MIZAMA MZD3 Tire Pressure Monitor System Instruction Manual
- June 15, 2024
- MIZAMA
Table of Contents
MIZAMA MZD3 Tire Pressure Monitor System Instruction Manual
Caution: Must turn on the monitor first and then install the sensors. Long press “+” &”-” buttons for 3 seconds to turn on the monitor.
Monitor components
| Icon | Description |
|---|---|
| Tire | |
| Sensor low Battery | |
| Monitor Battery | |
| Alert | |
| Solar charging |
Selectable units: Pressure unit: BAR or PSI Temperature unit: °C or °F
Kit Contents
The monitor and ACC
Monitor ( 1 pc)
USB Cable (1 pc)
The sensor and ACC
Sensor (4pcs)
Hex Wrench (1pc)
Hex Nut (4pcs)
Spare O-Ring (4pcs)
Monitor installation
Attach monitor to car windshield by its sticker as the image shown below,
stick at where is easy to view. Charge the monitor display by a USB cable
connecting to car cigarette lighter charger (charge for 2.5 hours or more for
the first time).
Notice:
- Install the monitor display inside driver cabin where it does not block driver’s view and not affect regular driving.
- Firmly fix the monitor display to prevent falling off during driving.
- Be sure of safety while checking tire data on monitor during driving.
- With correct installation this TPMS system issues alert when abnormal situation detected, driver does not have to check the monitor frequently and should focus on safe driving.
Sensor Installation
Note: Before installing the sensor, make sure that the tire pressure is the required air pressure or the standard air pressure.
-
Screw in the nut. (Only screw in the nut if you need anti-theft installation.)
-
Screw the sensor onto the valve.
-
Tighten the nut with the provided spanner.
Sensor battery replacement
-
With the provided tools to screw sensor counterclockwise to open its cover.
-
Fix in the new battery (positive +side facing up).
-
Check the O-ring robber is ok, clockwise screw back the sensor cover by hex wrench.
Default setting
Factory default setting
Reference pressure
When the sensor is installed on the tire, the current pressure will become
the reference pressure
Pressure Unit
| PSI
Temperature Alert
|
°F
High temperature alert|
158°F
Unit setting
In standby mode, long press + button for 3 seconds to change pressure unit. In
standby mode, long press – button for 3 seconds to change temperature unit.
Monitor display change
In standby mode, press +/- button to spare tire pressure and temperature.
Automatically setting reference pressure
There is no need to set high/low pressure alert. When sensor is installed,
the current tire pressure is the reference pressure. The high pressure alert
is 25% higher than the reference pressure. The low pressure alert is lower 15%
reference pressure.
Recover default settings
Turn off monitor, long press +&- buttons to turn on the monitor. Long
press SET button until a Bl in 3 seconds. Recover default settings has been
done.
Alert status
Alert
|
Alert status
---|---
High Pressure Alert
| +25% PSI
Low Pressure Alert
| -15% PSI
High Temperature Alert
| 158 °F
Fast Leakage Alert
|
Sensor Low Battery Alert
|
Sense Lost Signal Alert
|
Specification
Monitor
Operation temperature
| -20°C— 80°C
Storage terneplate re
| -30°C – 85°C
Input voltage
| DC 5V
Frequency
| 433.92MHz
Dimension (Lx Wx H)
| 93×57 x28 mm
Weight|
70g
Sensors
Detecting pressure range| 0-87PSI (0-6BAR )
Operation temperature| -40°C-80°CI
Storage temperature| -40°C-85°C
Frequency| 433.92MHz
Transmission power| <10dBm
Pressure accuracy| ±1.5PSI (±0.1BAR )
Temperature accuracy| ±3°C
Dimension| 21(diajx16(H)mm
Weight| lOg
FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following meas ures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body:
Use only the supplied antenna.