BEGA 50800.1 Wall luminaire for Indoors Velvet Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 50800.1 Wall luminaire for Indoors Velvet
Product Information
Product Usage Instructions
Instructions for use
Product description
Overvoltage protection
Cleaning · Maintenance
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50800.1 Wall luminaire for Indoors Velvet

Product Information

The product is a luminaire with LED lights. It has a power supply unit that operates on a voltage range of 220-240 V and a frequency range of 50-60 Hz. The luminaire is DALI-controllable, meaning it can be controlled using a DALI system. The product has basic insulation to ensure safety and protect temperature-sensitive components. It also features temporary thermal regulation to prevent damage to the luminaire. The installation and operation of the luminaire should comply with national safety regulations. Only a qualified electrician should perform the installation and commissioning. The manufacturer will not be liable for any damage caused by improper use or installation. Additional overvoltage protection components arerecommended for enhanced protection against transients. The product has a lamp module with a connected wattage of 23.6 W and a luminaire-connected wattage of 27 W. The rated temperature for the product is between 25°C and 40°C. The colour temperature of the LED lights is 3000 K, and the colour rendering index (CRI) is greater than 90. The module luminous flux is 3500 lm, and the luminaire luminous flux is 2802 lm. The luminaire has a luminous efficiency of 103.8 lm/W.

Product Usage Instructions

Ensure that the installation and operation of the luminaire comply with national safety regulations.
Only a qualified electrician should perform the installation and commissioning.
If modifications are made to the luminaire, the person responsible for these modifications will be considered the manufacturer.
Consider using separate overvoltage protection components for enhanced protection against transients.
Avoid touching the light output opening of the LED directly during installation or relamping.
Regularly clean the luminaire with solvent-free cleansers to remove dirt.
If necessary, replace the LED module using the provided spare parts: Synthetic cover, LED power supply unit, LED module 3000 K, and Reflector.

Instructions for use

Application
Wall luminaire · indoor luminaire for the glare free illumination of wall surfaces with the mounting surface being the reflection surface. The light emits upwards and downwards.

Product description

Luminaire housing made of aluminium, finish Colour velvet white
Synthetic cover with light diffusing structure Reflector made of pure anodised aluminium
2 elongated fixing holes
Width 5.5 mm · 570 mm spacing
1 cable entry for through-wiring
for mains cable
Connection terminal 2.5@
Earth conductor connection
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-264 V
DALI-controllable
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Impact strength IK04
Protection against mechanical
impacts < 0.5 joule
– Safety mark
– Conformity mark
Weight: 3.7 kg
This product contains light sources of energy efficiency class(es) D $BEGA-50800.1-Wall-luminaire-for-Indoors-Velvet-fig-$4$$

Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Lamp

Module connected wattage: 23.6 W
Luminaire connected wattage: 27 W
Rated temperature: ta = 25 °C
Ambient temperature: ta max = 40 °C

50 800.1 K3

Module designation: 4x LED-1050/930
Colour temperature: 3000 K
Colour rendering index: CRI > 90
Module luminous flux: 3500 lm
Luminaire luminous flux : 2802 lm
Luminaire luminous efficiency: 103,8 lm / W

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo the hexagon socket head screws (wrench size 3 mm) and lift luminaire top. Loosen earth connection (plug connection) and LED-connection between luminaire top and luminaire base.
Lead the mains supply cable through the cable entry of the luminaire base.
Note position of application “arrow down”. Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Make earth conductor connection.
Push silicone sleeves over the lines and make electrical connection.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light output.
Make earth connection (plug connection) and LED-connection between luminaire top and luminaire base again.
Note position of application of the luminaire “arrow down”.
Install luminaire top part, adjust it and tighten screws evenly.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Undo one of the two external locking screws (Torx) in the luminaire housing and remove the lateral housing cover.
Remove the synthetic cover from the profile of the luminaire housing.
Remove the LED module. Install the replacement LED module. Please follow the installation instructions for the LED module.
A defective synthetic cover must be replaced. Close up the luminaire again in reverse order.