MONOFLO 50870 Heat Mats Instructions
- October 27, 2023
- MONOFLO
Table of Contents
MONOFLO 50870 Heat Mats
Instruction manual for Monofl o heating plates
- Electric connection: 230V / 50Hz
- Electric consumption: Printed on each heat mat, on average 1,15 Watt per dm²
- Protection class: IPX7
- Material: PVC
- Sensor of the heating plate: resistance 4.7 k/Ohm at 20° C
- Temperature: Adjustable with our controller No. 50804, 25° C – 40° C
- Temperature of surroundings: 5° C – 40° C max.
- Capacity: 80 kg/m²
- Installation: Only through an electrician
- FI- switch: Installation of this switch is mandatory
- Manufacturer: Monofl o Produktions GmbH & Co KG
- Use: Warming plate for animals, pigs
- Connection method Z: Electric cable cannot be replaced. When the cable is damaged, the heating plate must be replaced.
Installation
The heating plates can only be used in combination with our Monofl o controller No. 50804. The heating plates must be protected from sharp objects, they may not be bent or drilled. They must be securely fastened through the existing holes onto a stable and even surface. Therefore, three special brackets will be included in the delivery. Before you install the heating plate, please open with a pliers the metal clips that hold the black adaptor. Then pull the adaptor off from the stainless steel protection pipe. Afterwards mount the heating plate to the fl oor, so it cannot dislodge. The ½” swivel nut of the protection pipe must be screwed on to the ½” bushing. Hereby please make sure that the rubber washer is pressed fi rmly into the ½” bushing.
The ½” nut should NOT be tightened with full force!
The cable protection should be fi xed with at least 2 clamps (17 mm) against
the wall or panels, separating the pens.Finally, the black adaptor at the top
of the cable protection must again be pushed over the pipe on locked with the
2 metal clips. All connections must be re-checked to make sure no moisture can
come into the heating plate. The electric installation must be done as shown
on the plan, which is found inside of the controller. The hook-up must be done
by an electrician. Attention: When using heating plates without controller you
may not install any additional sources of heat. When using the heating plates
in combination with our controller you may use additional heat sources.
Important though is that the same heat sources are used on the mother plate
(the one with the sensor) as on the followings heating plates, which have no
sensor.
The heating plates cannot be covered with blankets, straw or any other
materials. A heat blockage must be avoided. Caution risk of fire!
Damaged heating plates or cables cannot be installed. The power cord must be
NOT accessible to the animals. IMPORTANT! During the cleaning of the heating
plates the complete electric system must be turned off. Due to manufacturing
tolerances on the heating plates, the spot-measurement of the temperature can
vary + / – 10 ° C. The heating plates‘ surface warms up to 40° C if th ambient
tempertaure is about 22° C. These instructions must be translated by our
dealers into their respective language.
Instructions for controller No. 50804
- Electric connection: 230V / 50Hz
- Max. outlet: 2.200 W (including mother heating plate) IP45, weight 480 gr.
- Temperature: Adjustable 25 ° C – 40° C
- Installation: Only through an electrician
- FI-switch: Installation of this switch is mandatory
- Manufacturer: Monoflo Produktions GmbH & Co KG
- Connection method: X, no special electric connection required
Installation
The controller must be mounted on a solid and not flammable surface. Depending on the electric cable routing the respective holes must be drilled into the housing beforehand into the marked places. The electric installation must be done as shown on the plan, which is found inside of the controller. The hook- up must be done by an electrician. As power supply connection you must install a NYM-J 3×1, 5 cable! The controller can be adjusted starting at 25°C in steps of 1.6°C by pushing the ‘+’ button. Once your each 40° C you can push again to get back to Zero. Damaged controllers may not be used. These instructions must be translated by our dealers into their respective language.
Instruction
MONOFLO
Produktions GmbH & Co. KG Lise-Meitner-Straße 16 64646 Heppenheim Germany Fon
+49 62 52 99 08 – 0
- Fax +49 62 52 99 08 – 28
- www.monoflo.de
- info@monoflo.de