RYOBI PBL350 18V 30 Degree Framing Nailer Owner’s Manual

RYOBI PBL350 18V 30 Degree Framing Nailer Owner’s Manual

Overview

A – Pusher
B – Mode selector
C – Belt clip screw mount
D – Grip switch
E – Trigger switch
F – Magazine release button
G – Bottom-loading magazine
H – LED
I – No-mar pad
J – Workpiece contact
K – Jam release
L- Depth of drive adjustment

WARNING:

To reduce the risk of injury, the user must read and understand the operator’s manual before using this product

SAVE THIS MANUAL FOR FUTURE REFERENCE

GENERAL POWER TOOL SAFETY WARNINGS

WARNING
Read all safety warnings, instructions, illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury

Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains operated (corded) power tool or battery-operated (cordless) power tool.

WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

• Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators.
  There is an increased risk of electric shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions.
  Water entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

• If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

• Use this product only with batteries and chargers listed in tool/appliance/battery pack/charger correlation supplement 987000-432.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
• Do not wear loose clothing or jewelry. Contain long hair. Loose clothes, jewelry, or long hair can be drawn into air vents.
• Do not use on a ladder or unstable support. Stable footing on a solid surface enables better control of the power tool in unexpected situations.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/ or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

BATTERY TOOL USE AND CARE

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
• Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 265° F may cause explosion.
• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
• SERVICE
• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
• Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
• When servicing a power tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance instructions may create a risk of shock or injury

NAILER SAFETY WARNINGS

• Always assume that the tool contains nails. Careless handling of the nailer can result in unexpected firing of nails and personal injury.

• Do not point the tool towards yourself or anyone nearby. Unexpected triggering will discharge the nail causing an injury.

• Do not actuate the tool unless the tool is placed firmly against the workpiece. If the tool is not in contact with the workpiece, the nail may be deflected away from your target.

• Disconnect the tool from the power source when the fastener jams in the tool. While removing a jammed fastener, the nailer may be accidentally activated if it is plugged in.

• Use caution while removing a jammed nail. The mechanism may be under compression and the nail may be forcefully discharged while attempting to free a jammed condition.

• Do not use this nailer for fastening electrical cables.
  It is not designed for electric cable installation and may damage the insulation of electric cables thereby causing electric shock or fire hazards.

• Hold power tool by insulated gripping surfaces, when performing an operation where the nail may contact hidden wiring. Nails contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

• Know your power tool. Read operator’s manual carefully. Learn its applications and limitations, as well as the specific potential hazards related to this power tool. Following this rule will reduce the risk of electric shock, fire, or serious injury.

• Always wear eye protection with side shields marked to comply with ANSI Z87.1. Everyday glasses have only impact resistant lenses. They are not safety glasses. Following this rule will reduce the risk of serious personal injury.

• Eye protection which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

• The employer and/or user must ensure that proper eye protection is worn. We recommend Wide Vision
  Safety Mask for use over eyeglasses or standard safety glasses that provide protection against flying particles both from the front and side. Always use eye protection which is marked to comply with ANSI Z87.1.

• Additional safety protection will be required in some environments. For example, the working area may include exposure to noise level which can lead to hearing damage. The employer and user must ensure that any necessary hearing protection is provided and used by the operator and others in the work area. Some environments will require the use of head protection equipment.
  When required, the employer and user must ensure that head protection conforming to ANSI Z89.1-1997 is used.

• Keep fingers away from trigger when not driving fasteners to avoid accidental firing.

• Use safety equipment. Always wear eye protection.
  Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

• Protect your lungs. Wear a face or dust mask if the operation is dusty. Following this rule will reduce the risk of serious personal injury.

• Protect your hearing. Wear hearing protection during extended periods of operation. Following this rule will reduce the risk of serious personal injury.

• Battery tools do not have to be plugged into an electrical outlet; therefore, they are always in operating condition. Be aware of possible hazards when not using your battery tool or when changing accessories. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

• Do not place battery tools or their batteries near fire or heat. This will reduce the risk of explosion and possibly injury.

• Use the tool only for its intended use. Do not discharge fasteners into open air.

• Use the tool only for the purpose for which it was designed.

• Use only the nails recommended for this tool. Use of the wrong nails could result in poor nail feeding, jammed nails, and nails leaving the tool at erratic angles. If nails are not feeding smoothly and properly, discontinue their use immediately. Jammed and improperly feeding nails could result in serious personal injury.

• Never use this tool in a manner that could cause a nail to be directed toward anything other than the workpiece.

• Do not use the tool as a hammer.

• Always carry the tool by the handle.

• Do not alter or modify this tool from the original design or function without approval from the manufacturer.

• Always be aware that misuse and improper handling of this tool can cause injury to yourself and others.

• Never clamp or tape the trigger or workpiece contact in an actuated position.

• Never leave tool unattended if the battery is installed.

• Do not operate this tool if it does not contain a legible warning label.

• Keep the tool and its handle dry, clean and free from oil and grease. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any strong solvents to clean your tool. Following this rule will reduce the risk of loss of control and deterioration of the enclosure plastic.

OPERATION

• Do not use tool if trigger does not actuate properly.
  Any tool that cannot be controlled with the trigger is dangerous and must be repaired.

• Check operation of the workpiece contact mechanism frequently. Do not use the tool if the workpiece contact mechanism is not working correctly as accidental driving of a nail may result. Do not interfere with the proper operation of the workpiece contact mechanism.

• Do not use a tool that does not work correctly.

• Always assume that the tool contains nails.

• Do not carry the tool from place to place holding the trigger. Accidental discharge could result.

• Always handle the tool with care:

  • Respect the tool as a working implement.
  • Never engage in horseplay.
  • Never pull the trigger unless nose is directed toward the work.
  • Keep others a safe distance from the tool while tool is in operation as accidental actuation may occur, possibly causing injury.

• Choice of triggering method is important. Check manual for triggering options.

• The tool is designed for single-hand use. Do not hold the tool by the front of the magazine. Do not put hands, head, or other parts of your body near the bottom of the magazine where the nail exits the tool, as serious personal injury could result.

• Do not point the tool toward yourself or anyone whether it contains nails or not.

• Do not actuate the tool unless you intend to drive a nail into the workpiece.

• Always ensure that the workpiece contact is fully positioned above the workpiece. Positioning the workpiece contact only partially above the workpiece could cause the nail to miss the workpiece completely and result in serious personal injury.

• Do not drive nails near edge of material. The workpiece may split causing the nail to ricochet, injuring you or a coworker. Be aware that the nail may follow the grain of the wood, causing it to protrude unexpectedly from the side of the work material or deflect, possibly causing injury.

• Keep hands and body parts clear of immediate work area. Hold workpiece with clamps when necessary to keep hands and body out of potential harm. Be sure the workpiece is properly secured before pressing the fastener against the material. The workpiece contact may cause the work material to shift unexpectedly.

• Keep face and body parts away from back of the tool cap when working in restricted areas. Sudden recoil can result in impact to the body, especially when nailing into hard or dense material.

• During normal use the tool will recoil immediately after driving a fastener. This is a normal function of the tool. Do not attempt to prevent the recoil by holding the nailer against the work. Restriction to the recoil can result in a second fastener being driven from the nailer.
  Grip the handle firmly, let the tool do the work and do not place second hand on top of tool or near exhaust at any time. Failure to heed this warning can result in serious personal injury.

• Do not drive fasteners on top of other fasteners or with the tool at an overly steep angle as this may cause deflection of fasteners which could cause injury.

LOADING TOOL

• Do not load the tool with fasteners when any one of the operating controls is activated.
• When loading tool:
• Never place a hand or any part of body in fastener discharge area of tool.
• Never point tool at anyone.
• Do not pull the trigger or depress the workpiece contact as accidental actuation may occur, possibly causing injury

SAVE THESE INSTRUCTIONS

• Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also.

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

result in death or serious injury.
| WARNING:| Indicates a hazardous situation, which, if not avoided, could result in death or serious injury.
| CAUTION:| Indicates a hazardous situation, that, if not avoided, may result in minor or moderate injury.
| NOTICE:| (Without Safety Alert Symbol) Indicates information considered important, but not related to a potential injury (e.g. messages relating to property damage).

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

understand operator’s manual before using this product.
| Eye Protection| Always wear eye protection with side shields marked to comply with ANSI Z87.1.
| Keep Hands Away| Keep hands and body away from the discharge area of the tool.
| Wet Conditions Alert| Do not expose to rain or use in damp locations.
| Recycle Symbol| This product uses lithium-ion (Li-ion) batteries. Local, state or federal laws may prohibit disposal of batteries in ordinary trash. Consult your local waste authority for information regarding avail- able recycling and/or disposal options.
V| Volts| Voltage
A| Amperes| Current
Hz| Hertz| Frequency (cycles per second)
min| Minutes| Time
| Direct Current| Type or a characteristic of current
| No Load Speed| Rotational speed, at no load
…/min| Per Minute| Revolutions, strokes, surface speed, orbits etc., per minute

GLOSSARY

Activate (operating controls)
To move an operating control so that it is in a position that allows the tool to be actuated or that satisifes one requirement for the tool to be actuated.

Actuate (tool)
To cause movement of the tool component(s) intended to drive a fastener.

Actuation system
The use of a trigger, workpiece contact, and/or other operating control, separately or in some combination or sequence, to actuate the tool.

• Single sequential actuation
  An actuation system in which there is more than one operating control and the operating controls must be activated in a specific sequence to actuate the tool. Additional actuation can occur when a specific operating control, other than a workpiece contact, is released and re-activated.

• Contact actuation
  An actuation system in which there is more than one operating control and the operating controls can be activated in any sequence to actuate the tool. Additional actuation can occur when any operating control is released and re- activated.

Fastener
A staple, pin, brad, nail, or other fastening device which is designed and manufactured for use in the tools within the scope of this standard.

Jam
An obstruction in the feed or drive areas of the tool.

Operating control
A control that separately, or as part of an actuation system, can cause the actuation of a tool.

Trigger
A tool operating control activated by a tool operator’s fingers.

Workpiece
The intended object into which a fastener is to be driven by a tool.

Workpiece contact
An operating control element or assembly on the tool intended to be activated by the material to be fastened.

FEATURES

PRODUCT SPECIFICATIONS

Motor………………………………………………………….18 Volt DC
Magazine Capacity……………………………………………60 nails
Minimum Nail Shank Diameter…………………………. 0.113 in.
Maximum Nail Shank Diameter………………………….0.131 in.
Fastener Range……………………………………..2 in. – 3-1/2 in.

ASSEMBLY

WARNING:
Do not use this product if it is not completely assembled or if any parts appear to be missing or damaged. Use of a product that is not properly and completely assembled or with damaged or missing parts could result in serious personal injury

WARNING:
Do not attempt to modify this product or create accessories or attachments not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

If any parts are damaged or missing, please call 1-800-525-2579 for assistance.

OPERATION

WARNING:
Do not allow familiarity with products to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury.

WARNING:
Always remove battery pack and nails from the tool before leaving the work area, moving the tool to another location, handing the tool to another person, assembling parts, cleaning, or when not in use. Always remove battery pack when making adjustments. Failure to do so could result in serious personal injury.

WARNING:
Always wear eye protection with side shields marked to comply with ANSI Z87.1. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury.

NOTICE:
If the tool is exposed to temperatures below 32ºF for long periods of time it may not operate. Allow the tool to warm up prior to use. If the tool is used in excessively high temperatures more than 104ºF for prolonged periods, the unit may not operate properly or it may shut down. Allow the tool to cool before resuming normal use.

APPLICATIONS

You may use this tool for the purposes listed below:

• Framing
• Floor Decking
• Exterior Decks
• Engineered Lumber
• Blocking Sub-Assemblies
• Fencing
• Crate and Box Assembly
• Trusses
• Pallets and Pallet Repair
• Subflooring

WARNING:
Always wear eye protection. Eye protection does not fit all operators in the same way. Make sure the eye protection chosen has side shields or provides protection from flying debris both from the front and sides.

ATTACHING THE BELT CLIP
See Figure 1, .

A – Belt clip
B – Screw
The belt clip can be installed on the side of the nailer.

• Align belt clip and screw with the screw hole.
• Using a Phillips head screwdriver (not included), tighten securely

INSTALLING/REMOVING BATTERY PACK

See Figure 2,.

A – Depress latches
B – Battery pack

NOTE: Use of a 3Ah or higher battery is recommended for the best performance.

• To install, place the battery pack in the tool. Align raised rib on battery pack with the groove inside the tool.
  NOTE: During battery installation the battery foot will move, this is an intentional design.

• Make sure the latches on both sides of the battery pack snap into place and the battery pack is secured in the tool before beginning operation.
  NOTE: Squeeze grip switch to activate nailer.

• To remove, locate latches on both sides of the battery pack and depress to release the battery pack from the tool.

For complete charging instructions, see the operator’s manuals for your battery pack and charger.

NO-MAR PAD

**See Figure 3,.

**

A – No-mar pad
B – No-mar pad storage

The no-mar pad attached to the nose of the tool helps prevent marring and denting when working with softer woods.

WARNING:
Remove the battery pack from the tool before removing or replacing the no-mar pad. Failure to do so could result in serious personal injury.

The pad can be removed by pulling it down and away from the nose. To replace the pad, fit it into place over the nose and push up at the back to reseat.

LOADING THE TOOL WITH NAILS
See Figures 4 and 5,.

A – Nail strip

A – Pusher

• Remove battery pack from the tool.
• With the nose of the tool pointed away from you, feed a strip of nails into the magazine. Be sure the nails are pointed downward and at the angle shown.

WARNING:
Keep the tool pointed away from yourself and others when loading nails. Failure to do so could result in possible serious personal injury

• Slide the pusher all the way to the rear of the magazine.
  Release the pusher and allow it to push the nails up to the driving mechanism. The pusher will stop when it rests against the end of the nail strip.

NOTE: Do not allow the pusher to snap back into place.

WARNING:
Use only the nails recommended for use with this tool.
The use of any other nails can result in tool malfunction, leading to serious injuries.

WARNING:
Never load nails with the workpiece contact or trigger activated. Doing so could result in possible serious personal injury.

WARNING:
Do not use nails with a shank smaller than 0.113 in. diameter. Doing so may cause nails to exit the tool prematurely through the guide track. Do not use hardened nails with this tool. This could lead to excessive wear of the guide body and allow nails to exit the back of the guide body, leading to serious personal injury.

DEPTH OF DRIVE ADJUSTMENT
See Figure 6,.

A – To increase depth
B – To decrease depth
C – Drive depth adjustment

The depth-of-drive of the nail may be adjusted. It is advisable to test the depth on a scrap workpiece to determine the required depth for the application.

To achieve the desired depth, use the depth-of-drive adjustment on the tool.

• Remove the battery pack and remove nails from the tool.
• Turn the depth selector left or right to change the driving depth.
• Install the battery and reload the tool with nails.
• Drive a test nail after each adjustment until the desired depth is set.

NOTE: Set depth of drive at the shallowest depth that will meet your needs.

DRIVING NAILS AT AN ANGLE
See Figure 7,.

DO NOT DRIVE NAILS

When driving nails at an angle, make sure that the tool is pointed away from yourself and others.
When driving nails at an angle, make sure that the tool is positioned correctly. Driving at an angle that is too steep may:

• cause the nail to miss the workpiece
• cause the nail to ricochet
• cause the workpiece to splinter, causing the nail to come back toward the operator.

WARNING:
Never drive a nail at an angle by tilting the tool forward.
This could lead to the fastener missing the work surface or bouncing off the work surface, leading to serious injury.

WARNING:
Remove the battery from the tool before removing nails or clearing a jammed fastener. Failure to do so could result in serious personal injury.

USING THE MODE SELECTOR SWITCH
See Figures 8 and 9,.

A – Mode selector switch
B – Single sequential actuation (T)
C – Contact actuation (TTT)

A – Trigger
B – Grip switch
C – Workpiece contact

WARNING:
Never wedge or hold back the workpiece contact mechanism during operation of the tool. Doing so could result in possible serious injury

This tool is shipped from the factory with the mode selector switch set in the Single Sequential Actuation mode. The mode selector switch can also be set for Contact Actuation mode.

SINGLE SEQUENTIAL ACTUATION MODE
Single sequential actuation provides the most accurate nail placement.

• Remove battery pack from the tool.

• Slide the selector to position (T).
  WARNING:
  The nailer will not function properly if the selector is not securely seated in either position (T) or (TTT). Always assure the selector is seated properly to avoid an unexpected nail discharge and possible serious personal injury

• Reinstall battery and activate the tool by pressing the grip switch.

• Grip the tool firmly to maintain control. Position the nose of the tool onto the work surface.

• Push the tool against the work surface to depress the workpiece contact.

• Squeeze the trigger to drive a nail.
  NOTE: Hold trigger until drive cycle is complete. If depressing the trigger does not drive a nail, release the trigger and lift the tool away from the workpiece, then replace and try driving the nail again.

• Always remove your finger from the trigger when the desired number of fasteners has been driven.

CONTACT ACTUATION MODE

Contact actuation allows very fast repetitive nail placement.

• Remove battery pack from the tool.

• Slide the selector to position (TTT).

• Reinstall battery and activate the tool by pressing the worklight grip switch.

• Grip the tool firmly to maintain control.

• Squeeze and hold the trigger. Push the tool against the work surface to depress the workpiece contact and drive a nail. To drive another nail, lift the tool and press the contact against the work surface again.
  NOTE: Hold trigger and keep workpiece contact depressed until drive cycle is complete.

• Always remove your finger from the trigger when the desired number of nails has been driven.

NOTE: In Contact Actuation Mode, the tool may also be operated by pressing the workpiece contact against the surface and squeezing the trigger.

WARNING:

During normal use the tool will recoil immediately after driving a nail. This is a normal function of the tool. Do not attempt to prevent the recoil by holding the nailer against the work. Restriction to the recoil can result in a second nail being driven from the nailer. Failure to heed this warning can result in serious personal injury.

DRY-FIRE LOCKOUT

When the magazine has 0-5 nails remaining, the dry-fire lockout feature will not allow continued operation.
To resume operation, reload the tool with nails.

REMOVING NAILS FROM THE TOOL
**See Figure 10 – 11,..

**

A – Magazine release button
B – Framing nails

A – Framing nails
B – Pusher
C – Nail stop tab

WARNING:
Remove the battery pack before removing nails or clearing a jammed nail. Failure to do so could result in serious personal injury.

• Remove the battery pack.

• To remove a strip of nails from the tool, press the release button on the pusher and guide it to the top of the magazine. When released, the nails will be released.
  NOTE: Always keep fingers clear of nail track of magazine to prevent injury from unintended release of the pusher.

• Press down on the nail stop tab near the end of the magazine and slide the nails over the tab.

• Remove the nail strip from the tool.

CLEARING A JAMMED FASTENER
See Figure 12 – 14,.

A – Magazine release mount
B – Jam-clearing mechanism

A – Needle nose pliers
B – Driver blade

A – Magazine
B – Magazine release screw
C – Driver blade
D – Jammed nail
E – Rear magazine release screw
F – LED

WARNING:
Remove the battery pack from the tool before clearing a jammed nail. Failure to do so could result in serious personal injury.

If a jam occurs, the tool will automatically enter into a jam mode and reset the driver blade. The tool LED, located underneath the mode switch, will flash red. Remove the battery pack. Check to ensure that the tool is free from a jammed fastener. In the event of a severe jam the magazine may require removal to clear the jammed fastener before reinserting the battery. The battery must be removed and reinstalled to reset it into normal operation mode.

• Remove battery pack from the tool.

• Remove fasteners from the tool.

• Using the included hex key, loosen, but do not remove, the two socket head cap screws at the front of the magazine that mount it to the tool.

• With the same hex key loosen the rear mounting socket head cap screw two to three turns, but do not remove it.

• Slide the magazine towards the rear of the tool. This should expose the jammed fastener and allow for easy clearing. If needed the magazine can be removed.

• Remove the bent nail, using needle-nose pliers if necessary.
  NOTE: If a jam is too severe and needle nose pliers can’t remove the jammed fastener, the tool may need to be serviced by an authorized service center.

• Reverse steps to replace the magazine.

MAINTENANCE

WARNING:
When servicing, use only identical replacement parts.
Use of any other parts could create a hazard or cause product damage.

GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

REQUIRED DAILY CHECKLIST

• Remove the battery pack from the tool and remove all fasteners.

• Check all screws, nuts, bolts, and pins on the tool. If any of these are loose, they must be tightened with the appropriate size wrench.

• Press the workpiece contact against a workpiece to ensure that it moves smoothly.

• With the workpiece contact depressed, pull the trigger.
  The trigger should move smoothly, without binding.

• Select the full sequential actuation mode ( ).

• While the tool is not loaded, insert the battery into the tool.

• Begin inspection:

  • Press the grip switch to activate the nailer.
  • Without pulling the trigger, press the workpiece contact against a workpiece several times. The tool must not actuate.
  • With the workpiece contact not engaged on the workpiece, point the tool down and away and pull the trigger several times. Hold the trigger in this position for a minimum of 5 seconds The tool must not actuate.
  • Load fasteners, then press the workpiece contact firmly against the workpiece and pull the trigger. The tool must actuate.
  • With the workpiece contact still depressed, release the trigger. The driver must return to its up position.

• Remove the battery pack and remove all fasteners.

• Select the contact actuation mode (TTT ).

• Place the battery pack in the tool.

• Begin inspection:

  • With the workpiece contact not engaged on the workpiece, point the tool down and away. Pull the trigger. The tool must not actuate.
  • Load fasteners, then fully depress the trigger and push the workpiece contact against a workpiece. The tool must actuate.

• Remove the battery pack and remove all fasteners.

• If the tool successfully meets all the requirements in this checklist, it is ready for use. Set the trigger on the tool to operate in the manner that best fits your application.

• Set the depth of drive according to the Depth-of-drive Adjustment section in this manual.

• Place the battery pack in the tool and load the proper fasteners for the desired application. Repeat this checklist before using the tool each day, or if the tool is dropped or damaged in any way.

REFILLING THE AIR PRESSURE TANK
See Figure 15,.

A – Plastic cover
B – Hex key
C – Air fill valve

After the intial use, you may notice a decrease in performance.
Refilling the air pressure tank to 125 psi can help restore the unit’s perfomance.

• Remove the battery pack and all nails from the tool.

• Remove the plastic cover from the bottom of the tool with the included hex wrench.

• Twist slightly and remove the plastic cap from the air fill valve.

• Connect an air compressor to the valve and pressurize the tank to a maximum of 125 psi. Allow the tool to recharge for approximately 30 seconds.
  NOTE: It is normal to hear a hissing sound while the tank is being refilled. Do not overfill. Always check the pressure before use. If overfilling occurs, a safety overflow valve will open to allow the excessive pressure to escape. Once the pressure has decreased, the valve will close automatically.
  WARNING:
  Never pressurize tank to more than 125 psi. Failure to heed this warning can result in serious personal injury.

• Disconnect the air compressor and replace the plastic cap and cover before use.

• Reattach the plastic cover to the bottom of the tool with the included hex wrench.

TROUBLESHOOTING

Remove battery and clear jam
Tool operates properly, but nails do not drive fully| Air pressure is too lowDepth of drive isn’t deep enough Nail is too long for wood hardnessTrigger released too soon Battery pairing is unsuitable| Refill air pressure tank Adjust depth of driveUse nail length that is appropriate for woodHold trigger until fastener is driven Use a 3Ah battery or higher
Tool operates properly, but nails are driven too deep| Depth of drive is too deep| Adjust depth of drive
Tool jams frequently| Incorrect nails Damaged nails Loose magazine Dirty magazine| Verify that nails are the correct size Replace nailsTighten screws Clean magazine
Tool stops and LED flashes rapidly| Battery is low or has no charge Trigger released too early| Recharge batteryRemove battery and reinstall.
Tool has charged battery and LED is slowly flashing or LED does not turn off after approximately ten seconds of non-use| Tool has malfunctioned| Take tool to nearest authorized repair center

LED LIGHT FUNCTIONS

prob- lem persists, contact an authorized service center for repair.
Jam Mode| Flashing Red Light| Clear Jam – See Clearing a Jammed Fastener in Operations.

To request service, purchase replacement parts, locate an Authorized Service Center or obtain Customer or Technical Support:
Visit www.ryobitools.com or call 1-800-525-2579

If any parts or accessories are damaged or missing, do not return this product to the store. Call 1-800-525-2579 for immediate service.

Please obtain your model and serial number from the product data plate.

This product is covered under a 3-year limited Warranty. Proof of purchase is required.

MODEL NUMBER* SERIAL NUMBER

Model number on product may have additional letters at the end. These letters designate manufacturing information and should be provided when calling for service.

RYOBI is a trademark of Ryobi Limited and is used pursuant to a license granted by Ryobi Limited.

TTI CONSUMER POWER TOOLS, INC.
P.O. Box 1288, Anderson, SC 29622
Phone 1-800-525-2579

USA, Phone 1-800-525-2579
USA, Phone 1-800-525-2579
www.ryobitools.com

References

• REIMAGINE WITH RYOBI - RYOBI Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>