Maxx Air CX10XXSOL Solar Powered Roof Exhaust Fan Installation Guide
- September 26, 2024
- MAXX AIR
Table of Contents
Maxx Air CX10XXSOL Solar Powered Roof Exhaust Fan
For normal sloped, asphalt shingle or wood shake roofs.
Also works well with flat concrete tile, slate or metal roofs.
Before beginning the installation of your new Solar Powered Roof Exh·aust Fan, please read through the entire installation instructions and contact us if you, have any questions.
TOOLS REQUIRED
- Ladder
- Reciprocating saw (or jig saw)
- Power drill with a 1/2” – 1” drill bit
- 1” – 2” deck screw and screw bit
- Hammer & roofing nails (or self tapping galvanized screws)
- Caulk gun with waterproof roofing sealant
- Measuring tape
- Permanent marker (or chalk/ crayon)
- Roofing knife (or box cutter)
- Flat pry bar
8 Steps Installation Istruction
It is advised that you prepare the mounting hole prior to bringing the fan up
on the roof.
Always secure the fan on the roof to avoid injury or having the fan slide off
the roof and get damaged.
Step 1 -Ventilation Clearance
To maximize the solar fan’s effectiveness, you’re suggested to remove or block
any existing rooftop static vents and ridge vents. If there is already a
turbine-type vent, simply remove the old vent and use the same hole for the
new installation, or block it completely. (fig. 1}
*Make sure you have proper intake ventilation at the eave or fascia. Use a ratio of 1 sq. ft. of intake ventilation for every 600 sq. ft. of attic space.
Step 2 -Positioning the Solar Fan
For optimum performance, position the solar fan due south or southwest, and
position it on an area of roof where the sun is not shaded or blocked, to
capture direct sunlight and extended sunlight periods throughout the day.
(fig. 2}
Then pitch upon the position that is 18 -24 inches from top of the roof peak
and as close to the mid-point of your house as possible.
In the case that 2 or more fans are getting installed, each fan should be
separated by at least 15 feet to optimize ventilation.
Step 3 – Marking the Ventilation Hole
From inside the attic, measure approximately 18-24 inches down from the roof
peak and center this spot between two rafters (fig. 3-1). Through this mark,
drill a screw into the plywood and roof shingle to have it located from on top
of the roof.
Cut a template cardboard at same size as the air duct’s, then puncture it from
center hole over top of the screw, and trace a circle around outer edge of the
template with any marker for a circle at 12” or 14” diameter.
(fig. 3-2)
Alternatively, you can make use of a 6” or 7” cotton thread and strap a pen at the edge of it. Then move the pen to draw a circle same at 12” or 14” diameter.
Step 4 – Cutting the Hole
Bore a pilot hole with your power drill anywhere along inside of the· marked
circle. Then insert the saw blade into that pilot hole, and cut a complete
hole into the
roof following the circle pattern. (fig. 4)
NOTE
- Do not cut through any roofing rafters or framing materials. Only cut and remove the roof sheeting and shingles.
- Prior to cutting the hole, make sure there is no wires or waterlines in the area that you are cutting.
- Try to secure the removed materials before completely cutting out the circle, so that they do not fall into the attic space.
Step 5 – Lifting the Shingles to Slide Up the Attic Fan
To slip the solar fan smoothly on top of felt paper and underneath shingles on
the roof, the nails located 5” above and to the side of that hole will need to
be removed. Use a pry bar or reciprocating saw to loosen or cut those nails.
(fig. 5-1}
In some cases, the builder may have used large washers to install the felt
paper, if it does not slide easily into place when slipping the solar fan, a
nail is most likely blocking the bottom. In this case, lift up on the shroud
cover slightly to position the solar fan directly over the hole and under the
shingles. (fig. 5-2)
Step 6 -Securing the Solar Fan
Mark and pre-drill some visible holes on the bottom board, then get some
proper screws or nails and drive them through those holes to secure the solar
fan to the roof. After then, apply waterproof roofing sealant to the screw
heads to prevent water percolation. (fig. 6)
Any shingles that remain loose should be fixed as well, use roofing nails to
secure them and apply waterproof roofing sealant to the backside of shingles
or the nail heads that have been added.
Step 7 (for those solar panel adjustable models only) – Installing the Angel Adjustment Bracket
Attach the provided screws and brackets left from package box to the unit. Install the angle adjustment brackets by securing one end to the regulating plate and the other end to the solar panel frame. {fig. 7)
- This fan has the solar panel adjustment design at 3 angles: 15°1 30° & 45°1 set the angle properly to capture most direct sunlight in your area.
- The fan also has a horizontal adjustment platform design for the solar panel turning from 1 ° to 90°1 regulate the solar panel direction for it to enjoy the all-day sunbath.
Step 8 (for those solar panel adjustable models only).Adjusting the Solar Panel
The fan’s solar panel should be adjusted to maximize exposure to the sun’s path during the day. The optimal adjustment is to have the panel 90° to the midday path of the sun.
You can re-adjust the panel during winter or summer seasons if desired.
CAUTION
- This solar fan will start working automatically whenever the sun shines on the solar panel, so it’s always wise to exercise caution when approaching the fan.
- Use appropriate attire or equipment, like safety glasses, gloves, hard hats etc. during operation to avoid accidents.
- Installation work and electrical wiring must be done by qualified persons and in accordance with all applicable building codes and standards, including fire requirements.
- To prevent back drafting of any fuel-burning equipment in the attic, sufficient air is needed for proper combustion and exhausting of gases through the flue of fuel-burning equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>