Tranya S2 Smart Watch User Manual

: June 4, 2024
: Tranya

Tranya S2 Smart Watch

Get Started

Package list

Replace the band

① side button: Power on/off; back to the last interface
② side button: Power on; switch to training interface

If you buy new bands and want to replace, firstly, flip the switch and
take out the wrist band, then pick up the band you like, and flip theswitch into the end of the watch until you hear a click and then snaps into place.
Note: Pay attention to the position of the long and short band and the display screen, do not install them upside down.

Charge your watch

Connect the USS-charging cable with the watch according to the picture.
When the device is connected to the power supply, it will vibrate.

Wearing

Wear the device with a finger’s distance from the wrist bone and adjust the tightness of the wrist band to a comfortable position.

Power on/off

Long press the button on the upper right for 4-5 seconds to power on. Or charge it to power on.
Switch to the Off interface, and press it to power off. Or press the button on the upper right for 4-5 seconds in the main interface to power off.

Install the App

1. Open your App store and search “GloryFit” to install.
2. Or scan the following QR codes to install “GloryFit”. The QR code can be found in the Settings.

Personal information and exercise goals

Open the App GloryFit to set your personal information.
Setting your avatar, name, gender, age, height and weight, which can help to increase the accuracy of the monitoring data.
Set your daily exercise goals.

Device connection

Before connecting, ensure the following matters:

The watch is not directly connected to the Bluetooth of the mobile phone. If so, please delete the “S2” from the Bluetooth list of your mobile phone.
The watch is not connected to other mobile phones. If so, please unbind the watch from other mobile phones. (If the original phone is an iOS system, you also need to delete the “S2” from the Bluetooth list of the phone).
The distance between the mobile phone and the watch should be less than 1m.

Then follow the below steps to connect your smart watch:

Step 1: Turn on the Bluetooth in your phone;
Step 2: 0 pen the .. Glory Fit” in you r phone ;
Step 3: Click “Device”;
Step 4: Click “Add a new device”;
Step 5: Click “Select device”;
Step 6: Select the product model – S2;
Step 7: Click “Pair” to complete the connection.

Note: If you can’t find “S2” in step6, please check whether the device has been selected in the Bluetooth list of your mobile phone. If so, please click “Ignore S2” and search again.

Operation

Raise your hand or the button on the upper right to light up the screen.
The screen will turn off without operations in 10 seconds by default.
You can modify this default value in the smart watch.
The heart rate monitoring function is on by default. You can turn it off in the GloryFit.
The blood oxygen function is off by default. You can turn it on in the GloryFit.
Press the button on the upper right at any time to return back.

Data synchronism

The watch can store 7 days of off-line data, and you can synchronize the data on the App homepage manually. The more data, the longer synchronization time is, and the longest time is about 2 minutes.

GloryFit App functions and settings

Notification

Call reminder
You can one-click the pink icon to hang up the call.
SMS reminder
App reminder
You can add reminders of App messages in the GloryFit, such as Twitter, Facebook, WhatsApp, lnstagram and other application messages.

Note:

Be sure to turn on both of the functions and their permissions in the GloryFit.
The watch only can display 80 characters for iOS and Android per message.
If your watch doesn’t receive any message, please refer to the FAQ at the end of the manual.

Physical health

Heart rate monitoring
The heart rate monitoring function is on by default. You can turn it off in the GloryFit .
Blood oxygen setting
The blood oxygen function is off by default. You can turn it on in the G loryFit.
You can set the time and period of blood oxygen monitoring accord it ng to your needs. 1-H is the recommended cycle for blood oxygen monitoring.
Note: Heart rate monitoring will be suspended when monitoring blood oxygen, and vice versa.
Sedentary reminder
You can set the start time, end time and reminder interval of sedentary reminder according to your needs.
Physiological cycle
Female function is only available after you finish the following steps in the GloryFit.
Physiological Cycle-Fill in your period information-Start

General function

Note: For the following operations, the word expressions of IOS and Android systems will be a little different.

Raise hand to activate display
The function raise hand to activate display is on by default. You can turn it off in the GloryFit.
You can also set the time for the bright screen to 5s/ 1 Os/ 15s on the smart watch.
Menu-Settings-Screen time
Do not disturb
You can set the start and end time of “Do not disturb” mode according
to your needs.

Note: When you turn on the “Do not disturb” mode, the “raise hand to activate display” and message notification function are unavailable.
Time system
Android: Device -Universal settings-Time system-Select 12-hour system or 24-hour system

IOS: Device-More settings24-Hours Time(on/off)
Unit
Android: Device -Universal settings-Unit-Select Metric system or British system

IOS: Profile-Setting-Unit
Temperature unit conversion: °C/°F
Step 1: Click the .. weather” icon in the upper left corner of the “Home” interface;
Step 2: Choose °C/°F which is in the upper right corner of the weather interface.

More

Step Accomplishment Reminder
You can set a target step number in the GloryFit.
When you reach this target, the smart watch will shake three times to remind you that you have completed the goal.
Firmware upgrade
If you are prompted to upgrade the software, please upgrade it in time.
Note: Please fully charge the watch before updating. If the battery is less than 3 0 °/o, the upgrade may fail.

Smart watch functions and settings

The home screen is the clock.

Swipe down to see the quick settings, such as Do Not Disturb, Bright, Flashlight, Find me, Theme, Settings.
Swipe up to see the notifications.
Swipe right to see the menu on your watch.
Swipe left to see the shortcut interfaces, such as Status, Heart rate, Sleep, Weather.
Press the button on the upper 1right to return.
Press the button on the lower right to training interface.

Main page function

Switch watch faces

Long press the main interface for 4-5 seconds to switch.
Or [Settings]-[Dial] to switch.
Note: You can also choose more faces in the Dash Board of GloryFit.

Status interface

Switch to the Status interface to check the steps, distances and calories.
The distances and calories are calculated based on the current walking steps, the height and weight set in the App individually.

Training interface

Switch to the Training interface, press the screen to enter the specific Training interface. Press the button on the upper right to pause, you can choose whether to continue or exit.

Heart interface

Switch to the Heart interface, click the screen to view the heart rate data.

Note:

The heart rate monitoring is enabled by default. If you don’t want this function, you can turn it off in the .. GloryFit 11 App.
If the heart rate monitoring function is on, the green light on the back of the watch will keep flashing.
If you find that the heart rate data is inaccurate, please pay attention to the following matters:
(1) Wear the watch with moderate tightness, and the sensor behind the watch should be close to the skin;
(2) Switch to the corresponding sports mode when exercising;
(3) If it is still inaccurate, please reboot the watch.

Blood oxygen interface

Switch to the Blood oxygen interface and measure your blood oxygen level at any time.

Note:

Heart rate monitoring will be suspended when monitoring blood oxygen, and vice versa.
In order to make the blood oxygen data more accurate, please ensure the following matters during monitoring:
(1) Ambient temperature is above 25°C;
(2) Keep your wrists flat on the table without moving.

Respiration rate interface

Switch to the Respiration rate interface and test your respiration rate at any time.

Breathing training interface

Switch to the Breathing training interface and carry out breathing training according to the instruction of the watch. You can adjust the training time and speed according to your needs.

Pressure interface

Switch to the Pressure interface and it only takes three minutes to monitor your pressure.

Music interface

You can play, pause or switch the tracks playing in your cell phone.

Sleeping interface

Switch to the Sleeping interface and check the sleep status. Sleep data is mainly based on heart rate and wrist movement range.
When you are asleep, the heart rate will decrease significantly.

Note:

Falling asleep between 6 a.m. and 6 p.m. is not recorded.
When you are lying in bed and playing with your phone for a long time, your heart rate and wrist movements are similar to the state of sleep. The watch may determine that you are asleep.

Weather interface

Switch to the Weather interface, you can view the weather and temperature.
Note: Weather function is only available after you turn on the “Location” of the mobile phone.

Message interface

In the Message interface, click the main screen to view the message, slide the screen to turn the pages. Press the button on the upper right to exit.

Note: Message reminder is just a function to remind you to receive a message. Its display interface will have character restrictions(80 characters for IOS and Android per message).

Female health interface

Through the App, you can record your personal menstrual cycle and predict the safety period, pregnancy and ovulation period, which can help women understand their physical condition in detail, so as to live a healthier life.

More

Stopwatch: Switch to the Stopwatch interface, click to enter the timing interface.
Timer: Switch to the Timer interface, and click to choose the time you want to count down. You can customize the time at the bottom of the page. When the time is up, the watch will vibrate.
Find me: Switch to the Find me interface and touch the icon, then the phone will ring.
Flashlight: Switch to the Flashlight interface, and press the screen to turn on the flashlight.

Settings

Dial: You can also press the main interface for 4-5 seconds to switch.

App Download: Scan the QR codes to install the App “GloryFit”.

Precautions

Please avoid strong impact, extreme heat and exposure to the watch.
Please do not disassemble, repair or transform the device on its own.
The use of the environment is O degrees -45 degrees, and it is forbidden to throw it into the fire so as not to cause an explosion.
Please wipe off the water with a soft cloth and then the watch can be used for the charging operation, otherwise it will cause corrosion of charging contact point and charging incident may occur.
Do not touch the chemical substances such as gasoline, clean solvent, propanol, alcohol or insect repellent.
Please do not use this product in high pressure and high magnetic environment.
If you have sensitive skin or tighten the wristband, you may feel discomfortable.
Please dry the sweat drips on the wrist in time. The strap has long contact with soap, sweat, allergies or pollution i ng red ients, which may cause skin allergy itching.
If it is often used, it is recommended to clean the wristband every week. Wipe with wet cloth and remove oil or dust with mild soap. It is not appropriate to wear a hot bath with a wristband. After swimming, please wipe the wristband in time so as to keep dry.

Basic parameter

Type

| 1.32 Inch Full Touch Smart Watch| Battery Type| Li-Polymer
---|---|---|---
Display Size| 1.32 Inch| Battery Model|

372026

Weight

DC 5.0V

Waterproof Level

Device, Manual, Charging cable

FAQ

Q: What should I do when my watch can’t be connected to the phone normally?

A: Please follow the instructions:
(1) Install the “GloryFit” App in Google Play or App store and allow all authorizations required by GloryFit.
(2) Make sure both of your watch and mobile phone Bluetooth are turned on. And it would be better that the distance between the mobile phone and the watch is less than 1m.
(3) If the watch is not connected to the mobile phone through the GloryFit App, but directly through the Bluetooth search, please delete the watch “S2” from the Bluetooth list of your mobile phone.
(4) If you want to connect to another new phone, please unbind the watch on the original phone through the GloryFit App first. (If the original phone is an iOS system, you also need to delete the watch S2 from the Bluetooth list of the phone).

Q: Why can’t the watch receive SMS / App information notification?

A: Please follow the instructions:
(1) Make sure that you have authorized the SMS/App notification for the Gloryfit App.
(2) Ensure that the watch is connected to the mobile phone through the GloryFit App.
(3) Make sure “Do not disturb” mode on the watch is turned off.
(4) Ensure that the SMS reminder and App reminder of the GloryFit App are turn on.
(5) Make sure that your GloryFit App is always running in the background.
Note: Some Android phones automatically close Apps running in the background every 10-15 minutes. If GloryFit App is stopped by the system, the watch will not receive any information notification.
You can keep the GloryFit App running in the background through “Setting” in your phone.
If you don’t know how to set it, you can search your mobile phone brand+ how to keep the App running in the background?” on Google.

Q: Is the sleep data accurate?

A: Sleep data is accurate.
Sleep data is mainly based on heart rate and wrist movement range. When you are asleep, the heart rate will decrease significantly. When you are lying in bed and playing with your phone for a long time, and your heart rate and wrist movements are similar to the state of sleep, the watch may determine that you are asleep. However, the third-generation algorithm of our watch has fixed this problem.
Note: Falling asleep between 6 a.m. and 6 p.m. is not recorded.

Q: How can I make my heart rate more accurate?

A: (1) Wearing the watch with moderate tightness, and the sensor behind the watch s.hould be close to the skin.
(2) Switch to the corresponding sports mode when exercising.

Q: Is the watch waterproof?

A: It supports 3ATM waterpro,of and dust-proof level (3ATM standard is 30 meters below water). Usually, you can wash your hands with the smart watch.
Note: But be sure not to enter the steam room with your watch. Such as sauna, hot spring, hot bath, etc.

For more information, please visit:

For any assitance, email us:

Made in China

Skylimit Service GmbH
Roedingsmarkt 20
20459 Hamburg

HUA TENG LIMITED
3 Glass Street, Hanley,
Stoke On Trent,ST1 2ET United Kingdom

Manufacture:
Name: Huizhou Xiansheng Technology Co., LTD
Address: 3rd Floor, Workshop No. 2, Yunhao High-tech Park, Yuhe Road, Sanhe Town, Huiyang Economic Development Zone, Huizhou, China