MINKA LAVERY 2863-66A Sheer Elegance 4-Light Coal Drum Pendant Light Instruction Manual

MINKA LAVERY 2863-66A Sheer Elegance 4-Light Coal Drum Pendant Light

Product Information

The product is a hanging light fixture with a model number of 2863-66A. It comes with a mounting plate, canopy, candle covers, and three threaded rods (F1, F2, and F3). The fixture can accommodate four candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included).

Product Usage Instructions

1. Turn off power at the fuse box or circuit breaker box andremove the old fixture including the mounting hardware.
2. Unpack the new fixture and lay out all the parts in a clean area.
3. Determine the desired hanging height and thread rods (F1, F2, and F3) to all thread (I) on fixture body. Screw loop (H1) to rod (F1). Pass the wires carefully through each rod as you assemble.
4. Attach quick link (G) to loop (H1) and loop (H2) on the canopy (D). Carefully feed the wire through loop (H1), quick link (G), and loop (H2).
5. Attach mounting plate (A) to the junction box with mounting screws (B). The side of the mounting plate (A) with GND marked on it and two convex points must face out.
6. Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.
7. Tuck wire connectors neatly into the junction box.
8. Place canopy (D) over mounting plate (A) and secure with screws (E).
9. Place candle covers (K) over sockets (L).
10. Install (4) four candelabra base bulbs (M) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
11. Turn on power at the fuse box or circuit breaker box and test the fixture..

INSTALLATION INSTRUCTIONS

Item# 2863-66A (New. 2022/05/26)

READ AND SAVE THESE INSTRUCTIONS

WARNING! SHUT POWER OF FATFUSE ORCIRCUIT BREAKER .

AVERTISSEMENT! COUPERLE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARATION (Fig. 1 &Fig. 3) 

1. Shut of power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.

3. Determine the desired hanging height and thread rods (F1, F2 and F3) to all thread (I) on fixture body. Screw loop (H1) to rod (F1). Pass the wires carefully through each rod as you assemble.

4. Attach quick link (G) to loop (H1) and loop (H2) on the canopy (D). Carefully feed the wire through loop (H1), quick link (G), and loop (H2).

5. Attach mounting plate (A) to the junction box, not included, with mounting screws (B) ( Size: #8-32N*L0.5”). The side of the mounting plate (A) with “GND” marked on it and two convex points must face out.
   CONNECTING THE WIRES (Fig. 2)

6. Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.

7. Tuck wire connectors neatly into the junction box. COMPLETING THE INSTALLATION (Fig. 1)

8. Place canopy (D) over mounting plate (A) and secure with screws (E).

9. Place candle covers (K) over sockets (L).

10. Install (4) four candelabra base bulbs (M) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

Your installation is now complete. Return power to the junction box and test the fixture.

Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

• Hardware Bag:
  • A. Mounting Plate *1
  • B. Mounting Screw*2.
  • D. Canopy *1
  • E. Screw*2
  • G. Quick Link*1
  • H. Loop*2
• Hardware Bag:
  • F1. ROD 12″*1
  • F2. ROD 12″*2
  • F3. ROD 6″*1

LA-3535E

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>