BEGA 33 788 House Number Luminaire Instructions
- June 12, 2024
- BEGA
Table of Contents
Technical amendments reserved
House number luminaire
Instructions
33 788 House Number Luminaire
Instructions for use
Application
House number luminaire with automatic twilight switch for one up to three-
digit numbers or letters.
A luminaire made of aluminium alloy and crystal glass.
Product description
Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Crystal glass, white inside with 1-2 digit numbers lettering height 120 mm or
with 3 digit numbers lettering height 75 mm
Silicone gasket
Integrated twilight switch with potentiometer for infinitely variable
adjustment 2 mounting holes ø 5 mm
Distance apart 70 mm 2 cable entries for through-wiring of mains supply cable
ø 7-10.5 mm
Connecting terminal and earth conductor terminal 2.5@
LED power supply unit
230 V y 50/60 Hz
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK06
Protection against mechanical impacts < 1 joule
– Safety mark
**** – Conformity mark
Weight: 3.4 kg
This product contains light sources of energy efficiency classes D, E
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
| Module connected wattage | 6.8 W |
|---|---|
| Luminaire connected wattage | 8.5 W |
| Rated temperature | ta = 25 °C |
| Ambient temperature | ta max = 45 °C |
33 788 K3
| Module designation | LED-0736/830 |
|---|---|
| Colour temperature | 3000 K |
| Colour rendering index | CRI > 80 |
| Module luminous flux | 1135 lm |
| Luminaire luminous flux | 182 lm |
| Luminaire luminous efficiency | 21,4 lm / W |
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Undo lateral hexagon socket head screws on luminaire housing as far as they
will go.
Swivel out luminaire housing.
Aperture angle: 100°.
In order to avoid an optical feedback (flashing operation of the luminaire)
the distance between the photodiode of the twilight switch and reflecting
objects must be min. 15 cm.
Lead the mains supply cable through the cable entry into the luminaire back
housing.
Note position of application of the luminaire “arrow down”.
Fix luminaire base with enclosed or any other suitable fixing material onto
the mounting surface.
Be sure to use the gasket rings supplied.
Make the earth conductor connection and the electrical connection.
In order to guarantee the maximum service life of the electrical components,
the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the
position marked by the red information label immediately before finally
closing the luminaire.
The switch-on and switch-off values of the twilight switch can be infinitely
variable adjusted by the potentiometer.
The complete adjusting range corresponds to 30 rotations (no stop).
The delivery condition of the potentiometer is positioned half-way so that one
can turn 15 cycles clockwise or anti-clockwise to cover the complete adjusting
range.
Swivel luminaire housing onto the luminaire base, press-on strongly and fix
with hexgon socket head screws.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
When ordering spare glasses please advise figures or symbols.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Spares
| Spare glass | 11 002 861 11 |
|---|---|
| Twilight switch | 61 000 515 |
| LED power supply unit | DEV-0451/350 |
| LED module 3000 K | LED-0736/830 |
| LED module 4000 K | LED-0736/840 |
| Gasket twilight switch | 83 000 297 |
| Gasket housing | 83 000 956 |
| Gasket glass | 83 000 978 |
BEGA Gantenbrink-Leuchten KG · Postfach 31 60
· 58689 Menden
· info@bega.com
· www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>