BEGA 84 085 Recessed Floor Lamp Instructions

: June 12, 2024
: BEGA

Table of Contents

BEGA 84 085 Recessed Floor Lamp
Product Usage Instructions
Instructions for use
Product Description
Safety
Installation
Accessories
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 84 085 Recessed Floor Lamp

Product Information:

The product is an in-ground luminaire with symmetrical light distribution directed upwards. It is designed for accentuated illumination of private gardens and is resistant to foot traffic.
The luminaire can be installed flush in soil, lawn, or gravel.
However, it must not be overrun by vehicles.

The product has a module designation of 84 085 K3. It has a colour temperature of 3000 K and a colour rendering index (CRI) greater than 80. The module has a luminous flux of 940 lm, while the luminaire has a luminous flux of 683 lm. The luminaire’s luminous efficiency is 115.8 lm/W.
The product operates at a connected wattage of 4.8 W for the lamp module and 5.9 W for the luminaire. It has a maximum rated temperature of 25°C and can be installed in heat-insulating material.
The luminaire is equipped with overvoltage protection in accordance with DIN EN 61547. However, for additional protection against transients, it is recommended to use separate overvoltage protection components available on the manufacturer’s website.
There is also a desiccant bag inside the luminaire housing that should not be removed as it helps remove residual moisture.
The product comes with accessories such as a distribution box for installation in soil (70 730) and a distribution box with 7 cable entries. There are also connection terminals (5 x 4@) available.
For replacement parts, the following are available: spare glass (14 001 394), LED power supply unit (DEV-0451/350), LED module 3000 K (LED-0336/830), reflector (76 001 874), gasket glass (83 001 893).

Product Usage Instructions

Ensure the luminaire is installed in soil, lawn, or gravel and not overrun by vehicles.
Do not remove the desiccant bag from the luminaire housing.
If the LED module needs replacement, refer to the label in the luminaire for the designation. The replacement module should have the same light colour and light output as the original module. Qualified persons should use standard tools for replacement and avoid touching the light output opening of the LED directly during installation or relamping.
If additional protection against transients is desired, consider using separate overvoltage protection components available on the manufacturer’s website.

In-ground luminaire

Instructions for use

Application
In-ground luminaire with symmetrical light distribution directed upwards for accentuated illumination of private gardens.
Luminaire resistant to foot traffic for flush installation in soil, lawn or gravel.
Luminaire must not be overrun by vehicles.

Product Description

Luminaire housing made of glass-fibre reinforced synthetic
Cover ring made of stainless steel
Steel grade no. 1.4301
Clear safety glass
Reflector surface made of pure aluminium 1,8 m water-resistant connecting cable 07RN8-F 3 G 1@ with implemented water stopper and 1.2 m PVC cable conduit
LED power supply unit 220-240 V x 0/50-60 Hz
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 67
Dust-tight and protection against temporary immersion
Pressure load 150 kg (~1,500 N)
Impact strength IK09
Protection against mechanical impacts < 10 joule
– Safety mark
– Conformity mark
Weight: 1.2 kg

This product contains light sources of energy efficiency classes C

Lamp

Module connected wattage 4.8 W
Luminaire connected wattage 5.9 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 50 °C
When installed in heat-insulating
material ta max = 30 °C

84 085 K3

Module designation LED-0336/830
Colour temperature 3000 K
Colour rendering index CRI > 80
Module luminous flux 940 lm
Luminaire luminous flux 683 lm
Luminaire luminous efficiency 115,8 lm / W

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
We recommend fuse protection via a residual current circuit breaker to be provided by the customer.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Installation

Sufficient drainage (e. g. gravel, stone chippings) must be provided under the luminaire.
0.3 m of cable should be left under the luminaire housing so that the luminaire could be removed during maintenance work.
Insert the luminaire flush into the soil surface. To protect the luminaire connecting cable from damage push the enclosed cable conduit over the cable.
The electrical connection at the luminaire connecting cable must be carried out on site according to the protection class and safety class.
We recommend to use a distribution box 70 730 or 71 053.

Cleaning · Maintenance

After installation, the luminaire should first be cleaned. Building dust, residues from contact adhesives, paint splashes and rust film must be completely removed. Never use high pressure cleaners and cleaning implements made
of normal steel, steel brushes or steel wool because they cause extraneous rust to form. When using stainless steel cleaners, please read the directions carefully.
Cleaning agents containing hydrochloric acid and chlorides should never be used.
We recommend cleaning the luminaires regularly.

Please note:
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.

Disconnect the system.

Lift luminaire out of the ground surface and place it with the glass side facing downwards onto an even and clean underlay.
Undo hexagon nuts and lift luminaire housing. LED modules can be replaced now.
Please follow the installation instructions for the LED module.
Check all hexagon nuts and threads thoroughly and grease them.
Check the gasket and replace, if necessary. A broken glass must be replaced.

Insert reflector.