Hurley Marine H30+ Dinghy Davit System Owner’s Manual
- June 3, 2024
- Hurley Marine
Table of Contents
Hurley Marine H30+ Dinghy Davit System
WARNINGS
- WARNING – Extreme Caution should be used when operating this system . . . Failure to install, maintain, protect, and operate the system properly can cause malfunction resulting in possible serious or fatal injuries and/or property damage. Not to be operated by children.
- WARNING – Davit system is not intended to be used with any person(s) and/or possessions in the dinghy.
- WARNING – Do not attempt to operate system while boat is under power.
- WARNING – System should not be placed in an area where the prop, outdrive or any other mechanical part may come in contact.
- WARNING – Remove drain plug from tender when on davit.
- WARNING – A dinghy cover is recommended to keep water from entering the dinghy.
- WARNING – Do not drill holes in your davit or alter in any way.
- WARNING – Only use stainless steel hardware when mounting and use a backing plate when applicable.
- WARNING – Dinghy must be secured/tied down before transporting.
- WARNING – Winch and winch arm should be stowed when not in use
- WARNING – Contact the manufacturer of your swim platform to ensure that it is able to handle the added weight.
- WARNING – Regular inspection, adjustment, and maintaining your davit and other associated components is necessary to ensure proper operation.
- WARNING – Always clean the davit system with fresh water when it is used in a corrosive environment to maintain longevity. Annually use a Rust & Corrosion protectant on your stainless steel. “Fluid Film” is suggested.
- CAUTION: – It is suggested to off-set the davit, during installation, on the platform so that the stern of the dinghy is more supported due to weight of motor, etc.
- CAUTION – Weight limit: H3O+ = 725-pound safe working load. Do not exceed weight load limit. H3O+ XL = 1000 pound safe working load. Do not exceed the weight load limit.
Your Hurley H3O+ Dinghy Davit system is made of Marine Grade High-Density Polyethylene and stainless steel components and hardware. All of these components are used for strength, and longevity and to reduce friction during retrieval and launching.
Planning the installation: A mounting template has been included with
these instructions and should be used to properly a-line, drill, and install
the mounting plates. You may want to offset the davit on the platform so that
the stern of the dinghy is more supported due to the weight of the motor, etc.
Of course, this depends on many factors, including, but not limited to, the
beam of your boat, the length of your dinghy, and any obstructions. Note: The
davit must be able to pivot over the edge of your platform.
Mounting the Plates: It is suggested to use four Stainless Steel 5/16”
Button Head Socket Cap Screws (not included). Using the Mount Template center
punch each hole. Start with a small drill bit and increase bit size to 5/16”.
It is good practice to use tape on the surface to be drilled then drill the
hole through the tape, this will avoid scratching/chipping of the surrounding
surface. Measure twice, drill once! Generously apply 3M 5200 sealant to seal
drilled holes and the bottom of the mounting plates. Secure fasteners using
nylon nuts, fender washers or backing plates, when applicable, and nyloc nuts
when thru bolting. Do not apply more than 8-10 foot-pound (ft-lbf) of torque.
Electric Winch Operation: Please see Electric Winch Instructions.
Tie-downs must be used when underway, we recommend our 3-Point or 4-Point
Tie-Down system for best results.
There is a third mounting pin included with your H3O+ Davit. It can be used as
a replacement pin for mounting or can be used to stop the rotation of the
davit, only if there is no tender on the davit system, by inserting it in the
hole of the plate. This should only be used when transporting the davit with
no tender atop as so it doesn’t rotate and drag in the water. Adjust the inner
bunks with the hull of the tender as so the both outer and inner linear bunks
are supporting the hull. In some cases, the inner bunks may not work due to
hull configurations.
Inspection and tightening of screws, nuts and bolts should be performed weekly. Always clean the davit system with fresh water when it is used in a corrosive environment. Annually use a Rust & Corrosion protectant on your stainless steel. “Fluid Film” is suggested.
LIMITED WARRANTY AND LIMITATION OF LIABILITY
All new products manufactured under Hurley Marine, Inc., are warranted to be free from defects in material and workmanship under normal and proper use for a period of (2) two years, electric & manual winches, and electrical components 90 days, from the date of shipment from Hurley Marine, Inc. No claim for breach of the warranty will be allowed unless the material or workmanship is found defective within the warranty period, properly documented by the buyer and Hurley Marine, Inc. is notified in writing within 10 days from failure. This warranty shall not apply to products that have been disassembled, altered, or utilized in a manner not approved by Hurley Marine, Inc. or subjected to normal wear and tear, abuse, misuse, improper maintenance, negligence or accident. THE CUSTOMER AGREES THAT THE USE OF THE PRODUCT/SERVICE IS ENTIRELY AT THE CUSTOMER’S OWN RISK. THE FOREGOING WARRANTIES ARE EXCLUSIVE AND ARE ACCEPTED BY THE BUYER IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Buyer’s sole remedy in the event of a breach of the forgoing warranties is the repair or replacement of the affected product by Hurley Marine, Inc., upon the return of the product transportation charges prepaid to Hurley Marine, Inc., and after a charge to the buyer for the use of the product prior to its return.
BUYER AGREES THAT IN NO EVENT WILL HURLEY MARINE, INC’S LIABILITY FOR ALL LOSSES FROM ANY CAUSE, WHETHER BASED ON CONTRACT, NEGLIGENCE, STRICT LIABILITY, OTHER TORT OR OTHERWISE, EXCEED BUYER’S NET PURCHASE PRICE, NOR WILL HURLEY MARINE, INC, BE LIABLE FOR ANY SPECIAL, INCIDENTAL CONSEQUENTIAL OR EXEMPLARY DAMAGES. Under no circumstances is Hurley Marine, Inc. responsible for reimbursement of expenses related to vessel haul-outs, technician or yard personnel, travel expenses, yacht storage, labor performed during removal and/or replacement of fixture(s), or shipping costs for replacement parts and/or repairs. These are assumed liabilities of the customer and part of the terms of sale between Hurley Marine, Inc. and its customer. The foregoing warranties will continue in effect for so long as the product is serviced and maintained in accordance with Hurley Marine, Inc. instructions and with genuine Hurley Marine, Inc. manufactured replacement parts. These warranties may not be altered or amended except by a written instrument signed by buyer and a duly authorized officer of Hurley Marine, Inc. For warranty or service assistance contact your Hurley Marine, Inc. dealer.
TERMS OF SALE / SHIPPING
RETURN POLICY: If you are dissatisfied with your purchase, contact us
within 30 days from the date of product purchase. Products returned within 30
days of their receipt, unopened in their original packaging and otherwise in
new condition will automatically be exchanged or refunded. A minimum fee of
25% of the price of the product will be charged for inspection, repacking, and
restocking for items not returned in their original condition. Other fees may
apply depending upon the condition of the item. Products are not returnable
after 30 days.
EXCHANGE / REFUND PROCEDURE:
- All returns must have a copy of a paid invoice, contact information, and a brief description of the reason accompanied with the return.
- Properly repack the product in the original packaging and place it inside a box suitable for shipping with all the original enclosures, parts, and accessories.
- Return it with the original receipt and postage pre-paid (we do not accept C.O.D.), add appropriate insurance.
- Shipping and packing fees are non-refundable.
Non-Returnable items: Inflatable boats, installed/mounted items, damaged
goods, clearance/discount items, used and/or display items, electrical goods,
light bulbs, and special ordered items are not returnable, unless defective,
and then for repair/replacement only. If the product is defective you must
call Hurley Marine, Inc. within 10 days of receipt of the product.
DAMAGES GOODS: We thoroughly inspect all items prior to shipment. We
suggest that you also thoroughly inspect the item(s) before accepting
delivery. If damage is apparent, refuse delivery or if your parcel is left
without a signature and damage is found contact the carrier immediately. Do
not discard the box or any packaging materials. Most claims must be filed with
the carrier within 10 days of receipt of delivery. Although we take special
care to ensure the safe arrival of your merchandise, our responsibility for
damage ends when the carrier accepts the shipment.
Hurley Marine, Inc. • 2717 N Lincoln Road • Escanaba, MI 49829 USA 906. 553.6249 • info@hurleymarine.com • hurleymarine.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>