MOUNTUP MU0014 TV Wall Mount Full Motion Tilting Instruction Manual
- May 15, 2024
- MOUNTUP
Table of Contents
MOUNTUP MU0014 TV Wall Mount Full Motion Tilting
Safety Caution
Please read this instruction carefully before installation.
If you do not understand these instructions or have doubts about the safety of
the installation, assembly or use of this product, please contact us.
This product is designed for use in wood stud or solid concrete wall.
- DO NOT install into drywall alone.
The wall must be capable of supporting five times the weight of the TV and mount combined.
Incorrect installation may result in product damage or body injury.
WARNING: This product contains small items that could be a choking hazard
if swallowed.
Before starting assembly, verify all parts are included and undamaged. For
parts shortage or damage, please contact us.
Must Check Before Getting Started
Drywall with wood studs
Solid concrete wall
CAUTION: DO NOT install into drywall alone.
Installation Tools (Not Included)
Wood Stud Installation
Stud Finder
Awl
Wood Drill Bit
Concrete Installation
Masonry Drill Bit
Hammer
Band Tape
Pencil
Electro drill
Socket Wrench
Screwdriver
Hardware Included
Wall Plate
TV Plate
Extenders
Parts
x8 4A
x8 **4B
**
Allen key x1 **4C
**
Hardware （Wall /Product)
Lag Bolts 5/16 x 2½ in
Open-end wrench
TV Screws / Washers
Philips Screws
M4 x 12mm
M4 x 30mm
Philips Screws
M6 x 15mm
M6 x 30mm
Philips Screws
M8 x 25mm
M8 x 45mm
Spacers
L10mm
Washers
Ø6mm
M4-5-6
Spacers
L5mm
INSTALLATION INSTRUCTION
Parts
Velcro Cable Ties ×5
Bubble Level ×1
Feature
Max:400x400mm/16×16″
Min:100x100mm /4×4″
If you have any questions, please feel free to contact us via Amazon.
Warm Tips
You could also refer to the Video Guide about installation on our product
page.
Step 1-1 Select TV screw diameter
Thread screws by hand into the threaded holes on the back of your TV to select
which screw diameter fits your TV.
M4
M6
M8
Step 1-2 Select TV screw length
When attaching brackets to the flat screen, be careful not to over tighten
screws and be sure that screws do not bottom out in the mounting holes.
Step 2 Mesure your TV pattern
Measure and note the width and the height of the square or rectangle formed from the VESA holes pattern .
100mm ≈ 4in.
130mm≈ 5 1/8in.
200mm ≈ 8in.
300mm ≈ 11 3/4in
340mm ≈ 13 3/4in.
400mm≈ 16in.
Step 3-1 Select monitor plate configuration Step 3-2 Assemble TV plate and extenders
Select the configuration A , B , C, D, or E to use based on the measurement from STEP 2.
| VESA Pattern (WxH) | Configuration | VESA Pattern (WxH) | Configuration |
|---|---|---|---|
| 100mm x 100mm | A | 300mm x 200mm | C |
| 130mm x 130mm | A | 300mm x 300mm | E |
| 200mm x 100mm | A | 400mm x 200mm | C |
| 200mm x 200mm | A | 400mm x 300mm | D |
| 200mm x 300mm | B | 400mm x 400mm | E |
| 200mm x 400mm | B |
A: for VESA hole pattern: 100x100mm, 130x130mm,200x100mm, 200x200mm.
B: For VESA: 200x300mm, 200x400mm
C: For VESA: 400x200mm, 300x200mm
D: For VESA: 400x300mm
E: For VESA: 300x300mm, 400x400mm
Step 3-2 Assemble TV plate and extenders
If your TV hole pattern is greater than 200x200mm, attach extenders [3A ]
and [ 3B ] to TV plate [ 02 ] using Nut [ 4A ] and Bolt [ 4B
].
Step 3-3 Attach the brackets
( a ) For Flat Back
( b ) For Round Back / Extra Space
Step 4A Wall plate installation (wood stud)
Locate your studs. Verify and mark the center of the stud by finding the stud
edges using an awl, a thin nail, or an edge-to-edge stud finder.
Position the wall plate ( 01) at your desired height and line up the holes
with your stud center line. Level the wall plate and mark the pilot hole
locations.
IMPORTANT: of 2 3/4 in (70 mm). Be sure to drill into the center of the
stud.
Install wall plate ( 01 ) using lag bolts ( A ) with Socket Wrench,
NO Electrodrill. Tighten the lag bolts ( A ) until they are pulled
firmly against the wall plate 01 .
Step 4B Wall plate installation (concrete or brick)
Position the wall plate at ( 01 ) your desired height, level the wall
plate and mark the pilot hole locations x3.
Drill pilot holes
Install wall plate ( 01) using lag bolts ( A) with Socket Wrench, NO
Electrodrill. Tighten the lag bolts (A) until they are pulled firmly
against the wall plate 01 .
Step 5 Lift and hang TV with brackets onto wall bracket
Lift and hang TV assembly onto arm and wall plate.
Remove 2 preassemble screws and washers, save them for using to next step.
Secure the TV plate to the arm and wall plate with the removed screws and
washers from the previous step.
Adjustments
Tilting Adjustment
(Tilting)
Tilting Angle Adjustment (+5° / -15°) Loosen 2 tilting bolts, pull TV to
your desired angle, then fasten tilting nuts with Allen key.
Leveling adjustment (-3°/+3°)
If needed, TV can be leveled ±3 degrees via adjusting the 2 screws with the
open-end wrench.
Product dimensions:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>