GLOBAL INDUSTRIAL 812546 Dual Docking Station User Manual

GLOBAL INDUSTRIAL 812546 Dual Docking Station

User’s Manual

For any questions or assistance, please contact Customer Service:

US: 1-800-645-2986

Canada: 888-645-2986

Product Information

Application and Function Instruction

The docking station is composed of a sheet-metal base, battery plastic base, inverter, equalization disk, and LCD screen.

Front of Docking Station:

• Battery A
• Battery Display Screen

Rear of Docking Station:

• Battery B Power Switch
• Battery B Display Screen
• American Standard Three-pin Socket

Operation and Usage

1. Inspect the product for any visible damage to the appearance, loose or damaged output socket or battery pins. If any abnormal conditions occur, stop using the product.

2. Ensure that the power of the loaded device is within the specified range. Plug the device into the AC socket on the back of the product.

3. Plug the battery into the plastic battery compartment in the product.

4. Turn on the power switch. The device will start and the internal inverter will work. The load should function normally.
   When the screen works normally, it indicates that the corresponding battery is working.

5. If the product alarms a low-battery prompt, turn it off immediately and replace the battery with a new one.

Product Maintenance

1. Regularly inspect the socket contacts in the battery compartment. Replace any deformed or cracked contacts to prevent charging failure.
2. Regularly remove dust and dirt from the heat dissipation window.
3. Regularly check whether the external screws and lifting rings of the chassis are fully tightened.

Read this manual thoroughly prior to installation, operation or maintenance. Keep these instructions in a safe location for future reference. For questions, visit globalindustrial.com or contact Customer Service at 1-800-645-800-645-2982.

WARNING

• Failure to follow installation instructions will void warranty.
• When plugging in or pulling out the battery, please be cautious about the operation to avoid pins damage;
• The product should be kept away from fire, high-temperature environments, and humid and rainy environments during use and storage, otherwise it may lead to dangerous situations.
• Non-professionals should not disassemble it by themselves.
• Do not discard the product at the end of its service life. Recycle the product according to local laws and regulations.
• This product should be protected from rain, water immersion, moisture, and violent vibration during transportation.
• It cannot be used at an altitude exceeding 2000m.
• Do not drop, squeeze, or collide with the product, so as not to subject the product to external pressure, which may cause a short circuit of the internal circuit of the product and damage to the battery.
• After use, please turn off the machine in time.
• Please charge by the supplied power cord.
• When the product accidentally drops into the water while using, please unplug the input socket and place it in a safe and open area. The product shall not be turned on.
• While using or delivering the product, its screen should be carefully protected from strike.
• When the product is on, it is forbidden to touch pins in the battery compartment with hands or metal devices.

Dual Docking Station 812546

Technical parameters

1-minute interval and the screen will flash along with the alarm; When the battery level is ≤ 6%, the buzzer rings constantly. When the battery level is＜ 5%, the output will cut off. When the output load is≥ 500WZ,thescreenwillpopuptheoverload icon.
Product Size| 18.89 x 10.55 x 10.47 inch（LWH）
Product N.W.| 13.33 lbs
Product G.W.| 16.82 lbs
Working Environment| 14-104°F

Relative Humidity≤80% Altitude≤2000M

Transport and Storage Environment| Temperature: 5-131°F

Relative Humidity≤93%（no condensation） Atmosphere Pressure:70kPa～106kPa

Package Contents:

• Dual Docking Station * 1
• Product Instruction Manual * 1

Application and Function Instruction

The Dual Docking Station is with internal 500W pure sine wave inverter. Insert the battery into the plastic station and turn the power on. The inverter output is AC 110V 60Hz, being able to power products ≤ 500W. The product is equipped with functions like overload protection, short circuit protection, low battery level prompt and low battery over-discharge protection. It has a 1.7-inch LCD screen. While using, the screen will display the current battery level and overload icon prompts of battery A and battery B separately. The product is equipped with the equalization disk. When two batteries are inserted at the same time, the one with higher power level will be discharged first. When two batteries are in the same power level, they will be discharged equally at the same time. When the deviation value of two batteries is ≤2%, then both batteries work at the same time. When two batteries are working and plug out either of the battery, the output load will not be interrupted. This product also works when inserting one battery.

Product Main Structure Composition

The docking station is mainly composed of a sheet-metal base, battery plastic base, inverter, equalization disk and LCD screen.

Front of Docking Station

Rear of Docking Station

Operation and Usage

1. Check whether there is any visible damage to the appearance of the product and whether the output socket or the battery pins are loose or damaged (If abnormal conditions occur, stop using).
2. Confirm that whether the power of loaded device is within the specified range of the dual docking station. Then plug the device into the AC socket on the back of the product.
3. Plug the battery into the plastic battery compartment in the product.
4. Turn on the power switch. Then the device starts and the internal inverter works. The load should work normally. When the screen works normally, it shows that the corresponding battery is working.
5. When the product alarms a low-battery prompt, it should be turned off immediately and the battery needs to be replaced by a new one.

Product Maintenance

1. Socket contacts in the battery compartment are fragile so they should be inspected regularly. The deformed or cracked one should be replaced. Otherwise, it may cause charging failure.
2. Regularly remove dust and dirt from the heat dissipation window.
3. Regularly check whether the external screws and lifting rings of the chassis are fully tightened.

Troubleshooting

Issue: No Response When Power on

Suggested Action:

• Confirm whether the battery is completely inserted into the battery compartment and the sockets in the bottom of the battery should be completely connected to the battery station pins.
• Check whether the battery station pins are deformed or falling off.
• Make sure whether the battery is fully charged.

References

• Global Industrial - Industrial & Commercial Supplies

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>