COOLON MAX MINI Compact Medium Power Linear Floodlight Installation Guide

June 12, 2024
COOLON

COOLON MAX MINI Compact Medium Power Linear Floodlight Installation Guide
COOLON MAX MINI Compact Medium Power Linear
Floodlight

PROFILE DIMENSIONS

  • Wire from side
    Dimension

  • Wire from back
    Dimension

  • Cable Gland

WIRING OPTIONS

  • 2 wires (RB) – Indoor only
    Wiring Options

  • 2.2pin Male connector – Outdoor only
    Wiring Options

  • 3 wires (RBW) – Indoor only
    Wiring Options

  • 6pin Male connector – Outdoor only
    Wiring Options

ATTENTION

  • Please observe / follow the instructions methodically.
  • Please ensure the units are handled with extreme care.
  • Do not remove LED strips from packaging prematurely. Only remove from packaging when ready for installation.
  • Failure to observe installation instructions and handling will void warranty of the product.
  • Fittings must be installed by a licensed electrician.
  • Before installing, make sure the power supply is switched off.

With MC-CCLIP
Stainless Steel C-Clip
Dimension

With MBR-RB-TA-BLK & MBR-RB-TB-BLK
Rotating Bracket Type A & Type B
Dimension

With MBR-PMAX-E-BLK & MBR-PMAX-E-WHT
Elevated Rotating Mounting Bracket
Dimension

Dimension| MC-CCLIP| MBR-RB- TA/TB| MBR-PMAX-E
---|---|---|---
A (Ø_mm) Screw outer diameter| 3.5| 4| 3.3
B (Ø_mm) Screw head clearance| 6.6| N/A| 8.8
C (mm) Screw head pocket depth| 2.5| N/A| 26.0

STAINLESS STEEL C-CLIP

STEP 1
Before you begin installation, ensure that you understand the fitting layout required as supplied fitting lengths may vary. Refer to the supplied cut sheet for length breakdowns.

  • For fittings 1 metre or longer two installers are recommended.
    Stainless Steel C-clip

Clips spaced at 300mm, refer to luminaire cut sheet for allocated quantity per fitting.

STEP 2
Prepare mounting clips and screws (Ø3.5mm). Secure mounting clips with screws on timber or metal surface ensuring that mounting clips are positioned screw side up.
Stainless Steel C-clip

STEP 3
Lay the luminaire on top of the clips and align so all clips are centred. Starting at one end push down the fitting until you hear the clip lock into place. Continue along the profile until all clips are locked.
Stainless Steel C-clip

ROTATING BRACKET TYPE A & TYPE B

STEP 1
Before you begin installation, ensure that you understand the fitting layout required as supplied fitting lengths may vary. Refer to the supplied cut sheet for length breakdowns.

  • For fittings 1 metre or longer two installers are recommended.
    Stainless Steel C-clip

Recommended number of brackets:

< 1 metre: 2 brackets
> 1 metre and <2 metres: 3 brackets
> 2m metres: 4 brackets

STEP 2
Place rhomb nut in the base of the extrusion of the luminaire, ensuring that the edges of the nut are parallel with the edges of the extrusion.
Next place the plastic aligning clip over the rhomb nut.
Stainless Steel C-clip

STEP 3
Place the edge of the bracket (with the slight lip) over the extrusion and secure the bracket to the rhomb nut
using the screw provided.
Stainless Steel C-clip

STEP 4
Prepare screws (Ø4mm). Secure the other side of the bracket with screws on timber or metal surface ensuring that mounting clips are straight.
Stainless Steel C-clip

STEP 5
Rotate the fitting to the desired angle and use Allen key provided to tighten bracket to secure in place.
Stainless Steel C-clip

ROTATING BRACKET

STEP 1
Before you begin installation, ensure that you understand the fitting layout required as supplied fitting lengths may vary. Refer to the supplied cut sheet for length breakdowns.

  • For fittings 1 metre or longer two installers are recommended.
    Rotating Bracket

Spaced 500mm, refer to luminaire cut sheet for allocated quantity per fitting.

STEP 2
Prepare mounting brackets and screws (Ø3mm with a minimum length of 12mm). Slide clip away from base so that you have clear access to screw holes.
Secure the base with screws on timber or metal surface ensuring that they are straight. Slide mounting clip back to the base when you are done.
Rotating Bracket

STEP 3
Ensure that all brackets are rotated the same way with the locking clips parallel with the base. Starting at one end push down the fitting until you hear that the clip lock into place. Continue along the profile until all clips are locked.
Once fitting is fully connected you can rotate the fitting to your desired angle.
Rotating Bracket

WIRING

If the fitting is wired from the back:
It will need to wired before mounting.
If the fitting is wired from the side:
It will need to wired after mounting.

Wire the fitting to the correct power supply as advised on the cut sheet.

  • Typically supplied with AU flex and plug (1.8m long)
    Wiring

archsales@coolon.com.au aus. 1300 287 533 intl. +613 8681 3633 www.coolon.com.au Version 1.2
All documentation is subject to change without notice. Refer to our website for the latest information

COOLON Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals