BEGA 51206.1 Indoor LED Pendant Luminaire Instruction Manual

Table of Contents

BEGA-51206-1-Indoor-LED-Pendant-Luminaire-fig-1

Product Name: Pendant luminaire downlight
Product Description: Cast aluminium luminaire housing with a velvet white finish. Reflector surface made of pure aluminium.
Weight: 1.5 kg
Energy Efficiency Class: D
This product requires an additional BEGA Installation component (accessory) for connection.
Luminaire without canopy.
Module connected wattage: 16.8 W
Luminaire connected wattage: 19.8 W
Colour temperature: 3000 K
Colour rendering index: CRI > 90
Module luminous flux: 2440 lm
Luminaire luminous flux: 1999 lm
Luminaire luminous efficiency: 101 lm/W

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning should be carried out by a qualified electrician.
The manufacturer does not accept liability for damage caused by improper use or installation.
If modifications are made to the luminaire, the person responsible for these modifications will be considered the manufacturer.
The luminaire can only be operated with an operating device that fulfills the requirements according to EN 61347-2-13.
The maximum idle voltage of 60 V DC must conform to SELV or SELV equivalent.
Avoid touching the light output opening of the LED directly during installation or relamping.
To install, screw the enclosed trim ring with the attached reflector into the luminaire housing by turning it clockwise.
To operate this luminaire, one of the following additional BEGA Installation components must be ordered – accessoire.
Refer to the instructions for use for the selected BEGA installation component for luminaire installation.

BEGA-51206-1-Indoor-LED-Pendant-Luminaire-fig-2

Ceiling luminaire downlight · indoor luminaire with broad spread light distribution.
BEGA Hybrid Optics® : Highly efficient and low-loss light distribution, thanks to reflector and optical lens.
BEGA System pendant luminaire for use in combination with various modular BEGA installation components.

Pendant luminaire downlight
Cast aluminium luminaire housing, finish Colour velvet white,
Reflector surface made of pure aluminium Optical silicone lens · BEGA Hybrid Optics® Trim ring · Chrome finish
Clear safety glass
Cable pendant · Sheath cable white 2 x 0,75@ Overall length of luminaire approx. 1500 mm Safety class III 3
c – Conformity mark
Weight: 1.5 kg
This product contains light sources of energy efficiency class(es) D
Luminaire without canopy,
for connection to an additional required BEGA Installation component (accessory)

Lamp
- Module connected wattage 16.8 W
- Luminaire connected wattage 19.8 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 35 °C
51 206.1 K3
- Module designation LED -0978/930
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 2440 lm
- Luminaire luminous flux 1999 lm
- Luminaire luminous efficiency 101 lm / W

Half beam angle 61°

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to
the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Please note:
The luminaire can only be operated with an operating device that fulfills the requirements according to EN 61347-2-13. The maximum idle voltage of 60 V DC must conform to SELV or SELV equivalent.

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Screw enclosed trim ring with attached reflector into the luminaire housing by turning it clockwise.
To operate this luminaire one of the following additional BEGA Installation components must be ordered – accessoire. Please refer to the instructions for use for the BEGA installation component selected for luminaire installation
Please note:
The manufacturer accepts no liability for damage caused by improper use or installation if no BEGA installation component is used to install this BEGA system pendant luminaire.

Clean luminaire regularly with solvent-free cleansers from dirt.

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by a qualified person using commercially available tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Close the luminaire.

BEGA Installation components with LED power supply unit. Satin white finish.
Depending on the desired type of installation, the following suitable installation components are available for this BEGA system pendant luminaire:
For all level ceilings:
- 13 238 Surface-mounted canopy (Type A) DALI · 220-240 V · 490 mA DC
- 13 266 Surface-mounted canopy (Type AS) Smart controllable / dimmable · 220-240 V · 490 mA DC
Suitable for level ceilings and sloped ceilings with a pitch of 0 – 40°:
- 13 244 Surface-mounted canopy (Type B) DALI · 220-240 V · 490 mA DC
- 13 250 Recessed canopy (Type C) DALI · 220-240 V · 500 mA DC
- 13 272 Recessed canopy (Type CS) Smart controllable / dimmable · 220-240 V · 500 mA DC
For flush and surface-mounted 3-phase Eurostandard-Plus® track systems:
- 13 218 Track adapter (Type D) DALI · 220-240 V · 500 mA DC