MINKA LAVERY 2431-84 Winsley 5.375 Inch 1-Light Coal and Stained Brass Vanity Light Instruction Manual

MINKA LAVERY 2431-84 Winsley 5.375 Inch 1-Light Coal and Stained Brass

Vanity Light

Product Information

The product is a ceiling fixture with item number 2431-84/878. It comes with a circular strap, ground screw, mounting screw, finials, metal ring, glass shade, and socket cup. The fixture requires one medium base (E26) bulb up to 60 watts or CFL or LED equivalent (not included). The installation manual warns to not exceed the maximum wattage rating.

Usage Instructions

1. Turn off power at the fuse box or circuit breaker.
2. Remove the old fixture and its mounting hardware.
3. Unpack the new fixture and lay out all parts in a clean area.
4. Thread mounting screws into pre-drilled holes in the circular strap spaced the same distance apart as holes in the back plate. Tighten with nuts. Adjust the length of mounting screws if necessary.
5. Attach the circular strap to the junction box using junction box screws. The side of the circular strap marked GND must face out. Connect the electrical wires as shown in Fig.2, making sure that all wire connectors are secured. If your junction box has a ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the circular strap using the green screw provided. Tuck wire connectors neatly into the junction box.
6. Place the back plate onto mounting screws and secure it with finials. Unscrew the metal ring and place the glass shade onto the socket cup. Secure glass shade with metal ring.
7. Install one medium base (E26) bulb up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. Do not exceed the maximum wattage rating.
8. Turn the power back on at the junction box and test the fixture.

Note:
The illustration in the manual is for installation purposes only and may or may not be identical to the fixture purchased.

WARNING!
SHUT THE POWER OFF AT THE FUSE OR CIRCUIT BREAKER.

INSTALLATION

MOUNTING THE FIXTURE (Fig.1)

1. Shut off power at the fuse box or circuit breaker and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts on a clean area. Take care not to lose any small parts necessary for installation.

3. Thread mounting screws (B) into pre-drilled holes in circular strap (G) spaced the same distance apart as holes in back plate and tighten with nuts (E). The length of mounting screws (B) may be adjusted if necessary.

4. Attach circular strap (G) to junction box (not included) using junction box screws (D). The side of circular strap marked “GND” must face out.
   CONNECTING THE WIRES (Fig.2)

5. Connect the electrical wires as shown in Fig.2, making sure that all wire connectors (C) are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the circular strap (G) using the green screw provided.

6. Tuck wire connectors neatly into the junction box.
   FINISHING THE INSTALLATION (Fig.1)

7. Place the back plate onto mounting screws (B) and secure it with finials (A).

8. Unscrew metal ring (F) and place glass shade (I) onto socket cup (H). Secure glass shade (I) with a metal ring (F).

9. Install (1) one medium base (E26) bulb up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

Your installation is now complete. Return power to the junction box and test the fixture.

Note:
The illustration (Fig.1) in this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>