Lofree OE907 1 Percent Fresnel Dual Mode Mechanical Keyboard User Manual

OE907 1 Percent Fresnel Dual Mode Mechanical Keyboard
User Manual

Charge

1. When the power of this product is lower than 10%, the power indicator 4 will flash white. please use the standard Type-C cable to charge.

2. During the charging process, the power indicator is always on in white; when the battery is fully charged the power indicator is off.

Note: Plug the Type-C cable into the SB port of the computer to complete the charging of the product (the product can be charged in the Bluetooth/wired/off state)

Use of Bluetooth/Wired Mode

wired mode

1. Witch to the ON position.
   Note
   In wired mode, the keyboard will not automatically enter power-saving mode.

2. Take out the Type-C cable that comes with this product, connect the keyboard to the computer, and complete the wired connection mode.
   

System switch (Mac/iOS, Windows/Android dual system switching}

1. Mac/iOS system Switch to the Mac/iOS system, which matches the Mac/iOS system and usage habits.

2. Windows/Android system Switch to Windows/Android system, which matches Windows/Android system and usage.

Bluetooth connection mode

1. Switch to the “BT” position

2. Long press Fn+Q/ Fn+W/ Fn+E until the indicator light flashes slowly

3. Turn on the Bluetooth function of your device, search for “l% Lof- ree” and connect.

4. the indicator light is always on after a successful connection

5. short press Fm+Q/ Fm+Fn+f to switch different devices

6. Switch to the “OFF” position, the product closes all modes at this time but can be charged.

Adjustment of light effect

1. Switch light effect
   Short press Fm+Backspace n the upper right corner, switch light effect mode→ l light effect mode 2→­ model repeat in turn

2. Light effect ON/OFF
   Long press Fm+Backspace for 2s in the upper right comer to open/close light
   Note the light effect stays on by default.

3. Adjustment of light brightness Short press Fn+ fin the upper right corner to increase the light brightness.
   Short press Fm+ Jin the upper tight corner to decrease the light brightness
   There are four types of brightness:06, 406,706,1009%
   Note: The default brightness is 40% when starting up (L.If the brightness is adjusted to 09%, it is forcibly adjusted t0 409%
   when the lighting effect is activated 2. f the current is other 70% and 100% brightness, follow the current brightness)

4. adjustment of light flashing frequency Short press the Fn+- in the upper right corner to decrease the frequency.
   Short press Fn+ -in the upper right corner to increase the frequency

Note: There are 4 kinds of frequency, low power state, light effect off

Multimedia and function keys

Fn+ESC in the upper right corner…= the function keys

Fn+1 in the lower right corner…= the multimedia keys

NAME AND CONTENT OF HAZARD­ OUS SUBSTANCES IN PRODUCT:

Harmful
Elements| Hazardous substances
---|---
Lead
(Pb)| Mercury
(Hg)| Cadmium
(Cd)| Hexavalent
Chromium
(Cr, VI)| Polybrominated-
ed Biphenyls
( PBB )| Polybrominated
Diphenyl Ethers
( PBDE )
Plastic
Components| 0| 0| 0| 0| 0| 0
Circuit Board
Assembly| 0| 0| 0| 0| 0| 0
Silicone
Components| 0| 0| 0| 0| 0| 0
Spare Parts| 0| 0| 0| 0| 0| 0

This table is prepared in accordance with the provisions of SJ/T 11364
The classification and marking of this product were performed in accordance with the EU directive 2011/65/EU and the revised 0directive 2015/863/EU

O: Indicates that the said hazardous substance contained in all the homogeneous materials for this component is below the limit requirement in GB/T 26572
X: Indicates that this hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in GB/T 26572

ENVIRONMENTAL PROTECTION INSTRUCTIONS:
The hazardous substances contained in the electronic parts of this product will not leak or change under normal use conditions for a period of ten years. During the same period, the electronic components of this product will not cause serious environmental pollution, or serious. damage to human health or property white the products are being used by the consumer According to the Chinese electronic industry-standard SJ/T 11364-2014 and related Chinese government regulations, this product and some of its internal or external components may have an environmentally friendly use period mark, depending on the component and component manufacturer, the mark lifespan on the product and its components may vary. The expiration the date on the component takes precedence over any conflicted or different UF UP [abelson the product

Warning

• 11 the battery is not replaced properly, there may be leakage or explosion and personal injury hazards.
• Do not use the battery when there is leakage, discoloration, deformation, or any other abnormality.
• Do not leave the battery in a discharged or unused state for a long time.
• Do not short-circuit the product
• Battery life varies with usage. Used batteries should be disposed of in accordance with local laws or thrown away in trash cans for recycling electronic devices.
• If any liquid accidentally enters the product, please immediately disconnect the power supply and remove the product. Continue to use the product may cause fire or electric shock. Please contact the agent or the nearest customer service center for inspection and maintenance.

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec­tion against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communi­cations. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver,
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with pant 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device  must accept any interference received, including interfering ence that may cause undesired operation
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction

Service Hotline
4006002083
www.lofree.com.cn www.lofree.co
lofree.co lofreecolofree.co

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>