OFFICEJOY B08Q8BYM6Z 28.5 Inch Flat LED Electric Fireplace User Manual

USER’S MANUAL
28.5” Flat LED Electric Fireplace

B08Q8BYM6Z 28.5 Inch Flat LED Electric Fireplace

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Before You Start

Please read all instructions carefully.
Retain instructions for future reference.
Separate and count all parts and hardware.
Read through each step carefully and follow the proper order.
We recommend that, where possible, all items are assembled near to the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled.
Always place the product on a flat, steady and stable surface.
Keep all small parts and packaging materials for this product away from babies and children as they potentially pose a serious choking hazard.

CONSUMER SAFETY INFORMATION

• Read this manual before installing and operating this appliance
• Failure to follow these instructions may result in electric shock, fire property, or personal injury
• Do not store or use gasoline or other flammable liquids in vicinity of this appliance.

IMPORTANT SAFETY INFORMATION!

WARNING

• ALWAYS keep electric cords, home furnishings, drapes. clothing. papers, or other combustibles at least 3 feet (0.9m) away from the front of this heater, and away from the bottom, sides, and rear of this heater.
• DO NOT place the heater near a bed because objects such as pillows or blankets can fall off the bed and be ignited by the heater.
• DO NOT COVER this heater or block the air vents at all. Doing so could cause a fire.
• AVOID fire or electric shock! NEVER insert or allow any foreign objects ta enter the ventilation or exhaust openings of this heater.
• Prevent Fire! Keep all flammable liquids. like gasoline or paint, away from this heater. This heater produces arcing sparks that could ignite flammable liquids.
• DO NOT cover this heater in any manner. Doing so could block the air flow and cause the unit to overheat, or could ignite the material covering the heater.
• NEVER run the power cord under carpet, rugs, runners, or any other covering. Doing so could cause the cord or matenals covering the cord to overheat.
• AVOID FIRE! Regularty inspect all air vents to make sure they are free from dust, lint, or other blockage. Unplug the unit and clean with a vacuum ONLY. DO NOT nse or get wet.

WARNING

• For residential use only! NOT for commercial use! NEVER use this fireplace for other than its intended purpose.

• Only use this insert with the mantel that came with the insert. NEVER use a mantel from another manufacturer.

• NEVER use this electric fireplace insert unless it is properly installed in the correct mantel.

• Use extreme caution if using this heater near children, or where children may be present.

• NEVER leave this heater unattended. ALWAYS unplug this heater when not in use.

• This heater is hot when in use. AVOID INJURY! DO NOT TOUCH hot surfaces, or attempt to move this heater while it is hot.

• ALWAYS tum this heater off before unplugging it from the outlet.

• AVOID INJURY! Keep the cord from crossing traffic areas to avoid tapping.

• NEVER modify this fireplace. Doing so could result in personal injury or property damage.
  Modification of this fireplace completely voids all warranties.

• Discontinue use ff this fireplace malfunctions or is dropped or damaged in any manner.

WARNING

• Risk of electric shock! DO NOT OPEN! No user-serviceabie parts inside!

• ALWAYS disconnect this unit from the power supply before performing any assembly or cleaning, or before relocating the electric fireplace.

• ALWAYS store this heater in a dry locabon. NEVER use the fireplace if it has become wet.

• NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater could fall into a bathtub or pool, become damp or come in contact with water.

• NEVER hang this unit on a wall directly below an electrical outlet.

• NEVER operate this heater if the power cord or plug has becoma damaged, or if the grounding pin is damaged or missing.

• Place the heater near a wall outlet so an extension cord is not needed. If an extension cord is needed. the gauge of the cord must be at least 14AWG, and the rating must be at least 1875 Watts. NEVER use a smaller gauge cord with a lower rating. Doing so may result in fire or electric shock.

• ONLY use this heater on a 110~120 Volt 15 Amp grounded circuit. NEVER overload the circuit. If this heater tnps the circuit breaker, unplug all other appliances on the same circuit before the next use. Avoid plugging other appliances into the same circuit as this heater.

• NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or connections. Plugging this heater into a faulty outlet could result in electric arcing within the outlet that could cause the outlet to overheat or catch fire.

• ALWAYS check your heater cord and plug connections with each use!
  i) MAKE SURE the plug fits bght in the outlet! Faulty wall outlet connections or loose plugs can cause the outlet to overheat.
  ii) Heaters draw more current than small appliances. Overheating may occur even if it has not occurred with the use of other appliances.
  iii) During use check frequently to see if the plug outiet or faceplate is HOT!
  iv) If the outlet or faceplate is HOT, discontinue use immediately and have a qualified electrician inspect and/or replace the faulty outlets.

• The cord supplied with the heater has a plug with two blades (live and neutral) and one round pin (ground). if a 3-slot receptacle is not available, an adapter MUST be used. The adapter MUST be properly grounded to the outlet box (see figure at right).

PREPARATION

**** This insert has front panel made of GLASS! ALWAYS use extreme caution when handling glass. Failure to do so could result in personal injury or property damage.
Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Check the parts list to make sure nothing is missing. Dispose of packaging materials properly. Please recycle whenever possible.

Tools required for assembly: Phillips screwdriver (Not included)

PARTS & HARDWARE

Trim Kit

1. Four bracket are on either side of fireplace side.
2. Slide the trim kit onto the bracket. The flanges will fit the bracket.
3. Gently push the trim kit down until fully seated.

REMOTE CONTROL

The remote control operates with one 3V CR2025 Lithium Cell Battery (included). Remove the protective sheet between the battery and the contacts in order to operate (see Page 7).

ALWAYS unplug this fireplace heater before assembly or cleaning, or before relocating. Failure to do so could result in electric shock, fire. or personal injury.

Remote Control Set-up

• Fig. 1: Remove the plastic sheet from the end of the remote control to allow the battery to touch the electrical contacts. If the sheet is not removed, the remote control will not work.
• Fig. 2: To install or replace the battery, press the button to allow the battery case to slide out. Position the battery according the drawing. and slide the case back in to the remote.

NEVER dispose of batteries in fire. Failure to observe this precaution may result in an explosion. Dispose of batteries at your local hazardous material processing center.
ALWAYS replace the battery in the remote control with the same type of battery.
Failure to do so may result in personal injury or property damage.

OPERATION

Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in electric shock, fire, serious injury, or death.

Power
Make sure the ON/OFF switch, located on the control panel, is in the OFF position. Plug the power cord into a 110~120 Volt 15 Amp grounded outlet (see IMPORTANT SAFETY INFORMATION on Pages 3 and 4). Make sure the outlet is in good condition and  that the plug is not loose. NEVER exceed the maximum amperage for the circuit. DO NOT plug other appliances into the same circuit.

Thermostat
This heater is equipped with a Thermostat. Should the ambient temperature exceed/lower than the set temperature, the heater will automatically turn OFF/ON.

Methods of Operation
CONTROL PANEL: Controls ON/OFF, DIMMER, and HEATER.
REMOTE CONTROL: Controls ON/OFF, HEATER, and DIMMER.

Control Panel and Master Power Switch Locations

Control Panel

panel & remote control.
2. Press again to turn off flame effect, and shut off power to remote control and all functions.| 1. Flame effect and fuel bed turn on. Indicator light turns on. Control par el & remote control are enabled.
2. Flame effect and indicator light turn oft The control panel and remote control will not function.
| The Flame color controls the color of the flame effect.
Press the button to set the flame Color to the desired option.| The flame effect cycles through three kinds of color. Orange, bule, O&B mix.
Keep press this button for 3 seconds, 1 can adjust the flame brightness
| Flame effect must be ON for heater to function.
1. Press once for low neat (750W).
2. Press again for high heat (1500W).
3. Press again to turn off heater.| 1. Healer & fan turn on low (750W). Indicator light turns on. Warm air blows.
2. Heater & fan turn on high (1500W). Indicator light turns on. Hot air blows.
3. Heater turns off. Fans may blow air after heater is turned off to cool down.
| TEMPERATIRE button: Contra temperature settings to choose temperature as desired.
Setting range from 62F to 82F.| 1. Press once. Irtiotor light turn on. 1 cmpemturc it set so 62F.
Press again until desired setting is reached. LED display show setting.
| TIMER button: Control timer settings to turn off fireplace at selected time.
Settings range from 0 hours to 8 hours.| 1. Press once. Indicator light trun on. Temperature is set to hours.
Press again until desired setting is reached. LED display show setting.

Remote Control Operation

NOTE: Master Power switch on control panel must be ON to use remote control.

control functions.
2. Press again to turn off flame effect and shut off power to remote
coltrol and all functions.| 1. Flame effect and fuel bed turn on .
Indicator light turns on. Remote control functions are enabled.
2. Flame effect and indicator light turn off.
The remote control functions will not function..
| The DIMMER controls the brightness of the flame effect.
Press the button to set the flame effect to the desired level.| The flame effect cycles through different levels, then returns to the first level.
| Flame effect must be ON for heater to function.
1. Press crce for low heat (750W)
2. Press again for high heat (1500W).
3. Press again to turn oil Dealer.| 1. Heater & fan turn on low (750W).
Indicator light turns on. Warm air blows.
2. Healer & fan turn on high (1500W).
Indicator light turns on. Hot air blows.
3. Heater turns off Fans may blow air after heater is turned off to cool down.
| TEMPERATURE button: Control temperature settnnts to choose lonipeniture as desired.
Setting raoge from 62F to 82F.| 2. Press once. Indicator light turn on. Temperature is set to 62F.
Press again until desired setting is reached. LED display show setting.
| TIMER button. Control timer settings to turn off fireplace at seleeted time.
Setting range from 0 hours 8 hours.| 1. Press once. Indicator light turm on. Temperature is set to hours.
Press again until desired Setting is reached is reached. LED display Show Setting.
| COLON button. Makes the color flame effect charging.| 1. Press once. Flame coloer effect gets Charging.
Press aging until desired setting is reached.

NOTICE
To improve operation, DO NOT press the buttons too quickly. Give the unit time to respond to each command.
WARNING!
NEVER leave heater unattended during operation! Failura to do so Could result in personal injury or property damage.

NOTICE
When the heater is first turned on, a slight odor may be present This is normal and should not occur again unless the heater is not used for a long period of time.

FCC STATEMENT

Remote Control FCC Information

NOTE: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. the user is encouraged to try to correct the interference by one or more of the following measures:

• Reonent or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment. This Class B digital apparatus complies with Canadian ICES-003.

CARE AND MAINTENANCE

ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning. performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury.

Cleaning
NEVER immerse in water or spray with water. Doing so could result in electric shock, fire, or personal injury.
Metal:

• Buff using a soft cloth, slightly dampened with a citrus oil-based product.
• DO NOT use brass polish or household cleaners as these products will damage the metal trim.

Glass:
Use a good quality glass cleaner and dry thoroughly with a paper towel or lint-free cloth.
NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.

Venta:

• Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
• Clean the exterior of the fireplace with a slightly damp cloth or duster.

Maintenance

Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning. performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury.

Electrical and Moving Parts:

• The fan motors are lubncated at the factory and will not require lubrication.
• Electrical components are integrated in the fireplace and are not serviceable by the consumer.

Storage:
Store heater in a clean dry place when not in use.
WARNING! No other servicing should be performed by the consumer. Do not attempt to service the unit yourself.

TROUBLESHOOTING

WARNING: Turn off the appliance. unplug and let cool for at least 10 minutes before attempting to service. Only a qualified professional should attempt to service or repair the appliance.

2. LED bulb are burned out.
3. “Flame wand” has come loose from bracket.
4. “Flame wand” motor is not functioning.| 1. Push Dimmer button to increase Itght
2. Contact with the technical
3. Remove back panel. Secure end of ” flame wand” hack into the support
Bracket
4. Call of Technical gervice.
The appliance turns off and will not turn hack an| 1. The overheat protection device in the appliance has been triggered.
2. House circuit breaker has been tripped| 1. Trum all controls off. unplug the appliance, allow to cool kir at least 10 minutes, then plug hack in and restart.
2. Reset house circuit breaker.
The appliance does not turn on when the dutton is pushed to “ON”| 1. The overheat protection device in the appliance has been triggered.| 1. Turn all controls off, unplug the appliance. Allow to cool for at least 10 minutes, then plug back in and restart.
Remote control does not worts| 1. Low hatterics.
2. Manual control on the appliance must be “ON” before operating the remote control.| 1. Replace all batteries in the remote control
2. Push the appliance “ON” using the manual control panel, then use remote control to operate. If using the remote  control the appliance, you must also turn on the appliance “ON” using the remote control

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>