Armacost 780002 ProLine Multi Color + Multi White LED Amplifier User Manual
- June 2, 2024
- Armacost
Table of Contents
Armacost 780002 ProLine Multi Color + Multi White LED Amplifier
Product Specifications
- Model Number: 780002
- Product Name: ProLine Multi-Color + Multi-White LED Amplifier
- Input Voltage: DC12V/24V
- Output Voltage: DC12V/24V
- Output Current: 6A per channel, total output max 15A
- Switching Rate: 10Mbps
- Working Voltage: DC12V/24V
- Output Mode: PWM constant voltage
- Overload Protection: Yes
Product Usage Instructions
Connections and Typical Applications
- Use LED amplifiers in conjunction with a color controller and an auxiliary power supply for large perimeter and array lighting applications.
- Connect multiple LED amplifiers to a single controller to control limitless lengths of lighting.
- Ensure each LED amplifier is connected to a separate power supply based on the power requirements of the LED lighting.
Power Supply Input
- Input voltage should be DC12V/24V.
- Connect the output to the lighting ensuring polarity is maintained (CH1 to CH1, CH2 to CH2, etc.).
Safety Protection
- The product provides overload protection.
Frequently Asked Questions (FAQ)
-
Q: Can the LED amplifier be used for both indoor and outdoor applications?
A: Yes, the LED amplifier can be used for indoor or outdoor applications when installed in a proper wet location enclosure. -
Q: What is the maximum rated output of the LED amplifier?
A: The LED amplifier is rated for up to 180 watts of 12-volt LED tape lighting or 360 watts of 24-volt LED lighting with no minimum load required.
ProLine Multi-Color + Multi-White LED Amplifier
- Use LED amplifiers throughout larger lighting designs, white or multicolor, with a single color controller to maintain color consistency and synchronization of any color-changing effect.
- Use in conjunction with a color controller and an auxiliary power supply for large perimeter and array lighting applications.
- Connect multiple LED amplifiers to a single controller to control limitless lengths of lighting.
- Professional-grade, high-capacity unit is rated for up to 180 watts of 12-volt LED tape lighting or 360 watts of 24-volt LED lighting. No minimum load is required.
- Suitable for indoor or outdoor use when unit is installed in a proper wet location enclosure.
- Uses proprietary high speed optocouplers that keep LED lighting colors and effects in synchronization regardless of the number of LED amplifiers installed.
Connections and typical applications
In large area applications the low-voltage wire that runs from the controller
to the LED lighting can sometimes be too long to carry adequate power due to
voltage drop. By integrating one or more LED amplifiers into the lighting
installation, you can repeat the signal from the controller to add lighting to
other areas.
IMPORTANT: This device amplifies or repeats the controller signal, not the power. Each LED amplifier installed will require a separate power supply. Output rating (watts) of the power supply connected to the LED amplifier is dependent on the power requirements of the LED lighting that is connected to the LED amplifier. Follow your LED tape model instructions to determine power supply requirements.
When a controller is wired directly to one or more LED amplifiers (not connected to LED lighting), the LED amplifiers and LED lighting can be located up to one hundred feet from the actual color controller. This can often solve voltage drop issues and may also help with certain installation needs. When a controller is direct wired to a LED amplifier, the cable will be transmitting only data, so a thick cable is not needed.
Perimeter Lighting Application 
Large Array Remote Installation Application
Safety protection
The amplifier has a function to prevent it from being damaged by mis-wiring,
output short circuit, overloading, or overheating. It will automatically shut
down under these extreme conditions until safe operating conditions are
restored. To avoid shutdowns, make sure the installed LED lighting
is compatible with constant voltage driving, is in the rated range of the
amplifier, and the cables are well connected and insulated. Also, install the
amplifier with proper ventilation and heat dissipation in mind.
SPECIFICATIONS
- Working voltage ……………..DC12V/24V
- Rated output current … 5x6A (15A max)
- Output mode …… PWM constant voltage
- Overload protection ……………………Yes
- Overheat protection ……………………Yes
- Working temperature ……….. -4°~140°F …………………………………(-20°~60°C)
- Dimensions ……………4.5 x 1.9 x 1.1 in. …………………………(115 x 48 x 27mm)
Manufactured in China
armacostlighting.com
© 2022 Armacost Lighting. All rights reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>