COOLON MAYA UG TW LED Lighting Installation Guide

COOLON MAYA UG TW LED Lighting

Product Information

Specifications

• Profile Dimensions:
  • Width: 22.5mm
  • Height: 20mm
  • Depth: 3.5mm
• Mounting Options:
  • With MC-CCLIP20 Stainless Steel C-Clip
  • Recommended Rebate: 12.8mm
• Connector Dimensions:
  • Connector 2 Pin: 8.1mm x 25.8mm x 16.5mm
  • Connector 3 Pin: 8.1mm x 25.8mm x 7mm
  • Connector 4 Pin: 8.1mm x 25.8mm x 8.7mm
  • Connector 5 Pin: 13.3mm x 24.7mm x 10.7mm
  • Round Locking Connector 2 Pin: 41mm x 43.8mm
  • Round Locking Connector 3 Pin: 41mm x 43.8mm
  • Flat Connector 4 Pin: 9mm x 41.4mm x 18.9mm
  • Connector 6 Pin: 55.5mm x 59mm
• Wiring Options provided for various products.

Product Usage Instructions

Mounting Instructions:

1. Ensure you have the required clearance for installation.
2. Choose the appropriate mounting option (MC-CCLIP20 or MBR-RB-TA-BLK & MBR-RB-TB-BLK).
3. Follow the recommended rebate dimensions if using MC-CCLIP20.
4. For Type A mounting, follow the specified dimensions.
5. For Type B mounting, follow the specified dimensions.
6. Ensure a minimum screw size of 12mm for secure installation.

Connector Wiring Instructions:
Refer to the provided wiring options for different products and connect the corresponding pins/colors as instructed.

Additional Notes:
For more detailed information, please refer to the specifically used LED driver’s documentation.

Frequently Asked Questions (FAQ)

• Q: Can I use different mounting options for this product?
  A: Yes, you can choose between using the MC-CCLIP20 or the MBR-RB-TA-BLK & MBR-RB-TB-BLK mounting options based on your installation requirements.

• Q: What is the recommended clearance for full rotation of the installed product?
  A: A minimum clearance of 60mm is required for full rotation when using specific mounting options.

P20 STRIP PROFILE INSTALL ATION INSTRUCTIONS
Featured on the following products

• ALTO IP
• FORMA
• MAYA UG TW
• MAYA UG TW IP
• MULTO IP
• RATIO
• RATIO IP
• SPECTRUM RGBW
• SPECTRUM RGBW IP

PROFILE DIMENSIONS

ATTENTION

• Please observe / follow the instructions methodically.
• Please ensure the units are handled with extreme care.
• Do not remove LED strips from packaging prematurely. Only remove from packaging when ready for installation.
• Failure to observe installation instructions and handling will void warranty of the product.

MOUNTING OPTIONS

• With MC-CCLIP20
  Stainless Steel C-Clip

• RECOMMENDED REBATE
  When using MC-CCLIP20 only

With MBR-RB-TA-BLK & MBR-RB-TB-BLK
Rotating Bracket Type A & Type B

CONNECTOR DIMENSIONS

WIRING OPTIONS

Maya UG TW

Maya UG TW IP

Ratio

Ratio IP

Flat Connector 4 Pin (BROY)

Round Locking Connector 3 Pin (GBW)

Spectrum RGBW

Spectrum RGBW IP

WIRING DIAGRAM FOR TW

For more detailed information, please refer to the specifically used LED driver’s documentation.
With DRV-LN200D-D2Z2C / D2Z2D
eldoLED LINEAR drive 8A DALI DT8 Full-Colour Dimmable LED Driver / 8A DALI DT6 Full-Colour Dimmable LED Driver

With CAS-CBU-PWM4
Casambi Bluetooth Controllable 4 Channel PWM Dimmer

For more detailed information, please refer to the specifically used LED driver’s documentation.
FEMALE RJ45

With DRV-RDM-P4
DMX / RDM 4 Channel LED Driver

With DRV-RDM CV NEO-RJ45F-OC6FO05-IP65
Neo Outdoor DMX / RDM 4 Channel LED Driver

With CAS-CBU-PWM4
Casambi Bluetooth Controllable 4 Channel PWM Dimmer

STEP 1

• Before you begin installation, ensure that you understand the fitting layout required as supplied lengths may vary.
• Refer to the supplied cut sheet for length breakdowns.
• For fittings 1m or longer two installers are recommended.

WIRING

• If the fitting is wired from the back:
• It will need to wired before mounting.
• If the fitting is wired from the side:
• It will need to wired after mounting.
• Wire the fitting to the correct power supply as advised on the cut sheet.

STAINLESS STEEL C-CLIP

STEP 2

• Prepare mounting clips and screws (Ø3.5mm).
• Secure mounting clips with screws on timber or metal surface ensuring that mounting clips are positioned screw side up with spacings of 400 – 500mm.
  

STEP 3

• Lay the luminaire on top of the clips and align so all clips are centred. Starting at one end push down the fitting until you hear the clip lock into place. Continue along the profile until all clips are locked.

ROTATING BRACKET TYPE A & TYPE B

STEP 2

• Place rhomb nut in the base of the extrusion of the luminaire, ensuring that the edges of the nut are parallel with the edges of the extrusion.
• Next place the plastic aligning clip over the rhomb nut.

STEP 3
Place the edge of the bracket (with the slight lip) over the extrusion and secure the bracket to the rhomb nut using the screw provided.

STEP 4
Prepare screws (Ø4mm). Secure the other side of the bracket with screws on timber or metal surface ensuring that mounting clips are straight with spacings of 1,000mm.

STEP 5
Rotate the fitting to the desired angle and use Allen key provided to tighten bracket to secure in place.

STEP 6

• Wire the fitting to the correct power supply as advised on the cut sheet.
•  Typically supplied with AU flex and plug (1.8m long)

archsales@coolon.com.au aus. 1300 287 533 intl. +613 8681 3633

• www.coolon.com.au
• All documentation is subject to change without notice. Refer to our website for the latest information.

References

• 3633coolon.com
• Coolon LED Lighting Products - Melbourne, Australia | Coolon LED Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>