TRUE FINE TD60003FL 6 Light Flush Mount Lighting Instruction Manual
- October 30, 2023
- TRUE FINE
Table of Contents
TRUE FINE TD60003FL 6 Light Flush Mount Lighting
Product Information
The 6-Light Flush Mount Lighting is a product that provides ambient lighting for your room. The product comes with a mounting bar, fixture body, canopy, finial, and six lamp arms. The product is designed to be wired to your outlet box and can be installed by following the instructions provided in the manual. The product uses six E26-base light bulbs (not included).
Product Usage Instructions
- Wiring Instruction: Start by inserting the green grounding screw into the hole with two raised dimples on the mounting bar. If the fixture comes with a ground wire, wrap it around the green grounding screw and connect it to the ground wire from the outlet box using a wire connector (not supplied). If the ground wire is not supplied, wrap the ground wire from the outlet box around the green grounding screw and tighten it. Never connect the ground wire to black or white power supply wires.
- Identify Fixture Wires: Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into (Group A or Group B) and connect the wires according to the directions given.
- Connect Fixture Wires from Group A: Place the fixture wire(s) from Group A evenly against the black wire from the outlet box. Do not twist wires together before using wire connectors. Fit a wire connector over the wires and screw the connector clockwise until you feel firmness. Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
- Connect Fixture Wires from Group B: Connect the fixture wire(s) from Group B to the white wire from the outlet box in the same manner as Group A. Make sure no bare wires can be seen outside wire connectors.
- Assembly Instruction: Fix the mounting strap (F) to the outlet box with screw (D). Connect the wires according to the picture provided in the manual. Pass Canopy (C) through Screw (E) and fix it with Finial (B). Rotate the lamp arm to adjust the lamp to the shape shown in the figure provided.
- Install Light Bulbs: Install six E26-base light bulbs (not included).
Cleaning Instructions
To clean the product, wipe the fixture with a soft cloth. Clean the glass with
a mild soap. Do not use abrasive materials such as scouring pads or powders,
steel wool, or abrasive paper.
Safety Information
Always switch off the electricity supply and allow it to cool for 10
minutes before changing the light bulbs. Contact the manufacturer via email at
service@24h-reply.com for any queries or concerns.
Overview
Assembly Instruction
- Fix Mounting strap (F) to outlet box with Screw (D).
- Connect the wires according to the picture above. (Please refer to the wiring instruction for details )
- Pass Canopy (C) through the Screw (E) and fix it with Finial (B).
- Rotate the lamp arm to adjust the lamp to the shape shown in the figure above.
- Install light bulbs (not included). Use six E26-base bulbs.
Wiring Instruction
-
Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to
ground wire from the outlet box (if not fixed on the outlet box) using a wire connector(not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES. -
Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below
[GROUP A]: Connect to Black House Wire| [GROUP B]: Connect to White House Wire
---|---
BLACK| WHITE
PARALLEL WIRE (round & smooth)| PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT TRACER| BROWN, GOLD OR BLACK WITH TRACER -
Take your fixture wire(s) from [Group A] and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
-
Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
-
Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
-
Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.
Product Specifications
- Input voltage 120V
- Rated power 60W MAX × 6
- Lamp socket E26
Product Packaging
- Fixture body × 1
- Mounting strap × 1
- Screw × 2 & Wire nut × 3
- Lamp instruction × 1
Cleaning
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do
not use abrasive materials such as scouring pads or powders, steel wool or
abrasive paper.
Safety Information
Always switch off the electricity supply and allow to cool for 10 minutes
before changing the light bulbs.
CONTACT US
E-mail: service@24h-reply.com
Print in china
Documents / Resources
| TRUE
FINE TD60003FL 6 Light Flush Mount
Lighting
[pdf] Instruction Manual
TD60003FL 6 Light Flush Mount Lighting, TD60003FL, 6 Light Flush Mount
Lighting, Flush Mount Lighting, Mount Lighting, Lighting
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>