TRUE FINE TD40018C 4-Light Caged Farmhouse Candlestick Chandelier Instruction Manual

TD40018C 4-Light Caged Farmhouse Candlestick Chandelier

Product Information: 4-Light Chandelier

The 4-Light Chandelier is a lighting fixture that comes with a mounting bar, fixture chain, and canopy. It has two groups of wires, Group A (green, bare copper, and white ribbed wires) and Group B (wires with different colors). It also has a grounding screw for safety purposes. The product is packaged with assembly and wiring instructions, and it can be cleaned using a soft cloth and mild soap.

Product Usage Instructions

1. Wiring Instruction:
   • Insert the green grounding screw into the hole with two raised dimples on the mounting bar.
   • If the fixture comes with a ground wire, wrap it around the green grounding screw, then connect it to the ground wire from the outlet box using a wire connector (not supplied).
   • If the fixture does not come with a ground wire, wrap the ground wire from the outlet box around the green grounding screw and tighten it.
   • Take note of the color of the wires on your fixture and connect the wires according to the directions below:
   • Group A: Connect to Black House Wire
   • Group B: Connect to White House Wire
   • Do NOT connect the ground wire to black or white power supply wires.
   • Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
   • Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
2. Assembly Instruction:
3. Connect Lower lamp body (C) and Upper lamp body (F) with Short iron tube (E), then lock them with Cap (B).
4. Thread the wires through Long iron tube D) and Upper lamp body (F) and screw them together.
5. Fix Mounting strap (L) to outlet box with Screw (K).
6. Thread the wire and Fixture chain (H) through Canopy (J), then link Loop (G) and Mounting strap (L) with Fixture chain (H).
7. Connect the wires according to the wiring instruction.
8. Fix Canopy (J) to Mounting strap (L) with Canopy lock ring (I).
9. Cleaning:
   To clean the fixture, wipe it with a soft cloth. Clean the glass with a mild soap. Do not use abrasive materials such as scouring
   pads or powders, steel wool, or abrasive paper.

Safety Information:
Always switch off the electricity supply and allow to cool for 10 minutes before changing the light bulbs.

If you have any questions or concerns regarding the product, you may contact the manufacturer at service@24h-reply.com.

Overview

Assembly Instruction

1. Connect Lower lamp body (C) and Upper lamp body (F) with Short iron tube (E), then lock them with Cap (B).

2. Thread the wires through Long iron tube (D) and Upper lamp body (F) and screw them together.

3. Fix Mounting strap (L) to outlet box with Screw (K).

4. Thread the wire and Fixture chain (H) through Canopy (J), then link Loop (G) and Mounting strap (L) with Fixture chain (H).

5. Connect the wires according to the picture above.
   (Please refer to the wiring instruction for details )

6. Fix Canopy (J) to Mounting strap (L) with Canopy lock ring (I).

Wiring Instruction

1. Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector(not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
   NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.

2. Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
   [GROUP A]:
   Connect to Black House Wire| [GROUP B]:
   Connect to White House Wire
   ---|---
   BLACK| WHITE
   PARALLEL WIRE (round & smooth)| PARALLEL WIRE (square & ridged)
   WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
   BROWN, GOLD OR BLACK WITHOUT TRACER| BROWN, GOLD OR BLACK WITH TRACER

3. Take your fixture wire(s) from [Group A] and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.

4. Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.

5. Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.

6. Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

Product Specifications

• Input voltage 120V
• Rated power 60W MAX × 4
• Lamp socket E12

Product Packaging

• Fixture body × 1 & Long iron tube × 1
• Short iron tube × 4 & Cap × 8
• Loop × 1 & Fixture chain × 1
• Upper lamp body × 1 & Lower lamp body × 1
• Mounting strap × 1 & Canopy × 1
• Screw × 2 & Wire nut × 3
• Lamp instruction × 1

Cleaning
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Safety Information
Always switch off the electricity supply and allow to cool for 10 minutes before changing the light bulbs.

CONTACT US
E-mail: service@24h-reply.com

Print in china

References

• Digital Services, Technology and Consulting | Reply

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>