SYLVANIA 4210519 4 Inch LED Retrofit Downlight Instruction Manual

SYLVANIA 4210519 4 Inch LED Retrofit Downlight

Product Information

Specifications

• Model: LEDRT4R500ST9SC3WHTW
• Color Temperature Options: 2700K, 3000K, 3500K, 4000K, 5000K
• Lighting Distribution:
  • 3 FT. – 23 foot candles
  • 5 FT. – 8 foot candles
  • 8.8 FT. – 15 foot candles
  • 15 FT. – 8 foot candles
  • 24 FT. – 3.3 foot candles
  • 44 FT. – 15 foot candles

Product Usage Instructions

1. Choose the desired color temperature by pressing the push button on the device.
2. Ensure the device is installed and used in accordance with the provided instructions to avoid interference with radio communications.
3. Maintain a human proximity of at least 20cm (8 inches) to the antenna during normal operation to comply with FCC radiation exposure limits.
4. If interference with radio or television reception occurs, consider the following measures:
   • Reorient or relocate the receiving antenna.
   • Increase the separation between the equipment and receiver.
   • Connect the equipment into an outlet on a different circuit from that of the receiver.
   • Consult the dealer or a radio/TV technician for assistance.

FAQ

• Q: How do I change the color temperature on the device?
  • A: You can change the color temperature by pressing the push button on the device to cycle through the available options.
• Q: What should I do if I experience interference with radio or TV reception?
  • A: If interference occurs, try reorienting or relocating the receiving antenna, increasing the separation between equipment and receiver, connecting to a different outlet, or seeking assistance from a professional technician.

LEDRT4R500ST9SC3WHTW

For warranty coverage, please register at www.ledvanceUS.com

WARNING

Please Read All Instructions Before Attempting Installation

• Turn off electricity at circuit breaker box (or main fuse box) before beginning installation by removing fuse (or switching off circuit breaker).
• Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury or death from electric shock.
• All electrical connections must agree with local codes, ordinances or the National Electric Code (NEC). Contact your municipal building department to learn about your local codes, permits and/or inspections.
• Risk of fire – most dwellings built before 1985 have supply wire rated for 140° F/60°C. Consult a qualified electrician before installation.
• Do not connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use a fixture in a two-wire system that is not grounded. If you are not sure your lighting system has a grounding means, do not attempt to install this fixture. Contact a qualified, licensed electrician for information with regards to proper grounding methods as required by the local electrical code in your area.
• If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type and electrical rating required.

Preparation

Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with package contents list and diagram on previous page. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts.

TOOLS REQUIRED

TOOLS REQUIRED (not supplied)

CONTENT

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, Human proximity to the antenna shall not be less than 20cm(8 inches)during normal operation. That changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Supplier’s Declaration of Conformity: 47 CFR § 2.1077 Compliance Information

• Responsible Party: LEDVANCE LLC
• 1100 Tyrone Pike Versailles,KY 40383,
• USA 1-800-544-4828
• Unique Identifer: 63868
• CAN ICES-005 (B)

Installation

1. Turn Off the Power.
   Before beginning the installation, make sure all power is off at the breaker box. Remove the disuse existing bulb if necessary and remove the existing trim.

2. Installing E26 base adapter
   Twist the E26 base adapter (AA) into the lamp holder.

3. Connect the connector
   Connect the retrofit (A) connector with E26 base adapter (AA).

Operating Instructions

Connecting Lamps together

• After installation is done, turn the power ON.
• The product will start blinking slowly for about 30 seconds and pair together automatically.

Note: If the product doesn’t enter pairing mode, simply turn ON/OFF the wall switch of the group of products you want to pair together three times.

Changing Color Temperature:

• Select the desired color temperature by pressing the push button on one of the units.
• All units will automatically follow and adjust to the same color temperature.

Adding Products to a Group:

• To add a unit to a group, press and hold the CCT button for 3 seconds on the unit you want to add to the group, and then press the CCT button on one unit from the group.
• Unpairing Fixtures from Remote or Groups:

Using the Wall Switch:

• Turn the wall switch ON/OFF three times at a normal speed.
• All units connected to the wall switch will pulse three times to indicate they are unpaired.

For Individual Fixtures:

• Press and hold the fixture switch for 6 seconds.
• The fixtures will pulse three times to indicate they are ready for the next command.

Lighting Distribution

CARE AND MAINTENANCE

To clean, turn off and wipe with a damp, non-abrasive cloth.

TROUBLESHOOTING

1. The light does not come on at all:
   • a Make sure the wall switch and circuit breaker are on.
   • b)Make sure the wiring is correct.
2. The fuse blows or circuit trips when the light is turned on.
   • a)Check for crossed wires, and ensure wiring is correct.

If unable to fix any of the above issues, please consult a certified electrician.

LIMITED WARRANTY

5 YEAR LIMITED WARRANTY: LEDVANCE warrants the Product to be free from defects in material and workmanship from date of purchase for the specified warranty period when used as directed. Failure to comply with Product warnings and instructions shall void the warranty. This warranty does not cover Product subject to accident, neglect, abuse, misuse, or acts of God, If Product fails to operate according to the warranty, return Product to place of purchase with proof of purchase date and LEDVANCE will replace with the same or similar Product free. LABOR IS NOT INCLUDED. LEDVANCE reserves the sole right to examine and determine whether the Product is defective. For additional information, contact 1-800 LIGHT- BULB(1-800-544- 4828);Email: lightbulb@ledvance.com.THIS IS THE EXCLUSIVE REMEDY AVAILABLE. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS EXPRESSLY EXCLUDED. SOME STATES AND EXCLUSION JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTY OF MERCHANTABILITY OR FITNESS OF USE, WHICH ARE HEREBY EXCLUDED. IF UNDER APPLICABLE STATE LAW IMPLIED WARRANTIES MAY NOT VALIDLY BE DISCLAIMED OR EXCLUDED, THE DURATION IS LIMITED TO THE SPECIFIED WARRANTY PERIOD.

• www.ledvanceUS.com
• www.ledvanceUS.com (US & Canada)
• SYLVANIA is a registered trademark.

References

• LEDVANCE US and Canada | SYLVANIA General Lighting | Home Page

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>