BEGA 50 085.1 Wall Luminaire for Indoor Use Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50 085.1 Wall Luminaire for Indoor Use Instruction Manual
Instructions for use
Application
Open and free-radiating wall luminaire · indoor luminaire with hand-blown opal
glass and metal housing. The character of the opal glass creates a smooth and
uniform light distribution in the room.
Product description
- Metal luminaire housing, finish Colour white
- Hand-blown opal glass 2 mounting holes Ø 6.5mm
- Distance apart 620mm
- Connection terminal 2.5@
- Earth conductor connection 2-pole connecting terminal for digital control
- LED power supply unit 220-240 V x 0/50-60 Hz
- DC 176-276 V
- During DC operation the LED power is reduced to 15%
- DALI-controllable
- Number of DALI addresses: 1
- Basic insulation is provided between the mains and control cables
- BEGA Thermal Control®
- Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
- Safety class I
- Safety mark
- Conformity mark
- Weight: 3.6 kg
- This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician. The manufacturer accepts no liability for damage
caused by improper use or installation. If subsequent modifications are made
to the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve an additional
protection against e.g. transients, etc. we recommend separate overvoltage
protection components. You can find them on our website at
www.bega.com.
Lamp
Module connected wattage 35.2 W
Luminaire connected wattage 40.4 W
Rated temperature ta=25 °C
Ambient temperature ta max=45 °C
50 085.1K3
Module designation 4x LED-0627/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 5580 lm
Luminaire luminous flux 4700 lm
Luminaire luminous efficiency 116,3 lm/W
Please note:
If the luminaire is to be mounted onto a metallic, electroconductive surface,
it is mandatory to make sure that the mounting surface is connected conductive
to the earth conductor of the luminaire
Installation
Only fix luminaire in position of application as pictured. For relamping, mounting and dismantling of the glass please keep a distance of 700 mm above the luminaire.
LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. Establish earth conductor connection and make the electrical connection to the terminals. For digital control please use the connecting terminal DA, DA. In case this terminal is not used the luminaire will be operated at full light output.Secure the luminaire housing to the installation surface with the fixing materials provided or other suitable materials. Note position of application “arrow down”. Loosen the knurled knob. Position glass into luminaire housing and fix it with the knurled knob.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
- Replacement of the LED module
- The designation of the LED module is noted on a label in the luminaire.
- The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
- The module can be replaced by qualified persons using standard tools.
- Disconnect the system and open the luminaire.
- Please follow the installation instructions for the
- LED module.
- Defective glass must be replaced.
- Close the luminaire.
Spares
Spare glass 11 003 229 .1RG
LED power supply unit DEV-0159/1050i
LED module 3000 K LED-0627/930
BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden ·
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>