TRUE FINE TD10032FL Flush Mount Lighting Instruction Manual

: October 30, 2023
: TRUE FINE

Table of Contents

TRUE FINE TD10032FL Flush Mount Lighting
Product Information:
Product Usage Instructions:
Overview
Assembly Instruction
Wiring Instruction
Product Specifications
Cleaning
Safety Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TRUE FINE TD10032FL Flush Mount Lighting

TRUE FINE TD10032FL Flush Mount Lighting product

Product Information:

The Flush Mount Lighting is a type of light fixture that is designed to be installed directly onto the ceiling. It comes with a fixture body (A), a lamp shade (B), a finial (C), a canopy (D), and a mounting strap (E). The product also includes a green grounding screw, wire connectors, and screws for installation. The product is designed to be connected to an outlet box and comes with wiring instructions.

Product Usage Instructions:

Before installing the Flush Mount Lighting, switch off the electricity supply and allow it to cool for 10 minutes.
Start by installing the green grounding screw into the hole with two raised dimples on the mounting bar. If the ground wire from the fixture is supplied, wrap it around the green grounding screw and connect it to the ground wire from the outlet box using a wire connector. If the ground wire from the fixture is not supplied, wrap the ground wire from the outlet box around the green grounding screw and tighten it. NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
Identify the color of the wires on your fixture and group them according to [GROUP A] or [GROUP B]. Connect the wires according to the directions in the wiring instruction, making sure no bare wires can be seen outside wire connectors.
Pass the wires through Lamp shade (B) and Canopy (D), then screw Canopy (D) to Fixture body (A).
Fix Mounting strap (E) to outlet box with Screw (F).
Connect the wires according to the picture in the wiring instruction.
Pass Canopy (D) through the screw and fix it with Finial (C).
To clean the Flush Mount Lighting, wipe the fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.

If you have any questions or concerns about the installation or usage of the product, please contact the manufacturer’s customer service team at service @24h-reply.com.

Overview

Assembly Instruction

Pass the wires through Lamp shade (B) and Canopy (D), then screw Canopy (D) to Fixture body (A).
Fix Mounting strap (E) to outlet box with Screw (F).
Connect the wires according to the picture above.
(Please refer to the wiring instruction for details )
Pass Canopy (D) through the screw and fix it with Finial (C).

Wiring Instruction

Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector(not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:

[GROUP A]:
Connect to Black House Wire

| [GROUP B]:
Connect to White House Wire
---|---
BLACK| WHITE
PARALLEL WIRE (round & smooth)| PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT TRACER| BROWN, GOLD OR BLACK WITH TRACER
3. Take your fixture wire(s) from [Group A] and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors. 4. Fit a wire connector over the wires and screw the connector clockwise until you feel firmness. 5. Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection. 6. Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

Product Specifications

Input voltage 120V
Rated power 60W MAX × 2
Lamp socket E26

Product Packaging

Fixture body × 1
Lamp shade × 1
Mounting strap × 1 & Canopy × 1
Screw × 2 & Wire nut × 3
Lamp instruction × 1

Cleaning

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.