the device away from children and unauthorized users.

General Guidelines

• This device is designed for professional use on stage, in discos, theatres, etc. The VDPLPS36BP should only be used indoors with an alternating current of max. 230VAC/50Hz.
• Lighting effects are not designed for permanent operation: regular operation breaks will prolong their lives.
• Do not shake the device. Avoid brute force when installing or operating the device.
• Select a location where the device is protected against extreme heat (see “Technical Specifications”), dust and moisture. Respect a minimum distance of 0.5m between the device’s light output and any illuminated surface.
• Use an appropriate safety cable to fix the device (e.g. VDLSC8).
• Familiarise yourself with the functions of the device before actually using it. Do not allow operation by unqualified people. Any damage that may occur will most probably be due to the unprofessional use of the device.
• Use the original packaging if the device is to be transported.
• All modifications of the device are forbidden for safety reasons.

Installation

Connecting the device

1. Power supply: 230VAC / 50Hz
2. Fuse: 5 x 20mm F1A (order code: FF1N)
3. Signal input: XLR connector connected with a DMX512 control panel.
4. Signal output: XLR connector connected with next spot.
5. DMX-address switches: Stand-alone function or DMX setting

DMX-512 Connections
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3- pin XLR input of the VDPLPS36BP. Multiple VDPLPS36BPs can be linked through serial linking. The linking cable should be two-core, screened cable with XLR input and output connectors. Please refer to the diagram at the right.

Caution: At the last fixture, the DMX cable has to be terminated with a terminator. Only use a stereo-shielded cable and 3-pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another.

Occupation of the XLR connector:

DMX-512 Chain with termination
A DMX terminator is recommended for installations where the DMX cable has to run a long distance or is in an electrically noisy environment (e.g. discos). The terminator prevents corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120Ω resistor between pins 2 and 3, which is then plugged into the XLR output socket of the last device in the chain. Please see the illustrations to the left.

Projector DMX start address selection
All DMX-controlled devices need a digital start address so that the correct device responds to the signals. This digital start address is the channel number from which the device starts to “listen” to the DMX controller. Enter the correct number and read it from the display located on the base of the VDPLPS36BP. You can use the same starting address for a whole group of devices or enter an individual one for every device. When all devices have the same address, all the units will “listen” to the control signal on one particular channel. In other words: changing the settings of one channel will affect all devices simultaneously. If you set different addresses, each device will “listen” to a separate channel number. Changing the settings of one channel will only affect the device in question. In the case of the 4-channel VDPLPS36BP, you will have to set the start address of the first unit to 1, the second unit to 5 (1 + 4), the third to 9 (5 + 4), and so on.

Use

DMX channels:

Stand-alone functions:

|
---|---
ON| OFF| Function| ON| OFF|
1,2,3| 4,5,6,7,8,9,10| Red ONLY| 1,10| 2,3,4,5,6,7,8,9| Choose 1st channel
3,4,5| 1,2,3,7,8,9,10| Green ONLY| 2,10| 1,3,4,5,6,7,8,9| Choose 2nd channel
7,8| 1,2,3,4,5,6,9,10| Blue ONLY| 1,2,10| 3,4,5,6,7,8,9| Choose 3rd channel
7,9| 1,2,3,4,5,6,8,10| 7 colours Random Function| 3,10| 1,2,4,5,6,7,8,9| Choose 4th channel
1,9| 2,3,4,5,6,7,8,10| Auto Mini Chase from

red, green to blue

| ………| ………………| By analogy, choose the

desired address

(1,2)3,9| 4,5,6,7,8,10| Slowly change colour (Speed control with the 1st and 2nd switch).|

Cleaning and Maintenance

1. All screws should be tightened and free of corrosion.

2. The housing, the lenses, the mounting supports and the installation location (e.g. ceiling, suspension, trussing)
   should not be deformed, modified or tampered with e.g. do not drill extra holes in mounting supports, do not
   change the location of the connections …

3. Mechanically moving parts must not show any signs of wear and tear.

4. The electric power supply cables must not show any damage. Have a qualified technician maintain the device.

5. Disconnect the device from the mains prior to maintenance activities.

6. Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.

7. There are no user-serviceable parts, apart from the lamp and the fuse (see “Installation”).

8. Contact your dealer for spare parts if necessary.

Technical Specifications

• Power Supply max. 230VAC / 50Hz
• Power Consumption max. 5W
• DMX channels 4 channels
• Fuse F1A, 250VAC (order code FF1N)
• Dimensions 150 x Ø130mm
• Total Weight 800g
• Max. Ambient Temperature 45°C
• Max. Housing Temperature 60°C

For more info concerning this product, please visit our website www.hqpower.eu. The information in this manual is subject to change without prior notice.

Velleman® Service and Quality Warranty
Velleman® has over 35 years of experience in the electronics world and distributes its products in more than 85 countries. All our products fulfil strict quality requirements and legal stipulations in the EU. In order to ensure quality, our products regularly go through an extra quality check, both by an internal quality department and by specialized external organizations. If, all precautionary measures notwithstanding, problems should occur, please make appeal to our warranty (see guarantee conditions).
General Warranty Conditions Concerning Consumer Products (for EU):

• All consumer products are subject to a 24-month warranty on production flaws and defective material as from the original date of purchase.

• Velleman® can decide to replace an article with an equivalent article, or to refund the retail value totally or partially when the complaint is valid and a free repair or replacement of the article is impossible, or if the expenses are out of proportion. You will be delivered a replacing article or a refund at the value of 100% of the purchase price in case of a flaw occurred in the first year after the date of purchase and delivery, or a replacing article at 50% of the purchase price or a refund at the value of 50% of the retail value in case of a flaw occurred in the second year after the date of purchase and delivery.

• Not covered by warranty:

  • all direct or indirect damage caused after delivery to the article (e.g. by oxidation, shocks, falls, dust, dirt, humidity…), and by the article, as well as its contents (e.g. data loss), compensation for loss of profits;
  • frequently replaced consumable goods, parts or accessories such as batteries, lamps, rubber parts, drive belts… (unlimited list);
  • flaws resulting from fire, water damage, lightning, accident, natural disaster, etc. …;
  • flaws caused deliberately, negligently or resulting from improper handling, negligent maintenance, abusive use or use contrary to the manufacturer’s instructions;
  • damage caused by a commercial, professional or collective use of the article (the warranty validity will be reduced to six (6) months when the article is used professionally);
  • damage resulting from inappropriate packing and shipping of the article;
  • all damage caused by modification, repair or alteration performed by a third party without written permission by Velleman®.

• Articles to be repaired must be delivered to your Velleman® dealer, solidly packed (preferably in the original packaging), and be completed with the original receipt
  of purchase and a clear flaw description.

• Hint: In order to save on cost and time, please reread the manual and check if the flaw is caused by obvious causes prior to presenting the article for repair. Note
  that returning a non-defective article can also involve handling costs.

• Repairs occurring after warranty expiration are subject to shipping costs.

• The above conditions are without prejudice to all commercial warranties.

The above enumeration is subject to modification according to the article (see the article’s manual).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>