BEGA 50350.6 LED Wall Luminaire Instruction Manual

: June 13, 2024
: BEGA

Table of Contents

BEGA 50350.6 LED Wall Luminaire
Product Information
Product Usage Instructions
Dimension
Instructions for use
Safety
Replacing the LED module
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50350.6 LED Wall Luminaire

Product Information

Product: Wall luminaire STUDIO LINE Product Description: Wall luminaire with a housing made of aluminum and a velvet white surface color
Features:

LED-Module for mains voltage 220-230 V, 50/60 Hz
Temporary thermal shutdown to protect temperature-sensitive components
Light sources energy efficiency class(es): F
Electronic components protected against overvoltage

Product Usage Instructions

The installation and operation of this luminaire should comply with national safety regulations.
Installation and commissioning should only be carried out by a qualified electrician.
The manufacturer does not accept liability for damage caused by improper use or installation.
If modifications are made to the luminaire, the person responsible for these modifications is considered the manufacturer.
To achieve additional protection against transients and overvoltage, separate overvoltage protection components are recommended

Dimension

BEGA-50350.6-LED-Wall-Luminaire-FIG-1

Instructions for use

Application
Wall luminaire · indoor luminaire with velvet white luminaire housing and inside hue. The light emits upwards and downwards.
Product description
Wall luminaire “STUDIO LINE” Luminaire housing made of aluminium, surface Colour velvet white inside hue matt copper Reflector made of pure anodised aluminium 2 elongated fixing holes Width 4.5 mm · 90 x 38 mm spacing 1 cable entry for through-wiring for mains cable Connecting terminal 2.5@ with plug connection Earth conductor connection LED-Module for mains voltage 220-230 V y 50/60 Hz BEGA Thermal Switch® Temporary thermal shutdown to protect temperature-sensitive components Safety class I r – Safety mark c – Conformity mark Weight: 0.8 kgThis product contains light sources of energy efficiency class(es) F

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation.If subsequent modifications are made tothe luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.To achieve an additional protection against e. g. transients, etc. we recommend separateovervoltage protection components. You can find them on our website at www.bega.com.

Lamp

Luminaire connected wattage 14 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 35 °C

50 350.6 K3

Module designation LED-0608/930
Colour temperature 3000 K
Colour rendering index Ra > 90
Module luminous flux 1320 lm
Luminaire luminous flux 214 lm
Luminaire luminous efficiency 15,3 lm / W

Installation
LED are high-quality electronic components! Please avoid touching the light output openingof the LED directly during installation or relamping. Undo set screw and lift off luminaire housing. Loosen LED connection and earth connection (plug connection). Pass the power connecting cable through the cable entry in the mounting plate. Note position of application of the luminaire “arrow down”. Fasten the mounting plate with the supplied fastening material or other suitable fastening material to the installation surface. Make earth conductor connection.Push silicone sleeves over the lines and make an electrical connection to terminal (plug connection). Make earth conductor connection between luminaire housing and mounting plate. Push LED plug into the coupler as fa as it will go. Install luminaire housing over the mounting plate and tighten set screw.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire. The light colour and light output of BEGA replacement modules correspond to thoseof the modules originally fitted. The module can be replaced by a qualified person using commercially available tools. Disconnect the system and open the luminaire. Please follow the installation instructions for theLED module. Close the luminaire.

Spares