MINKA LAVERY 2164-66A Pendant Instruction Manual

MINKA LAVERY 2164-66A Pendant

Product Information

The product is Item#2164-66A, a new fixture that was manufactured on July 27, 2021. The fixture comes with a mounting plate (A), ground screw, mounting screws (B), canopy (D), four rods (F1, F2, F3, G), all thread (H), and candelabra base bulbs (I) which are not included and must be purchased separately. The fixture can accommodate up to four candelabra base bulbs or CFL/LED equivalents, not exceeding 60 watts each. The installation process involves shutting off the power supply, removing the old fixture, and installing the new fixture using the provided mounting hardware and wiring.

Product Usage Instructions

1. Before starting the installation process, shut off the power at the fuse box or circuit breaker box.

2. Remove the old fixture and its mounting hardware.

3. Unpack the new fixture and lay out all parts in a clean area.

4. Secure rod (G) onto all thread (H) on the fixture body.

5. Determine the desired hanging height and thread rods (F1, F2, F3) to all thread on rod (G).

6. Attach canopy (D) by screwing onto rod (F1). Carefully pass the
   wires through each rod during assembly. Remove all thread if installing with one 6 rods only.

7. Attach the mounting plate (A) to the junction box with mounting screws (B). The side of the mounting plate (A) with GND marked on it and two convex points must face out.

8. Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.

9. Place canopy (D) over the mounting plate (A) and secure with screws (E).

10. Install four candelabra base bulbs (I) up to 60 watts each or CFL/LED equivalent (not included) in accordance with the fixture  specification. Do not exceed the maximum wattage rating

11. Once installation is complete, turn on the power supply and test the fixture.

INSTALLATION INSTRUCTIONS

WAR N I N G ! S H U T P O WE R O F F AT F U S E O R C I R C U I T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARATION (Fig.1)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.

3. Secure rod (G) onto all thread (H) on the fixture body.

4. Determine the desired hanging height and thread rods (F1, F2 and F3) to the all thread on rod (G). Attach canopy (D) by screwing onto rod (F1). Carefully pass the wires through each rod during assembly. Note: Remove the all thread, if installing with one 6” rod only.

5. Attach the mounting plate (A) to the junction box (not included) with mounting screws (B) (Size: #8-32N*L0.5”). The side of the mounting plate (A) with “GND” marked on it and two convex points must face out.
   COMPLETING THE INSTALLATION (Fig. 1)

6. Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.

7. Tuck wire connectors neatly into the junction box.
   COMPLETING THE INSTALLATION (Fig. 1)

8. Place canopy (D) over mounting plate (A) and secure with screws (E).

9. Install (4) four candelabra base bulbs (I) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

Your installation is now complete. Return power to the junction box and test the fixture. Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Fig. 1

Set#A-021-118DH

• Mounting plate
• Ground screw
• Mounting screw*2

*Rod# W30-1-66A1(F1)**

• W30-1-66A *2(F2)
• W30-H-66A *1(F3)

Fig. 2

• FIXTURE
• WIRES
• Black or
• Smoothm

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>