MINKA LAVERY 2898-691 3 Light Chandelier Instruction Manual

MINKA LAVERY 2898-691 3 Light Chandelier

Product Information and Usage Instructions

The product being installed is Item#2898-691, which is a fixture used for lighting. The installation instructions were last updated on August 18th, 2021.

Installation Instructions

Before beginning the installation process, it is important to shut off power at the fuse box or circuit breaker box. The old fixture including the mounting hardware should be removed. The new fixture should be carefully unpacked, and all the parts laid out in a clean area. The desired hanging height should be determined, and the thread rods (F1, F2 and F3) should be attached to all thread (E) on top of the fixture body. The canopy (C) should be attached by threading onto rod (F1). Wires should be carefully fed through each rod as you assemble. The mounting plate (A) should be attached to the junction box with mounting screws (B). The side of the mounting plate (A) marked GND and two convex points must face out.

Connecting the Wires

The electrical wires should be connected as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.

Finishing the Installation

The canopy (C) should be slid over the mounting plate (A) and secured with screws (D). Three candelabra base bulbs (H) up to 60 watts each or CFL or LED equivalent (not included) should be installed in accordance with the fixture specification. Glass shades (I) should be screwed onto socket cups (G). After the installation is complete, power should be returned to the junction box, and the fixture should be tested.

INSTALLATION INSTRUCTIONS

Item#2898-691 (New. 2021/08/18)
READ AND SAVE THESE INSTRUCTIONS

WARNING! SHUT POWER OF FATFUSE OR CIRCUIT BREAKER .

MOUNTING THE FIXTURE (Fig.1)

1. 1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.

3. Determine the desired hanging height and thread rods (F1, F2 and F3) to all thread (E) on top of fixture body. Attach canopy (C) by threading onto rod (F1). Carefully feed wires through each rod as you assemble. Note: Remove all thread, if installing with one 6” rod only.

4. Attach mounting plate (A) to junction box (Not included) with mounting screws (B) (Size: #8-32N*L0.5”). The side of the mounting plate (A) marked “GND” and two convex points must face out.

5. CONNECTING THE WIRES (Fig. 2)

6. Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured.

7. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.

8. Tuck wire connectors neatly into the junction box.
   FINISHING THE INSTALLATION (Fig.1)

9. Slide canopy (C) over mounting plate (A) and secure with screws (D).

10. Install (3) three candelabra base bulbs (H) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. — DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

11. Screw glass shades (I) onto socket cups (G).

Your installation is now complete. Return power to the junction box and test the fixture.

Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>