J-TECH DIGITAL JTD-P6 6 Button Control Panel Wall Plate User Manual

: June 12, 2024
: J-TECH DIGITAL

J-TECH DIGITAL JTD-P6 6 Button Control Panel Wall Plate User Manual

SAFETY PRECAUTIONS

To ensure the best from the product, please read all instructions carefully before using the device. Save this manual for further reference.

Unpack the equipment carefully and save the original box and packing material for possible future shipment.
Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
Do not dismantle the housing or modify the module. It may result in electrical shock or burn.
Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or malfunction.
Refer all servicing to qualified service personnel.
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
Do not put any heavy items on the extension cable in case of extrusion.
Do not remove the housing of the device as opening or removing housing may expose you to dangerous voltage or other hazards.
Install the device in a place with fine ventilation to avoid damage caused by overheat.
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on to the housing, unplug the module immediately.
Do not twist or pull by force ends of the optical cable. It can cause malfunction.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
Unplug the power cord when left unused for a long period of time.
Information on disposal for scrapped devices: do not burn or mix with general household waste, please treat them as normal electrical wastes.

Introduction

Introduction to JTD-P6

The Wall plate Control Panel has (2) built-in programmable RS 232 connectors and (2) Infrared (IR) connectors.

The Programmable Control Panel can fully control the compatible switches, as well as third-party devices such as matrix switcher, compact scale switcher, projectors, screens, etc. Use the device for presentations in showrooms, classrooms, and boardrooms.

Features

Six customizable control buttons
One volume control knob
Support IR, RS 232 and TCP/IP control
Can be controlled and configured via GUI
Can be powered by Po

Package List

1 xJTD-P6 Control Panel Wall Plate
6 x Button caps
2 x 3-Pin Pluggable terminal block
1 x 2-Pin Pluggable terminal blocks
1 x 5-Pin Pluggable terminal block
1 x Button label
1 x User Manual

Panel Description

No.	Name	Description
1	Power LED	Illuminates green when power on.
2	Volume Knob	Black volume knob, high-quality knob with high damping feel

and stable structure, about 12-13mm in diameter
3| Button| (6) crystal and luminescent programmable buttons: Each button can be programed with the Control Panel Software.
Each label within a button can be easily changed. Simply select the label you need and change it as shown below:
Installation
4| Volume indicator| 5x blue indicator lights, light up in percentage according to the volume knob (1-19%, 20-39%, 40-59%, 60-79%, 80-100%) RJ45 conne
5| TCPAP| RJ45 connector. Connects with PC to run the GUI to customize button control.
6| RESET| Long-press this button 3 seconds until the power LED goes out to start to the restore factory defaults, and then the LED will light up while the resetting is successful.
7| IR Sensor| Receives and learns the IR code to build the IR database.
8| PWR(12V)| Connects with 12V DC power adaptor.
9| RELAY| Two groups of Relay Control, share a common switch interface, default ON
10| IR| Two sets of IR OUT, share a ground port, 5V standard, connect to the infrared emitting rod
11| RS232| 2 RS232 ports. Connect the third-party devices which are need to be controlled via the WP6P.

System Connection

The JTD-P6 can active different ports at one time. It means every button can send the RS232 commands, IR code at the same time. The demo system diagram as below:

System Diagram

Connect the STD-P6 to the LAN port of Wireless Route, or control device (such as PC) to TCP/IP port.
Connect the third-party devices (such as Matrix Switcher, Compact Scaler Switcher or Projector) that need to be controlled to RS232 (1) ~RS232 (3) ports.
Connect the IR Emitters to IR (1) ~ IR (2) ports.
Connect to the third-party devices that need to be controlled by relay.

GUI Control

Log In

The JTD-P6 is controlled by TCP/IP. The default settings are:

IP Address: 192.168.0.178
Subset Mask: 255.255.250.0

Username: admin
Password: admin
Log In

Type the username and password, and then click the login to enter the GUI setting.

Home

Click the volume icon to adjust the volume; or click the knob icon to implement the corresponding event;
Mouse operation click the corresponding butto

Configuration

Knob
Configuration

Knob/Button: Choose the knob or button to enter the event setting page
Start up: Click to enter the starts up event setting page
Set the Knob events: Turn Left, Press Down Setting or Turn Right

Button
Configuration

Click the Button 1 to set the button 1 event, click Add Event and then set the Event and the corresponding settings
One button can set multiple command events, such as TCP/IP, RS232, IR, RELAY, Delay and LED status

TCP/IP
Configuration

Set the TCP/IP event, such as IP, Port, Format, End Char for ASCI| and Data

RS232
Configuration

Set the RS 232 event, and then click save button to finish setting.

IR
Configuration

In IR event, user can import or export the IR command
Set the Event Name, Port, Code or Custom and IR Code for the event
Click Save button to finish setting

Relay
Configuration

Sect the Event Name, Port and the Action Mode
Click Save button to finish setting

LED
Configuration

Set the Event Name, Button Select, Status and LED Color
Click the Save button to finish setting

Delay
Configuration

Set the delay event to trigger the event after how long to press
Click Save button to finish setting

Network

Select dynamic or static IP mode. Under static mode, then IP Address, Subnet Mask and Gateway can be reset.

Setting

Credentials: setting the username and new password and then click confirm button to perform the modification.
Update Profile: Import or export the setting file to implement the system configuration.
Factory Default: Click Factory reset

Upgrade

Firmware Upgrade: click the browse to choose the upgrade file (the file needs to be renamed as “WP6P.app”) and then click upgrade to execute upgrade.

Specifications

Program Port	TCP/IP
Output Port	2xRS232, 2 x IR, 2 x Relay
Output Connector	2 x 3-pin pluggable terminal blocks 2 x 2-pin pluggable

Panel Drawing

Maintenance

Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner, or benzine to clean.

Warranty

If your product does not work properly because of a defect in materials of workmanship, our company (referred to as “the warrantor”) will, for the length of the period indicated as below, “Parts and Labor (18) Months”, which starts with the date of original purchase (“Limited Warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b) replace it with a new or a refurbished product. The decision to repair or replace will be made by the warrantor.

During the “Labor” limited warranty period, there will be no charge for labor. During the “Parts” warranty period, there will be no charge for parts. You must mail-in your product during the warranty period. This Limited Warranty is extended only to the original purchaser and only covers products purchased as new. A purchase receipt or other proof of original purchase date is required for Limited Warranty service.

Mail-In Service

When shipping the unit, carefully pack and send it prepaid, adequately insured, and preferably in the original carton. Include a letter detailing the complaint and provide a day time phone and/or email address where you can be reached.

Limited Warranty Limits and Exclusions

This Limited Warranty ONLY COVERS failures due to defects in material or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The Limited Warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, mis- adjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, or service by anyone other than a Factory Service center or other Authorized Servicer, or damage that is attributed to acts of God.

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTAIL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having someone remove or re-install an installed unit if applicable, travel to and from the service, loss of or damage to media or images, data or other recorded content. The items listed are not exclusive, but are for illustration only.) PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR RESPONSIBILITY.

WWW._JTECHDIGITAL.COM
PUBLISHED BY J-TECH DIGITAL INC.
9807 EMILY LANE
STAFFORD, TX 77477
TEL: 1-888-610-2818
E-MAIL: SUPPORT@JTECHDIGITAL.COM

J-TECH DIGITAL INC.
9807 EMILY LANE
STAFFORD, TX 77477
TEL: 4 1-888-610-2818
E-MAIL: SUPPORT@JTECHDIGITAL.COM

J-TECH DIGITAL Logo