bonsaii S123-A 6 Sheet Strip Cut Shredder Instruction Manual

bonsaii S123-A 6 Sheet Strip Cut Shredder

• THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
• PLEASE READ AND KEEP IT FOR FUTURE REFERENCE.
• Please give us a chance to make it right and do better! Contact our friendly customer service department for help first.
• Replacements for missing or damaged parts will be shipped.

IMPORTANT!

1. Please read and keep the manual for future reference.
2. Carefully read each step and follow the correct sequence of operation.
3. Please place the equipment on a flat and stable surface to prevent tipping over, as this may cause the machine to crack or become unusable.
4. The device should be placed as close as possible to an accessible wall outlet.
5. Do not disassemble, modify, or repair the device on your own to avoid electric shock, injury, or damage to the machine.
6. When you empty the basket, move the device, or do not need to use the device for some time, make sure the device is turned off and unplug the power plug to prevent fire or electric shock.
7. Do not use flammable liquids, gases, water, or cleaners to clean the device to avoid fire or electric shock.
8. Do not use the device in a high temperature, high humidity, or heavily dusty environment to prevent fire, electric shock, or machine malfunction.
9. Do not put tape, carbon copy paper, fabric, plastic film, etc. into the device for shredding to avoid damage to the machine.
10. Do not damage or process the power cord, and do not place heavy objects on the cable to avoid fire, injury, or electric shock.
11. If smoke or odor occurs during use, immediately turn off the power and stop using it to prevent fire or electric shock.
12. Do not use the shredder or power cord if it is damaged or defective to avoid fire or electric shock.
13. Do not shred greeting cards with sound chips or batteries to avoid fire or electric shock.

IMPORTANT SAFETY INTRODUCTIONS BEFORE FIRST USE

WARNING

• User information/safety instructions.
• Please do not allow children to use the machine.
• There are sharp blades inside the machine to avoid injury. Please be sure to exercise caution when using it.
• Please do not put your hand close to the shredder blades and the paper feed opening.
• There are sharp blades inside the machine to avoid injury. Please be sure to exercise caution when using it. Please do not let hair near the shredder’s feed opening.
• If your hair is accidentally sucked in, please use the “reverse function” to remove the danger.
• Please keep your clothing or some small items away from the feed opening of the paper shredder, such as ties, necklaces, sleeves, jewelry, etc.
• Please don’t use inflammable liquids, gases water and cleaner to clean the machine.
• To avoid fire accidents.
• Please kindly don’t touch the sharp edges to avoid injury.
• This equipment is not intended for use by children. Avoid touching the media feed opening with the hands, clothing, or hair.
• Unplug this equipment when not in use for an extended time, Hazardous moving parts are in this equipment, keep body parts away from moving parts.
• It cannot be over 6 sheets at one time for the quantity of shredding.
• One folded sheet of paper equates to 2 sheets of paper.
• Heavier paper, humidity, or other than rated voltage may reduce capacity.
• 85% Maximum sheets per pass to avoid jams.

WARNING

1. Bin Full:
   • The wastebasket will become full around 6-7 shredding passes (6 sheets per pass) of use. Empty the wastebasket when you see shred­ded materials fill the window to prevent paper jams.
   • Never let the wastebasket become full. This will lead to shredded materials being pulled back up into the shredder and cause jams.
2. No Trash bag:
   • If using a plastic bag to line the wastebasket, please remove it. This may cause the shredder not to operate properly.

Do not shred:

TECHNICAL SPECIFICATIONS

ONE FOLDED SHEET OF PAPER EQUATES TO 2 SHEETS OF PAPER

Heavier paper, humidity, or other than rated voltage may reduce shredding capacity.

OPERATION

1. Control switch
2. Power indicator light
3. Shredding slot
4. Handle
5. Basket

• Control Switch
  • Using the switch located on the unit, select one of the following settings by sliding the switch either left or right.
• AUTO:
  • This setting allows the shredder to be automatically started by inserting paper into the feed slot. Always feed the paper in as straight as possible. When the paper has passed through, the shredder will automatically stop.
• OFF:
  • This setting turns off all features of the shredder. For safety reasons, we recommend that you leave the shredder in the “Off” position whenever the shredder is unattended or not in use.
• REV(REVERSE):
  • In the unlikely event of a paper jam, the reverse setting can be used to help clear the cutters of paper that did not pass through. Never attempt to clear a jam by using the reverse function until you have emptied the wastebasket.
• JAM REMOVER /CREATED CARD DESTROYER:
  • Please slide the switch to this position and use hard paper like folded paper, postcards, or cardboard to push out the jammed paper. This allows you to manually activate the shredder into cutting mode.

LED Status Indicators:

• Ready(PowerOn):
  • The Blue LED light indicates the shredder is “On” and ready to operate when a paper is inserted.

Overheat:

Red light – The Shredder has shredded continuously beyond the maximum shred time and needs to cool down before the operation can restart. If this happens, switch the shredder off for 20 minutes or longer before resuming normal operation.

The proper way to use a shredder:

1. Do not insert fingers, ties, or other objects into the entry slot of the shredder.
2. Try to avoid laminating materials, plastic bags, etc. from being passed through the shredder. This will prevent damage to the cutters.
3. Do not shred wet paper as it can tangle in the cutters.
4. Do not shred more than the stated sheet capacity in one pass.
5. Do not break paper for more than 2 minutes at a time. Long-time use will make the motor overheat protection. If the motor is protected from overheating, it should be allowed to cool for at least 20 minutes before continuing to use it.
6. Do not use the “REV” function if you don’t need to.

Paper/ Credit Card Entry:

1. Make sure you don’t exceed the number of sheets at a time (Max. 6 sheets). Insert the paper as straight as possible into the shredding slot and release.
2. Insert one credit card at a time into the right of the feed slot.

NOTE:

1. Always turn off and unplug the shredder when not in use.
2. This shredder will shred staples and small paper clips. It is recommended that you remove paper clips whenever possible to extend the lifespan of your shredder.
3. Only by vertically inserting the credit card into the designated position of the entry slot and releasing it when shredding begins, can the credit card be shredded. Only one credit card can be shredded at a time.
4. Overfeeding the shredder: Shredding beyond the specified sheet capacity can result in extensive damage to the shredder. Overfeeding will strain the machine and quickly wear and break the cutting blades and internal components.

MAINTENANCE

Warning: Failure to properly maintain your shredder will void the warranty.

• Oil the shredder blades every month with basic vegetable, cooking oil, or shredder oil.
• Follow the oiling procedure below (FIGURE 1 ). It helps to keep the shredder blades operating well over many years of use.

Oiling procedure:

1. Turn off the shredder.
2. Apply shredder oil across the paper entry.
3. Turn the shredder in reverse mode for 3~5 seconds.

Note:

1. lubricating oil is NOT included.
2. basket not included

• Do not spray or keep any aerosol products in or around the shredder.
• DO NOT USE CANNED AIR ON THE SHREDDER.

CLEANING:

• ALWAYS UNPLUG THE SHREDDER BEFORE CLEANING!
• Only clean the shredder by carefully wiping the unit with a dry soft cloth or towel.
• Do not clean or immerse the shredder in water. Having the unit wet may result in damage or malfunction to the electrical components.
• If the shredder happens to get wet, be sure to completely dry the unit immediately with a cloth or towel.
• Never use anything flammable to clean the shredder. This may result in serious injury or damage to the product.

TROUBLESHOOTING

Solution:

• Please kindly check whether you used the machine with the related supply voltage or Plug-in again correctly.

Solution:

• When the waste bin is full, empty the shredded materials in the bin.
• Please slide the switch to the Jam Remover position and use hard paper like 3 sheets of folded paper, postcards, or cardboard to push out the jammed paper.

Solution:

• Please unplug first and use cotton swabs or needle-nosed pliers to take out the paper scraps.
• CAUTION please don’t overexert and use Sharp tools to clean or poke the mechanical sensor to avoid damaging the mechanical sensor.
• If the above answers can not solve your problems, please kindly contact our customer service team via email at customer-care@bonsaii.com

Disposal:

• Directive 2012/19/EU concerning the handing, collection, recycling, and disposal of A electrical and electronic equipment and their components (‘waste electrical and electronic equipment’, known as WEEE).
• The crossed symbol on a rubbish container indicates that the machine or device is not allowed to be disposed of but it must be handed over to a suitably equipped collection center for proper recycling or disposal.

Directives:

• This machine corresponds to the requirements according to EU Directive 2014/30/ entitled ‘Electro-Magnetic Compatibility’ and 2014/35/EU entitled ‘Low-Voltage
• The packaging materials have been selected for their environmental friendliness and ease of disposal and are therefore recyclable. Dispose of packaging materials that are no longer needed by applicable local regulations.

LIMITED WARRANTY

• Warranty Period: Machines are covered by a 2-year limited warranty and cutters are warranted for 2 years from the date of your original retail purchase from us. The warranty is not transferable to any subsequent purchaser or recipient of the product.
• We stand by our product and offer a 30-day money-back guarantee. During this time, you could return the item without paying any extra fee if there is a manufacturing defect in it. Please rest assured that the returns are free and easy if there is a manufacturing defect. Otherwise, it would be the customer’s responsibility to cover the shipping fee. Products on sale are also returnable.
• If the product isn’t meeting your expectations, please email within 30 days of receipt. We will help you to either return or exchange your product. Your original form of payment will be refunded in full once the full return is complete. After 30 days orders may be subject to a 20% restocking fee and all shipping and handling charges will be the responsibility of the customer. Additional return details are listed below. After 60 days the purchase from Bonsaii is non-refundable.
• If you receive a damaged product, you must notify Bonsaii within 48 hours of delivery. Bonsaii will investigate the claim and notify the freight company about the damage. Please retain all packaging if Bonsaii or the freight company needs to inspect it. These investigations may take several days but merchandise replacements will be processed as soon as possible.
• For product arrived defective or damaged, We’re sorry to hear that your Bonsaii product arrived in less than perfect condition. We’d like to resolve this issue right away with the help of our Customer Support Team and Quality Assurance team. They’ll need to know a bit of information on your order as well as the issue you’re experiencing with your Bonsaii product. To report your issue, please reach out to our Customer Support team by emailing customer-care@bonsaii.com with your order number. We may need you to make a short video, or take some pictures of the defects of the product and send them to customer-care@bonsaii.com. After a preliminary analysis of the video or pictures, we will send you a brand-new replacement right away if it is confirmed to be defective on its arrival. If we determine that you have misrepresented the Bonsaii product’s condition and that the product is not defective, we will send you the right instructions and help you to use the product correctly.
• In line with our policy of continuous development, we reserve the right to change this product, packing, and documentation specification without notice.
• If you have any questions or any confusion, Please kindly contact us: at customer-care@bonsaii.com.
• Manufacture: Bonsen Electronics Limited 0: No.11-12, Lun Pin Chong Industrial Zone San Tun
• Community, Hou Jie Town 523941 Dongguan City,
• Guangdong PEOPLE’S REPUBLIC OF CHINA
• customer-care@bonsaii.com
• EU BRIDGE ADVISORY GMBH Virginia Str. 2
• 35510 Butzbach,Germanyeubridge@outlook.com
• EU BRIDGE ADVISORY GMBH Virginia Straf3e 2,
• 3551 O Butzbach, Deutsch landeubridge@outlook.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>