BEGA 51216.4 LED Wall Luminaire For Indoor Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
BEGA 51216.4 LED Wall Luminaire For Indoor Instruction Manual
Instructions for use
Application
Wall luminaire · Indoor luminaire with velvet white metal housing. Luminaire
with light source shielded to the front and metallic inside colour of the
reflection surface. Radial light emission 360°.
Product description
- Wall luminaire “STUDIO LINE”
- Luminaire housing made of aluminium, surface Colour velvet white inside hue matt brass
- Inside synthetic cover, translucent white 3 fixing holes ø 4.5mm
- Angle 120° · Pitch circle ø 155mm 1 cable entry for through-wiring for mains cable
- Connection terminal 2.5@
- Earth conductor connection
- LED power supply unit 220-240 V x 0/50-60 Hz
- DC 170-280 V
- BEGA Thermal Switch®
- Temporary thermal shutdown to protect temperature-sensitive components
- Safety class I
- Conformity mark
- Weight: 3.1 kg
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician. The manufacturer accepts no liability for damage
caused by improper use or installation. If subsequent modifications are made
to the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve an additional
protection against e.g. transients, etc. we recommend separate overvoltage
protection components. You can find them on our website at
www.bega.com.
Lamp
Module connected wattage: 25 W
Luminaire connected wattage: 28.4 W
Rated temperature : ta=25 °C
Ambient temperature : ta max=30 °C
51 216.4K3
Module designation : LED-1166/930
Colour temperature: 3000 K
Colour rendering index : CRI > 90
Module luminous flux: 3900 lm
Luminaire luminous flux: 712 lm
Luminaire luminous efficiency: 25,1 lm/W
Installation
LED are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping. Remove
the mounting plate with LED unit from its packaging.
Please note: A round blank made of synthetic material covers the mains
connection compartment. For the mains supply connection, this synthetic round
blank must be removed and refitted after the mains supply connection. Loosen
the black knurled screw (slotted) and remove the round made of synthetic
material from the LED unit. Pass the power connecting cable through the cable
entry in the mounting plate.
Fasten the mounting plate with the supplied fastening material or other
suitable fastening material to the installation surface. Establish the earth
conductor connection on the earthing screw (1) of the mounting plate. Make the
electrical connection to the terminals. Observe the correct configuration of
the connecting cable. Connect the live conductor to the brown wire (L) and the
neutral conductor to the blue wire (N). Insert the round made of synthetic
material back into the LED unit and tighten the black knurled screw
(slotted). Remove the luminaire housing (reflector) from its packaging and
carefully guide over the LED unit.
Place the luminaire housing (reflector) over the keyholes onto two threaded bolts of the LED unit and turn it clockwise until it stops. Tighten the two hex nuts M4 over the keyholes. Remove the supplied radial synthetic cover with round housing cover from the packaging, guide onto the centre of the grub screw of the LED unit and hand-tighten in the clockwise direction.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module ·
Replacing the power supply unit
The designation of the LED module is noted on a label in the luminaire. The
light colour and light output of BEGA replacement modules correspond to those
of the modules originally fitted. The replacement can be carried out by a
qualified person using standard tools. Disconnect the system from the power
supply. Loosen the radial synthetic cover with round housing cover by turning
it anti-clockwise from the LED unit. Loosen the black knurled screw (slotted)
and remove the round made of synthetic material from the LED unit. Disconnect
the earth conductor connection and the electrical connection to the terminal.
Loosen the mounting screws of the power supply unit, the round blank bracket
and earthing screws (Torx). Remove the pot with LED module. Install the
replacement pot. Please follow the installation instructions for the LED
module. Replace defective LED power supply unit. Tighten the mounting screws
of the power supply unit, the round blank bracket and earthing screws (Torx)
again. Establish the earth conductor connection on the earthing screw (1) of
the mounting plate. Make the electrical connection to the terminals. Observe
the correct configuration of the connecting cable. Connect the live conductor
to the brown wire (L) and the neutral conductor to the blue wire (N). Insert
the round made of synthetic material back into the LED unit and tighten the
black knurled screw (slotted). Guide the radial synthetic cover with round
housing cover onto the centre of the grub screw of the LED unit and hand-
tighten in the clockwise direction
Spares
LED power supply uni t: DEV-0422/700
LED module 3000 K : LED-1166/930
Reflector: 71 003 561 B14
Component round blank : 75 005 266
BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>