Eventide V10 Tricera Chorus User Guide

Eventide V10 Tricera Chorus

Presets – 5 On Board, 127 Via MIDI

The currently loaded Preset is indicated on the Preset LED Ladder. When a Preset is modified the Preset LED blinks once.

Load Presets
To select and load a Preset using Footswitches:

1.  SWIRL Footswitch selects Preset 1 to 5. Preset 1 (top LED) to Preset 5 (bottom LED) blinks.
2.  ACTIVE Footswitch loads the Preset. LED stops blinking.
   NOTE:
   To select Preset, SWIRL Footswitch must be in Preset mode. If SWIRL LED is lit, press and hold SWIRL Footswitch.

Catch Up Knob Function

When a Preset is loaded or when toggling between Parameters using , Knob positions will not align with their current Parameter values. As a result, turning a knob will likely cause an abrupt change in the sound. With Catch Up ON, the sound does not change until the Knob is moved to the position corresponding to the current value. The LED Ladder indicates whether the knob must be turned CCW (top LED blinks) or CW (bottom LED blinks). The LED flashes more rapidly as the knob approaches the value set by the Preset. All five LEDs blink once when the knob matches the stored Parameter value.
NOTE:
To enable/disable Catch Up Knob Function, power up in System Setup mode and press SWIRL Footswitch to toggle ON/OFF.

Save Presets
To save one of the 5 Presets using the Buttons:

1. Press & hold SWIRL Button  Blinking Ladder and Button LEDs let you know you have entered Save Mode.
2. SWIRL Button selects Preset 1 to Preset 5.
3. ACTIVE Button saves Preset LEDs stop blinking to let you know the Preset is saved.
   NOTE:
   SWIRL status is saved with the preset. Save Mode times out after a few seconds. Pressing either Footswitch exits Save Mode.

SWIRL Footswitch Functionality

Press & Hold the SWIRL Footswitch to toggle between SWIRL mode and Preset Select mode. In SWIRL mode, press the SWIRL Footswitch to turn ON/OFF SWIRL.

LED GREEN

| ****

SWIRL ON

| Swirl adds another dimension to TriceraChorus’ sound via stereo phase shifters after the Detune section to create throbbing and swooshing effects.

The amount of Swirl depends on the greater level of either Chorus Mix or Detune Mix and follows the Env Mix control. Swirl speed is adjusted by Rate and follows the ENV Rate control. Use faster rates to achieve deeper Swirl effects.

Device Manager Software
Available from Eventide’s website for Mac & PC

•  Update Pedal Firmware
•  Restore Factory Settings
•  Import/Export Presets
•  Backup/Restore entire device to a file
•  Edit System Settings
• View, edit, and organize Presets

Download: eventideaudio.com/edm Restore Factory Settings: Boot pressing ACTIVE Footswitch & ACTIVE Button Software Update: Boot pressing SWIRL Button & SWIRL Footswitch TriceraChorus Quick Reference Guide for Firmware v1.0+| Eventide Part# 141348 Rev A Eventide is a registered trademark of Eventide Inc. © 2021 Eventide Inc.

TriceraChorus Quick Reference Guide

Knob Functions – Secondary Parameters

Expression Pedal

Morphing from Heel to Toe
An Expression Pedal can be used to change any grouping of knob Parameters in one smooth gesture. Programming an Expression Pedal is easy. You simply need to set end points for Heel & Toe. Here’s how:

1.  Press Pedal fully Heel down.
2.  Adjust any combination of the Parameter control knobs.
3.  Press Pedal fully Toe down.
4. Adjust any combination of the Parameter control knobs.
5. Save it or lose it. See “Saving a Preset.”
   Clear Expression Pedal Mappings To clear the Expression Pedal mappings for the knobs, hold the ACTIVE Footswitch and, while holding, press the ACTIVE Button until the Preset Ladder LEDs flash twice.
   NOTE:
   To use an Expression Pedal, the Exp Pdl Jack must be set to either [EXP] or [EXP + AUX]. See System Setup to select.

MIDI Messages

Save Preset
Enter Save Mode by pressing and holding the SWIRL Button, then a MIDI program change message will save a Preset to the Preset Slot of the given value 1-127.

Load Preset
MIDI program change message loads the Preset from the Preset Slot of the given value 1-127.
Note:
The bottom two Ladder LEDs will be lit when Presets 6–127 are selected via MIDI or Device Manager. Receive/send using the USB Port or Exp Pdl Jack

• CC 4: Expression Pedal
• CC 9: Tap RATE
• CC 14: ACTIVE/BYPASS (>=64 is Active)
• CC 15: SWIRL (>=64 is SWIRL)
• Parameters: CC Messages Map

System Setup

Enter System Setup
To access these Global Settings, apply power while holding ACTIVE Footswitch and button. Top two LEDs light when in System Setup. Changes are stored as they are made. Cycle power to exit System Setup.

• [EXP+AUX]

• TIP = Expression Pedal

• RING = Tap RATE

• [TRIPLE AUX]

• TIP = Increment Preset

• RING = Decrement Preset

• TIP + RING = Load Preset

• Note:
  Times out after a few seconds

• [MIDI BOX]

• Receive and Send MIDI via a MIDI Converter Box (Tip Active)

• [MIDI TRS]

• Receive MIDI directly with a DIN to TRS or TRS cable.

References

• EDM compatibility windows 32 bits - Eventide Audio
• Support - Eventide Audio

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>