Miele PFD 104 SCVi Integrated Dishwasher with 3D MultiFlex Cutlery Drawer Installation Guide
- June 1, 2024
- Miele
Table of Contents
PFD 104 SCVi
Installation plan
Installation notes
For safe installation and commissioning of the dishwasher please read the
installation plan, the service documentation, the installation sheet and the
operating instructions.
This installation plan includes the dimensions of the appliance, the technical
data and the requirements to be met on site for the installation of the
dishwasher.
Installation requirements
This dishwasher must only be installed and commissioned by the Miele
Customer Service Department, a Miele authorised dealer or a suitably qualified
specialist.
Installation should only be performed in accordance with valid regulations,
relevant standards and health and safety codes.
Environmental requirements
Condensate can build up in the area surrounding the dishwasher. Any
furniture and fittings in the room must therefore be suitable for purpose.
Vapour barrier film for built-in appliances
The vapour barrier film supplied protects the worktop from damage caused by
steam when the door is opened. Attach the vapour barrier film above the door,
underneath the worktop.
Electrical connection
All work on the electrical connection must be carried out by the Miele
Customer Service Department, an authorised Miele dealer or a qualified
electrician.
Plug connection
The dishwasher should be connected to the electricity supply via a socket.
Hard-wired
If the dishwasher is hard-wired to the power supply, a power switch capable
of disconnecting the dishwasher at all poles must be installed on site. This
power switch must have a contact gap of at least 3 mm.
The socket and the power switch must be accessible after the appliance has
been installed. An electrical safety test must be carried out after
installation and after any servicing work. The mains connection cable must be
laid protected from the risk of thermal damage.
Residual current device (RCD)
For increased safety, it is recommended to protect the dishwasher with a
residual current device (RCD) with a trip current of 30 mA.
Equipotential bonding
There is a screw connection point for equipotential bonding at the back of the
dishwasher. Equipotential bonding should be carried out if possible on site.
Water connection
The dishwasher must only be connected to fully vented pipework. A brief
increase in the water pressure can damage components of the dishwasher.
Water inlet
The quality of the incoming water must correspond to the drinking water
specification of the country in which the dishwasher is being operated.
The dishwasher must be connected to the water supply in strict accordance with
current local and national water authority regulations. It can be connected to
cold or hot water supplies. Connecting the dishwasher to a hot water supply
will reduce programme running times. For short programme running times, a
water pressure of at least 200 kPa is also required.
Regulation in Germany:
For the protection of drinking water, the non-return device supplied with the
dishwasher must be installed between the stopcock and the water inlet hose.
Screw a non-return device onto the stopcock. Then screw the water inlet hose
with the water protection system onto the thread of the non-return device.
If a stopcock is not available, only a qualified installer may connect the
dishwasher to the drinking water supply. The stopcock should remain accessible
once the dishwasher has been installed so that the water supply can be shut
off whenever the appliance is not in use.
Drain
The dishwasher drain hose should be connected to a separate on-site drainage
system for the dishwasher only. If a separate connection is not available, we
recommend connecting the hose to a dual-chamber siphon.
If the hose is to be fitted directly to the drainage system on site, use the
hose clip supplied with the dishwasher.
The on-site connector for the drain hose can be adapted to different hose
diameters. If the connector extends more than 30 mm into the drain hose, it
must be shortened. Otherwise, the drain hose can become blocked.
Lay the drain hose so that it does not kink and is not being subjected to
pressure or tension.
If the on-site drain connection is situated lower than the guide path for the
lower basket rollers in the open door, a siphoning effect during a programme
can cause the wash cabinet to empty itself of water.
In this case, lay the drain hose with a bend in it so that its highest point
is at least level with the guide path for the lower basket rollers. For AU, NZ
the drain should be connected in accordance with AS/ NZS 3500.2.
External dispensing
An external dispensing module for liquid cleaning agents can be connected to
the back of the dishwasher. The dispensing module is available as an optional
accessory and is supplied with installation instructions.
Appliance dimensions and installation dimensions
PFD 104 SCVi
Front panel dimensions
| Min./max. length | [mm] | 690–810 |
|---|---|---|
| Min./max. thickness | [mm] | 16–20 |
| Min./max. weight | [kg] | 5–12 |
Connections
Connections on the back of the appliance
On-site connections
| 1 | Electrical connection |
|---|---|
| 2 | External dispensing, power supply connection |
| 3 | Equipotential bonding |
| 4 | Waste water |
| 5 | Cold or hot water |
| 6 | External dispensing, connection for dispensing hose sealed with a blind |
stopper*
- the dispenser connector is supplied with the dispensing module
External dispensing
| Max. delivery head | [m] | 1.5 |
|---|---|---|
| Length of dispenser hose, DOS module to suction lance | [m] | 1.8 |
| Length of dispenser hose, back of appliance to DOS module | [m] | 2.8 |
| Length of power cable, back of appliance to DOS module | [m] | 2.8 |
Place the container on the floor next to the cleaning machine or in an
adjacent cabinet.
The container must not be placed on top of or above the cleaning machine.
Technical data
Dimensions and weights
| Height | [mm] | 845 |
|---|---|---|
| Height adjustment | [mm] | 65 |
| Width | [mm] | 598 |
| Depth | [mm] | 570 |
| Depth with door open | [mm] | 1205 |
| Max. plinth return | [mm] | 115 |
| Weight | [kg] | 51 |
| Max. floor load | [N] | 1000 |
Emission values
| Sound power level | [dB(A) re 1 pW] | 45 |
|---|---|---|
| Sound pressure level in the workplace | [dB(A)] | 32.5 |
Electrical connection
Standard electrical connection PFD 104 SCVi
| Voltage | 3N AC 400 V | |
|---|---|---|
| Frequency | [Hz] | 50 |
| Fuse rating | [A] | 16 |
| Plug | 1,7 | |
| Power cable length | [m] | |
| Power cable cross-section | [mm2] | 5 x 2,5 |
| Heat output | [kW] | 7,1 |
| Total rated load | [kW] | 7,3 |
Standard electrical connection , Possible voltage variant PFD 104 SCVi
| Voltage * | AC 230 V | |
|---|---|---|
| Frequency | [Hz] | 50 |
| Fuse rating | [A] | 16-Oct |
| Plug | Typ-F | |
| Power cable ** length | [m] | 1,7 |
| Power cable cross-section | [mm2] | 3 x 1,5 |
| Heat output | [kW] | 1,9 |
| Total rated load | [kW] | 2,1 |
- Programme running times are longer with this voltage variant
Optional accessory
Water inlet**
| Max. water temperature | [°C] | 60 |
|---|---|---|
| Max. water hardness | [mmol/l] | 6.5 |
| Max. water hardness | [°dH] | 36 |
| Water connection pressure | [kPa] | 100 – 1000 |
| On-site threaded union (flat seal) | [inches] | 3/4 |
| Connection hose length | [m] | 1.5 |
| Connection hose extension * | [m] | 1.5 |
- Optional accessory
Drain
| Max. water temperature | [°C] | 82 |
|---|---|---|
| Drain hose length | [m] | 1.5 |
| Max. drain hose length | [m] | 4 |
| Max. delivery head | [m] | 1 |
| Max. transient flow rate | [l/min] | 10 |
| Hose inner diameter | [mm] | 22 |
| On-site hose sleeve (Ø x length) | [mm] | 22 x 30 |
Operating conditions
| Ambient temperature | [°C] | +5 – +40 |
|---|---|---|
| Relative humidity: | ||
| Up to 31 °C, maximum | [%] | 4000 |
| Linear decreasing to 40 °C | [%] | 80 |
| Max. altitude above sea level up to | [m] | 50 |
Storage and transportation conditions
| Ambient temperature | [°C] | -20 – +60 |
|---|---|---|
| Relative humidity | [%] | 10–85 |
| Air pressure | [hPa] | 500–1060 |
Min. site access dimensions including transport pallet
| Height | [mm] | 970 |
|---|---|---|
| Width | [mm] | 670 |
| Depth | [mm] | 670 |
France :
MIELE S.A.S – Z.I. du Coudray – 9, av. Albert Einstein – B.P. 1000
93151 Le Blanc-Mesnil Cedex –
www.miele.fr/professional
R.C.S. Bobigny B 708 203 088
Contact Service Commercial
Tél. : 01 49 39 44 44 – Fax : 01 49 39 44 38 – Mail :
advpro@miele.fr
Contact SAV Professionnel (Intervention)
Tél. : 01 49 39 44 78 – Fax. : 01 49 39 34 10 – Mail :
savpro@miele.fr
Contact Support Technique (Hotline)
Tél. : 01 49 39 44 88 – Mail :
support.technique@miele.fr| Italia:
Miele Italia S.r.l.
Strada di Circonvallazione, 27
39057 S. Michele-Appiano (BZ)
Internet: www.miele-professional.it
E-mail: info@miele-professional.it
---|---
België / Belgique:
nv Miele België / S.A. Miele Belgique
Z.5 Mollem 480 – 1730 Mollem (Asse)
Tel. 02/451.15.40
E-mail: professional@miele.be
Internet: www.miele-professional.be|
Agenzie e centri di assistenza tecnica autorizzati
Miele in tutte le regioni italiane.
Tel. Contact Center Professional:
0471-666319
Lunedì – Venerdì ore 8-20
Sabato ore 9-12/14-18
Ireland:
Miele Ireland Ltd.
2024 Bianconi Avenue
Citywest Business Campus
Dublin 24
Tel: (01) 461 07 10, Fax: (01) 461 07 97
Email: info@miele.ie
Internet: www.miele.ie| Schweiz:
Miele AG
Limmatstrasse 4, 8957 Spreitenbach
Miele SA
Sous-Riette 23, 1023 Crissier
Telefon: 0848 848 048
www.miele.ch/contact
www.miele.ch
España:
Miele S.A.U.
Avda. Bruselas, 31, 28108 Alcobendas (Madrid)
Tfno.: 902 575 175, Fax: 91 662 02 66
Internet: www.miele-professional.es
E-mail: miele@miele.es| Nederland:
Miele Professional
De Limiet 2, Postbus 166, 4130 ED VIANEN
Afdeling Customer Service Professional
Tel.: (03 47) 37 88 84, Fax: (03 47) 37 84 29
E-mail: professional@miele.nl (verkoop &
algemene vragen)
E-mail: serviceprofessional@miele.nl
(service & onderhoud)
Website: www.miele-professional.nl
Portugal:
Miele Portuguesa, Lda.
Av. do Forte, 5, 2790-073 Carnaxide
Telf. 21 4248 100, Fax 21 4248 109
E-Mail: professional@miele.pt
Website: www.miele-professional.pt|
Luxembourg:
Miele S.à.r.l.
20, rue Christophe Plantin
Boîte Postale 1011
L-1010 Luxembourg/Gasperich
Téléphone: 49711-29, Téléfax: 49711-39
E-mail: infolux@miele.lu
Internet: www.miele.lu
Manu facturer: Miele & Cie. KG, Carl-Miele-Straße 29, 33332
Gütersloh, Germany
**** Änderungen vorbehalten/2023-08-04
M.-Nr. 11 673 380 / 02
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>